The flush toilet works and the toilet is loose

The flush toilet consists of the following main parts: inlet pipe, outlet pipe, seepage pipe, water plug (inlet and outlet), float, drain knob and lever, water refill mechanism, water tank, urinal (the urinal has a bend that connects to the water tank).

Utilize the water discharge knob and the water plug to control the water discharge and water storage, when using, rotate the water discharge knob, use the metal rope or nylon rope connecting the water plug to pull up the water plug, the water plug pulls out the water outlet pipe port upward, the water outlet pipe puts the water into the urinal and uses the gravity of the water and the kinetic energy converted by the potential energy to flush the excrement dirt into the sewer pipe, and at the same time, when the water level drops to a certain water level, the water plug is re-pressed into the port of the outlet pipe due to the negative pressure generated by the gravity of the water, and the water outlet is blocked. At this time, the water is no longer released and a new stage of water storage begins; When the water level drops, while flushing the urinal, the float together with the lever is driven by the gravity of the float due to the drop in the water level, and the lever is opened to start synchronous water replenishment; In the water replenishment stage, the buoyancy and lever of the float are used to control the water replenishment of the water tank, and when the float descends to the lowest position, the water plug is pressed into the mouth of the water pipe by negative pressure, and the water tank begins to store water; The water inlet pipe is connected to the water pipe, which is responsible for the input of the water source, and when the water supply reaches a certain height, the buoyancy of the water will lift the float up to the linkage lever, close the water supply mechanism, and stop the water supply.

It is best to find a professional master, do not look for guerrillas on the street, if you have strong hands-on ability and are not afraid of dirty, you can solve it yourself, tools to a shovel, a bottle of glass glue and a gun of squeezing glass glue, first turn off the water into the toilet, and then clean up the place where the toilet and the ground contact is cleaned with a shovel, and then move the toilet to the side, it is best to be supported, so as not to break, and then lie on the ground to see if the drain of the toilet and the drain of the ground are aligned, and put the toilet right after alignment, and then the glue, It is best to have someone hold the toilet to make it a little gap with the ground, and put the glue in, and the U-shaped in front must be put in place, and the glue can be used when it is dry, and now it is cold to wait for three to four days. If you are not sure, you should still find a professional master, it is not cost-effective to break the toilet.

Oh, my God! The master actually used cement to install the toilet for you, it is too unprofessional, the installation of the toilet is to use glass glue, the only bathroom below teaches you how to install the toilet, I hope it will help you, the current installation method is relatively simple. The toilet bowl is connected and sealed with a so-called toilet flange ring (plasticine), and the bottom surface of the toilet bowl is sealed with silicone (silicone) sealant.

When installing, the toilet must sit firmly on the ground, and it can be adjusted by padding, and must not be shaken, and then it can be glued and sealed.

The glass glue can be made of silicone sealant for kitchen and bathroom. When installing, it is necessary to ensure that the place where the glue is applied is clean and dry, so as to ensure that the sealant is firmly bonded.

The mouth of the sewage pipe should be level with the ground, neither high nor low. If the sewage nozzle is half a centimeter high, you have to see if there is enough gap between the sewage outlet and the sewage outlet you bought to accommodate the flange, otherwise the toilet will not be able to sit firmly on the ground, or the bottom of the toilet will have to be padded all around, and it is not easy to be very stable.

1 Treat the ground drain as high as the ground, and then press the center of the outlet to draw a cross extension.

2 Draw a crosshair along the toilet outlet to the spot where you can see the edge of the toilet, 3 Put the horse to the drain with the crosshairs overlapping.

4 Draw a line along the outside of the toilet bowl and remove it.

5 Place the toilet sealing flange on the drain on the ground, and make a circle of glass glue along the inside of the overall circle line of the toilet bowl.

6. Place the toilet on top of the crosshair, press the bottom edge of the toilet on the glass glue, connect the water hose, and install an angle valve at the water outlet on the wall to turn off the water for maintenance in the future.

7 Do not use and keep the ground dry for 24 hours.

The only bathroom for you is here, I hope these will be helpful to you!

It's caused by the glue at the bottom of your toilet.

There are great drawbacks to installing with cement, and now all are installed with glass glue. The following tells you how to install it with glass glue.

Place the toilet tank lid in a safe place and mark the base with a pen in the existing position of the toilet. Put the toilet down, pour the water inside, and clean the ground at the same time (don't erase the marks when cleaning the ground), wait for the toilet base and the ground to be completely dry, evenly coat the glass glue in the line of the drawn mark line (inside the circle), and put the toilet on the glass glue inside the mark line. Remember to use normally after 18-24 hours.

As for the loud sound, the sound will disappear after reinstalling it according to the above method.

As long as the dirty water doesn't come out, you can go to the toilet with confidence, and the dirty water can't fall downstairs.

There are two ways for you to do it now, either reinstall the toilet yourself or ask the master to come to your door and ask him to install it again.

The "pumping" of the toilet bowl refers to the S-shaped bend under the toilet, and when the water surface in the toilet exceeds the high point of the S-bend, the siphon phenomenon is formed, which can pump the water and dirt of the toilet together. Until only a small amount of water remains, the siphon destroys, leaving a small amount of water, forming a water seal.

Siphon: The phenomenon of siphoning is caused by the gravitational force and potential difference between liquid molecules. That is, the pressure difference of the water column is used to make the water rise and then flow to a low place.

Since the nozzle water surface is subjected to different atmospheric pressures, the water will flow from the high-pressure side to the low-pressure side until the atmospheric pressure on both sides is equal, and the water surface in the container becomes the same height, and the water will stop flowing. The siphon phenomenon is used to quickly pump out the water in the container.

If you are not a professional, you should call the master to install it, so that it is safe and you will not be delayed downstairs by your neighbors. And if it is not installed, it will waste water! It is advisable to carry out repairs as soon as possible.

The principle of the flush toilet is to use the drain knob and plug to control the discharge and storage of water. When using, rotate the water discharge knob, use the metal rope or nylon rope connected to the water plug to pull up the water plug, pull out the water plug up, pull out the water outlet pipe port, the water outlet pipe puts the water into the urinal, and uses the gravity of the water and the kinetic energy converted by potential energy to flush the excrement dirt into the sewer pipe.

Tips for using flush toiletsThe toilet is a relatively large water consumption, and the use skills of the flush toilet are:

1. The height of the float can be adjusted to control the water level in the tank, which determines the amount of flushing water used each time.

2. For double-speed flush toilets, press the blue button when flushing urine and use the white button when flushing stool, and the difference in water consumption between the two is very large.

The toilet works as follows:1. When you press the button, you pull the chain inside the toilet, so you can open the flush valve.

2. Then you will find that there is a large amount of water in the tank to flush into the toilet, so as to flush it clean, and then the flush valve will also return to its original position.

3. The impulse of the water will activate the siphon in the urinal, and the siphon will suck the dirt in the urinal into the drain.

4. At the same time, the water level in the tank will drop, and the floating block will also drop. The lowered float opens the water valve.

5. The water flows through the water valve to fill the water tank and urinal. When the tank is filled with water, the float will float up, and when the float reaches a certain height, the water supply valve will close.

6. If the toilet is faulty and the water valve cannot be closed, the overflow pipe can prevent the water in the tank from overflowing.

A flush toilet consists of the following main parts: inlet pipe, outlet pipe, seepage pipe, plug (inlet and outlet), float, drain knob and lever. Be sure to understand the role of each of the above components in the work.

When discharging water, pull the drain knob, and the knob pulls up the water outlet plug through the lever. In this way, the water from the tank will be released. After the water is released, the outlet plug falls down, blocking the water outlet.

At this time, the float is also at the bottom of the tank due to the drop of the water surface. The fall of the float drives the lever to pull up the water inlet plug and let the water enter the tank. As the water rises, the float will gradually increase due to buoyancy until the inlet plug is pressed down by a lever and the inlet is blocked.

This fills the tank with water again. Think about it, what is the purpose of the adjustable knob?

When the inlet pipe leaks due to a malfunction (e.g., the inlet plug fails to block the inlet or the inlet pipe breaks), the water level in the tank will continue to rise and eventually overflow the tank. And the setting of the seepage pipe solves this problem.

When the water level rises to the seepage nozzle, the water flows into the toilet bowl from the seepage pipe and does not allow the water to overflow the tank. When the inlet pipe is working normally, the water surface in the tank will not reach the seepage nozzle, so there is no need to worry about the water flowing away.

As shown in the experiment, when the coarse straw is placed over the thin straw and inserted vertically into the water and raised slightly, the coarse and thin straws form a special siphon, and the water continues to flow down the thin pipe. Flush toilets also make use of the principle of siphons.

If you install a toilet in the bathroom, it will bring great convenience to your daily life. So what is the principle of toilet flushing? PChouse will take you to find out.

The water tank controls the toilet to release water and add water, it relies on buoyancy and gravity, plus the principle of lever to work, when we use the toilet will press the waterproof button, then the water plug will be pulled up by the lever principle, and at the same time block the water inlet, then the water will flow into the toilet, the water in the tank will flow out, the water plug will fall again, block the water inlet, open the water inlet, and the water tank will start to store water at the same time. The process of water tank storage is done by buoyancy and gravity, the float loses buoyancy and sinks, open the water injection valve (at this time the water injection port has been opened), and the water flows into the water tank, so that the water tank can be stored.

When the water enters the toilet after how it works, this is a siphon phenomenon, when the toilet is filled with water, the water will be discharged to the water inlet, that is, the S-shaped pipe, the S-shaped pipe is also called the siphon, it can drain the water to its indispensable, the toilet gathers a lot of water in a short period of time, and discharges it in a short time, it is its credit, when the water is almost discharged in the S pipe, the S pipe will form a short low-pressure environment, under the action of water pressure, the water will be squeezed into the S pipe, when the low pressure disappears, Part of the water cannot be discharged back to the toilet, forming a water seal, which is why the water we see will all be discharged into the S pipe and come out again.