How do you dismantle the glass of Volkswagen Santana?

How to remove the front windshield:

1.lift the wipers;

2.Use a utility knife to scratch off the glass glue around the glass; (Be sure to draw to the end, otherwise the glass will not be able to be taken off in the later stage).

3.Then use a thin steel wire to dig around the glass, and separate the surrounding adhesive glue to facilitate the 5261 glass dismantling; 4102

4.It is best for two people to push the glass out of the four corners from the car, and it is best for someone to press the glass outside to prevent the glass from breaking;

5.Clean the glass glue around the glass;

6.Clean the glass glue and dirt in the glass tank;

7.After completely cleaning the glass glue in the glass tank, the weather-resistant glass glue of black 1653 was inserted;

8.After the glass glue is played, it is good to install the glass.

Open the door and remove the door panel, remove the lifting motor, remove the lifting screw fixing screw, remove the glass fixing screw, and the glass will fall off.

Hello. lift the wipers;

Use a utility knife to scratch off the glass glue around the glass; (Be sure to draw to the end, otherwise the glass will not be able to be taken down in the later stage) and then use a thin steel wire to dig around the glass, and separate the surrounding adhesive glue to facilitate the 5261 glass dismantling; 4102

It is best for two people to push the glass out of the four corners from the car, and it is best for someone to press the glass outside to prevent the glass from breaking;

You need to remove all the tape from the edges and just do it.

1. First of all, adjust SAIC Volkswagen by hand.

2. Next, place the screwdriver.

Insert into the rearview mirror of the SAIC Volkswagen Volkswagen Santana car and put the rearview mirror drive.

Summary. Hello dear! The steps to remove the Santana rear door handle are as follows:

1. First of all, prepare the tools needed for the whole disassembly and assembly process, a word to change the cone, a T-20 spline, and then prepare for the next operation process, the whole process uses these two tools, or quite easy. 2. Break down the inner handle by hand, and then you will see the left and right two small covers, take out the word change cone, and gently pry the two small covers with the word change cone, you don't need to take it off, you can pry it open. 3. At this time, we will see the screws that fix the inner handle, a total of two on the left and right, take out the T-20 spline, use the T-20 spline to disassemble the two screws, and the disassembled screws should be put away for installation.

4. After the screw is disassembled, the left hand holds the left side of the inner handle, and the right hand holds the right side of the inner handle, and then gently breaks it outward, so that the inner handle is separated from the big top, and it should be lighter when breaking it, because there is a small plastic clip on the inner handle, which is easy to break. 5. In this way, the inner handle will be removed, and the inner handle of the roof should be put away, preferably in a soft place to avoid wearing the surface.

This question is up to me, it takes a little time to type, so please be patient.

Hello dear! The steps of disassembling the handle outside the back door of Santana are as follows: 1. First prepare the tools needed for the entire disassembly process, a word to change the taper, a T-20 spline, and then prepare for the next operation process, the whole process uses these two tools, or quite easy.

2. Break down the inner handle by hand, and then you will see the left and right two small covers, take out the word change cone, and gently pry the two small covers with the word change cone, you don't need to take it off, you can pry it open. 3. At this time, we will see the screws that fix the inner handle, a total of two on the left and right, take out the T-20 spline, and use the T-20 spline to disassemble the two screws. 4. After the screw is disassembled, the left hand holds the left orange side of the inner handle, and the right hand holds the right digging side of the inner handle, and then gently breaks it outward, so that the inner handle is separated from the big top, and it should be lighter when breaking it, because there is a small plastic clip on the inner handle, which is easy to break.

5. In this way, the inner handle will be removed, and the inner handle of the roof should be put away, preferably in a soft place to avoid wearing the surface.

The operation is as follows: 1. First prepare the tools needed for the whole demolition process, and change the cone one by word.

handful, then open the door and prepare for the next demolition.

2. First remove the handle cover of the rear door interior panel. Take out the slotted taper and pry it up from the edge gap between the door trim panel and the inner handle cover as shown in the figure.

3. Pry open the clips inside little by little, a total of three clips, everyone must pry the right position when prying, and gently pry it.

4. After all the three clips are pried open, hold the door interior panel handle cover with your hand, gently pull it out, and remove it, check whether the clip is intact and stuck on the inner handle cover, it must be light, to avoid some scratches, affecting the appearance.

5. At this time, you will see the screws that fix the door trim panel, a total of two, take out the T-30 spline, remove the two screws with the T-30 spline, and put the removed screws together with the previous inner handle cover.

I don't know which Santana you're referring to? However, the door interior must be removed, there is a triangular interior panel behind the rearview mirror that covers the mirror screws, which can be pried off with a screwdriver, and if there is an electrically adjustable rearview mirror, the entire door interior must be removed, and there is a motor cable inside.

Summary. If you want to remove the roof of this model, this is still more troublesome, this first needs to remove the front dome lights, then remove the handles on both sides, and then remove the A-pillar B-pillar, and all the trim plates of the C-pillar, and remove the front visor. Then the whole downturn can be used on the top of the roof of the shed is fixed with buckles, as long as the above fixed parts are removed, and then this top can be directly pried down, and then look at some of the plugs above, pull out the plug, and then you can remove it, this is still more troublesome.

If you want to remove the roof of this model, this is still more troublesome, this first needs to remove the front dome lights, then remove the handles on both sides, and then remove the A-pillar B-pillar, and all the trim plates of the C-pillar, and remove the front visor. Then the whole downturn can be fixed with the buckle used on the roof of this shed, as long as the above accusation some fixed parts are removed, and then this top can be directly pried down, and then look at some of the plugs above, pull out the plug, and then you can remove it, this year is still more troublesome.

I want to change the radio antenna, just take the back apart.

If you want to eliminate the difference in the back, you only need to remove the C-pillar trim at the back and then you can pry the ruler directly from above to take the sleepy skin, but this is easy to break the roof, and it is best to get it down as a whole.

No. Isn't it a hassle?

This one is still more troublesome, you better go to the repair shop and let the maintenance man replace it for you.

There was a small hole in the side of the door, and you could see a small plastic hole inside, and the extra piece of the small hole was hooked out with wire.

Let's talk about the front door handle car and push it forward, and then there is a screw on the front door handle car directly opposite the edge of the door, and you can unscrew it down!

Do you know how to dismantle the handle?