-
Why don't you blow up the newly bought floor tiles without cutting everything? If the tile with a certain water absorption rate is not soaked in water before paving, after paving, in the process of cement mortar condensation and strength rise, the tile will absorb its moisture Use cement mortar to pave tiles (mainly referring to wall tiles), and the tiles need to be soaked in water for about two hours in advance.
The higher the density of the brick, if the tile with a certain water absorption rate is not soaked in water before paving, after the paving in the process of cement mortar condensation and strength rise, the tile will absorb its moisture, 1. This is very serious, but in the actual construction, it will really encounter many times, many times it may be a problem caused by a deformation of your wall, because the cracks caused by this are more regular. Precautionary measures: Before laying bricks on the light wall, ask the construction personnel to test the wall to see if the wall is installed firmly; Secondly, it is recommended to make a layer of steel wire mesh on the side of the wall tiles to improve the strength and load-bearing capacity of the wall.
For the insulation wall, the insulation layer is usually made of polyboard material, and the original insulation wall can be removed and replaced by bricks (commonly known as foam bricks). Due to the strong adhesion of bricks, it can effectively reduce tile cracking, falling off, etc., which will not be easily corroded, and the landlord may buy the inferior floor, the landlord or ask the dealer! I'm just a personal opinion, the general *** floor, such as the Meidi stone plastic lock floor, has the effect of anti-corrosion, it should be corroded.
-
1.The quality of the tiles themselves.
Cheap tiles are prone to problems, and the glaze of cheap tiles is thin and cracks when it expands and contracts in the cold. If the owners blindly choose the cheap ones when buying tiles, then there is a great possibility of problems in the later stage. Cracks in large areas of tiles are not just a matter of a few bricks, then it is a matter of tile quality.
2.The craftsmanship of the tiling master.
Tiling is a technical job, if you meet a new craftsman, then the tile problem is certain. However, the bricks that are not generally technically pasted will not have cracks in a large area, and may only have a few cracks.
If it is not an all-inclusive decoration, if the owner wants to find a worker to lose money, the worker will generally shirk the problem of the tile. When the owner goes to sell tiles, the tiles seller will shirk to the cement and workers, and in the end they can only suffer their own losses. This is the disadvantage of the half-pack, and the division of responsibilities is unclear.
3.The cement grade is higher.
Commonly used ordinary cement content, 525, the higher the strength of the base, the higher the price. The general decoration must be 325. The higher the mark, the faster the water will be collected, and the ash will shrink and crack in the lower layer, and the brick will crack with it. Special attention should be paid in summer, so the craftsmanship of workers is also required.
4.The building is sinking.
After the building is built, after a period of time, usually the foundation of the building has to fall to a certain extent, so there will be cracks.
-
Watering before cutting, don't you understand this basic common sense? Or take a bucket to soak the tile and then cut it, just like an original stone, it will definitely get stuck and scratched when you open it.
-
This is enough to prove that this slab brick is not of good quality, and it is best to replace it quickly, otherwise it will be too late.
-
Dear, hello, I am very happy to answer for you why the newly bought floor tiles are coarse and do not cut everything on the explosion pattern is 1, the quality of the tile is too poor: the density of the tile is too small, the anti-strain ability is poor, especially the tile in the process of hygroscopic expansion or thermal expansion and contraction, it is easier to crack. 2. The construction is not standardized
When the base layer of the wall is not properly treated, the cement grade is too high or the cement content in the cement mortar mix ratio is too high, these aspects will cause the cracking of the tile. 3. No soaking in water before construction: there will be certain gaps in the production of tiles, and after soaking in water, absorbing enough water can prevent the tiles from being too dry, because the water blocks the tensile force of the mud mortar and cracks.
-
The quality of floor tiles is very important, because the frequency of stepping on floor tiles is very high, and it is very difficult to replace, once damaged, it is necessary to destroy the original ground decoration to replace and repair, so good floor tiles are very necessary. Now there are many types of floor tiles, the characteristics of each material are different, and the environment is different, you can choose according to your actual needs.
1.All-over bricks.
The so-called full-body brick refers to the fact that in the distribution process, all the powder distributed on the press preparation table is the same powder, and the ceramic tile after firing is the same pattern and color from the bottom to the surface. The whole brick is unglazed, so it is named because the front and back of the material are the same. Generally speaking, full-body bricks are more wear-resistant, but they are not as rich in color as glazed bricks.
2.glazed tiles.
Glazed bricks are bricks whose surface has been glazed. The surface is fired with glaze and layered, and the main body is divided into two kinds: clay and porcelain clay, the back of the clay fired is red, and the back of the porcelain clay fired is gray-white. The surface of the glazed tile can be made of various patterns and patterns, which is richer than the polishing color and pattern, because the surface is glaze, so the wear resistance is not as good as the polishing turn.
3.Polished tiles.
Polished brick is a kind of bright brick made by polishing the surface of the whole brick body, which belongs to a kind of whole body brick. Compared with the whole body brick, the surface of the polished tile is much smoother. Polished tiles are hard and wear-resistant, making them suitable for use in most indoor spaces except washrooms and kitchens.
On the basis of the use of seepage technology, polished tiles can make a variety of imitation stone and imitation wood effects.
4.Vitrified tiles.
In order to solve the problem of easy dirtiness of polished tiles, another kind of vitrified brick appeared. Vitrified tiles are actually full tiles. Its surface is smooth but does not need to be polished, so there is no problem of polishing porosity.
Vitrified tile is a kind of strengthened polished tile, which is fired at high temperature, and the texture is harder and more wear-resistant than polished tile. Undoubtedly, it's just as high. Vitrified tiles are mainly used for floor tiles.
5.Mosaic.
The volume of mosaic is the smallest among all kinds of tiles, and it is generally commonly known as a brick. Mosaic gives a nostalgic feel and is the material that decorated the walls and floors in the 90s of the 20th century. Mosaic combinations can vary a lot, for example, on a plane, and can be expressed in a variety of ways:
Abstract patterns, jumps or transitions in tonal shades, patterns for other decorative materials such as tiles, and more. For the curved surface or corner of the room, the glass mosaic can give full play to its small size, and can cover the curved bread smoothly and completely.
Glazed bricks and vitrified bricks are the two most used materials, which are suitable for spaces with more public activities, such as living rooms and corridors, because these two kinds of bricks not only have a more exquisite appearance, but also have good wear resistance. Several other floor tiles also have many advantages and are suitable for different spaces. When choosing floor tiles for decoration, it is recommended to know more about products made of several materials, and use different materials for the space that is not used, so as to ensure the life and convenience of use.
-
The newly bought floor tiles cannot be cut directly with a cutting machine, you need to put the floor tiles in the water to bubble, and then you can cut them with a cutting machine, so that they will not burst.
This is normal: the glaze layer is not worn and the wax of the protective layer is not worn away. >>>More
Why is there an arch of floor tiles? How can it be prevented? How to deal with it? >>>More
I don't have a feeling for anything anymore.
No way, people feel when they are alive, unless you are dead; >>>More
Hot beef is easy to disperse, so wait for the beef to cool before cutting. Here's how: >>>More
Grades are an important criterion for others to evaluate your studies, so take them seriously. Note: Now it's time to concentrate on a thorough review. >>>More