How to install the heating pipes, how to install the heating pipes?

Single-tube series The characteristics of single-tube series connection are low material usage, relatively weak labor intensity, and shorter transformation time. The water of the whole system passes through the first set of radiators of the system, then the second group, then the third group ......, so the water temperature is gradually decreasing in the order of series. Under the same conditions, the temperature of the first and last two groups of heating to the room can be more than 2 degrees, in order to adjust the water temperature of a single group of heating, a bypass valve must be added at the inlet and outlet of the radiator front, some use a three-way regulating valve, and some use three gate valves.

If a single-pipe tandem system is not bypassed, turning off one set of heaters will cause the entire system to be immediately interrupted, and all other heaters will not be hot. Moreover, the number of radiators that need to be configured in a single tube series is larger, and in order to meet the needs of the system circulation, the main body of this heating system also needs to be relatively coarse.

Double-pipe heteropathic parallel connection The characteristics of double-pipe heteropathic parallel connection are that the pipeline stroke is shorter, each group of radiators can be controlled separately (the inlet and return water inlet and return places at the front end of the radiator are controlled by a control valve), the temperature is relatively uniform, and the water flow balance of the system will be greatly improved compared with that of single-pipe series, but this system still has certain limitations. The water flow rate of each group of radiators is different, and the return water of the front-end radiator is relatively fast because it is closer to the main pipeline, while the backwater return at the rear end is slower, which may cause the phenomenon that the end heating is not hot or not hot enough. However, it doesn't matter, you can solve the problem by adjusting the valve, and turn off the return valve of the front end heating in turn to ensure that the system is balanced and let the end heating slowly heat up.

Double-tube co-accurricular parallel Double-tube co-accord parallel, also known as twin-tube co-accurric. The characteristics are basically the same as the two-tube asynchronous parallel. However, there is a difference in the operating principle, simply put, it is called first supply and then return, that is, the return water of the first group of radiators at the front end does not circulate to the main pipeline temporarily, but continues to go down, connect the return pipe of the next group of radiators, and so on....Pull a return line from the radiator at the very end and return it to the return pipe of the main pipe.

The water flow rate of each set of radiators in the system is basically the same, and the system is very balanced, and there is generally no phenomenon of no heat at the end. It can be said that it is the best way to balance the hydraulic system.

Precautions. The radiator pipe installation should have a slope, if the design does not require, the slope should meet the following requirements: 1. Hot water heating and hot water ** pipeline and steam flowing in the same direction.

1. Single-tube series connection.

Features: low material usage, short transformation time, relatively weak labor intensity.

In the arrangement of heating pipelines, the single pipe series is a common one, and the water of the whole system passes through the first group of radiators of the system, then the second group, and the third group. For this reason, the water temperature is gradually lowered in the order of series. This type of heating duct installation requires a larger number of radiators, and in order to meet the circulation requirements of the system, it also requires a thicker heating system main.

2. Double-tube parallel connection.

Features: The pipe stroke is short, each group of radiators can be controlled separately (the front end of the radiator inlet and return water is added with a control valve), the water flow balance of the system will be greatly improved compared with the single pipe series, and the temperature after use is more uniform.

This heating pipe installation mode, still has certain limitations at present, because the water flow rate of each group of radiators is different, its front end return water is close to the main pipeline, so the return is faster, and its rear end return water is slower, and this situation may cause the phenomenon that the end heating is not hot enough or not hot.

Of course, the specific problem is solved, and the owners can solve this problem by adjusting the valve, and turn off some of the return valves of the front end heating in turn when the radiator system is working, so as to ensure the balance of the system and let the end heating continue to heat up.

3. Twin tubes are connected in parallel in the same way.

Double-pipe parallel connection, also known as double-pipe parallel, has the same characteristics as double-pipe parallel, but the two heating pipe installation methods are different in terms of operating principle. To put it simply, the backwater of the first group of radiator systems at the front end continues to go down, and does not circulate to the main pipeline for the time being, and is connected to the backwater pipes of the next group of radiators, and so on. When you reach the radiator at the very end, you will return to a return line and return to the return pipe of the main pipe.

Questioned on 2020-05-08.

See all 2.

Electric Heating Film Electric Heater - Jingdong Home Appliances Smart Life, Simple and Extraordinary, Rush to Buy for a Limited Time!

It is recommended for you according to the heating mentioned in the text.

Electric Heating Film Electric Heater - Jingdong, complete categories, buy high-quality home appliances, and enjoy a smart interconnected life!

Beijing Jingdong Century Information Technology **** advertisement.

Heating insulation steel pipe Huabao steel pipe wholesaler supply price.

It is recommended for you according to the heating mentioned in the text.

Heating insulation steel pipe Huabao steel pipe, specializing in the production of all kinds of anti-corrosion pipes, manufacturers ship, on-demand customized heating insulation steel pipes to Huabao, no middlemen to earn the difference, consult as soon as possible!

Hebei Huabao anti-corrosion and thermal insulation pipe manufacturing Co., Ltd. Ad.

Floor heating pipe manufacturers, smart people all choose to warm the first sen, energy saving. Environmental protection. No contamination.

Floor heating pipe manufacturers, **cold, **warm first forest, in the cold winter wax moon to support a warm harbor! Floor heating pipe manufacturer, simple operation, one-stop support, free guidance throughout the process, this winter is looking forward to working with you to resist the cold winter!

Heating duct installationThere is a certain technical content and construction specifications, such as slotting, pipe layout, etc., all need special personnel to operate, if these specifications are not strictly implemented, it will eventually affect the heating effect or service life of the heating code. SoHeating pipesHeating Duct Installation Specifications:

1. Installation of radiator main pipe:

When the radiator main pipe is systematically arranged, it should be coordinated with the use requirements of the building, the heating system diagram, and the layout of the radiator, so as to save pipes and facilitate installation and maintenance.

The main pipe of the radiator pipe is usually surface-mounted, and when surface-mounted, it should be arranged in the corner of the exterior wall and the wall between the windows as far as possible. Before the main pipe is installed, the radiator is in place, and the riser is installed after finding the straightness, so that the size of the main pipe can be accurate. The semicircular bend on the double riser should be accurate and straight, and the branch pipe should be in the middle of the semicircular bend, and it should not be wrong or wrong.

After the installation of the pipeline, check the coordinates, elevation, reserved mouth position and pipe diameter is correct, and then straighten, with a level to check the slope, after the adjustment is qualified, and then adjust the elevator bolt U-shaped card, so that its tightness is moderate, straight and consistent, and finally weld the stop wrench at the fixed card.

2. Installation of radiator branch pipes

When installing radiator branches, the form of concealed installation is usually adopted, and the radiator branch lamp of concealed or semi-concealed installation needs to be adapted to the corner of the radiator groove wall in order to achieve an aesthetic effect, and the branch pipe connecting the radiator should have a slope. The slope radiator of the water supply branch pipe of the upper supply and lower return, and the slope riser of the return water branch pipe; There is no exhaust device on the top water supply riser, the slope riser of the water supply and return branches, the slope radiator of the water supply branch pipe of the other layers, and the slope of the return branch pipe.

The installation of radiator branches should be carried out after the installation of the radiator and riser, or at the same time as the riser. When the radiator branch pipe passes through the wall, in addition to adding a casing, it should also be noted that the branch pipe should not have a joint in the wall. When installing the valve on the branch pipe, the side near the radiator should be connected with the detachable parts, and when installing the radiator branch pipe, the steel pipe must be adjusted appropriately before meeting, so as not to distort the branch and riser.

The above is for you how to install the heating pipes? The entire contents of the heating duct installation specification.

The heating duct installation method is as follows:

1. Pipeline bonding should not be carried out in an environment with high humidity, and the operation site should be kept away from the fire source to prevent impact, in 20.

2. Before bonding, the inner side of the socket and the outer side of the socket should be wiped clean with a clean cotton yarn or dry cloth, and the adhesive surface should be kept clean. If the surface is stained with oil, it should be wiped off with cotton yarn dipped in acetone and other detergents.

3. When applying the adhesive with an oil brush, the inside of the socket should be coated first, and then the outside of the socket. When applying the socket, it should be evenly and appropriately spit from the inside to the outside in the axial direction, and should not be missed or applied too thickly.

4. After the socket is coated with adhesive, it is advisable to align the axis and insert it continuously within 20s. The depth of the pipe end insertion socket should be marked on the surface of the insertion tube end according to the measured socket depth, and the tube should be rotated 90° after insertion.

5. After plugging, wipe the adhesive extruded from the outside of the joint immediately. The force should be avoided, and it should be allowed to stand until the interface is solidified, and the installation can be continued only after the joint is firm.

6. The adhesive joint should not be operated below the ambient temperature of 0, and the adhesive should be prevented from freezing. Do not use open flames or electric stoves to heat the adhesive.

Dear, I am glad to answer for you: the installation method of household heating pipes is as follows: 1. First open the wall and groove, then connect the pipe and test the pressure, do not take off the table after the pressure test, and then check whether the value on the table has changed, if there is no change, it means that the pipe is not leaking.

2. Set the direction of the pipeline, pay attention to the need to set less curves, and the setting of the groove is slightly larger than the pipe diameter. 3. If you find the location of the radiator, you need to test it back and forth, choose the best location, and pay attention to the beauty and safety. 4. Then install the radiator, pay attention to ensure that it is closed, and there can be no water leakage.

5. Detect and test the radiator, and generally leave the valve during construction, and do the stamping test after the installation is completed, so as to ensure that there is no leakage.

Many people in life do their own home appliance installation, but because we are not professional in the installation and maintenance of these home appliances, it is inevitable that mistakes will occur in the installation process or lead to the severity of the problem. Below, let the Tuba Rabbit technical staff explain to you: about the installation steps of household heating pipes!

The installation of heating pipes does not seem complicated, but in the process of installation, there is still a certain degree of difficulty in positioning, slotting, etc. Therefore, if you want to install heating pipes by yourself in life, you must first understand some basics about installing heating pipes

1. First of all, it is necessary to measure and arrange the circuit of the heating pipe, to cooperate with the heat dissipation in use, and to facilitate the maintenance of the problem after installation, and it is best to install the heating pipe in the corner or window.

2. In the process of installation, the radiator should be fixed first, and the size of the pipe should be measured. When installing the pipeline, remember to be straight and accurate to the branch pipe when the riser, and there can be no mistakes or mistakes. After the installation is completed, it is necessary to check whether the coordinates and the position of the reserved port are normal, and it is best to measure it with a ruler.

When all adjustments are made, each fixed clamp is welded.

3. If for the sake of aesthetics, you can choose to use concealed installation when installing heating pipes at home, and remember to slope the riser of the backwater branch pipe when installing. In addition, the water supply branch pipes of other layers should be sloped to the radiator, and the main pipe should be in the slope direction. If the radiator branch pipe is over the wall, remember to add a casing.

Then remember to install the valve close to the radiator for easy removal and connection.

How to choose a heating pipe

1.The materials of heating pipes mainly include aluminum-plastic pipes, PPR pipes and PB pipes.

1) Compared with other pipes, the choice of aluminum-plastic pipe is not easy to be corroded, and the aluminum-plastic pipe has good thermal insulation, and can also be bent at will to facilitate installation and maintenance. However, the only disadvantage of aluminum-plastic pipe is that it is relatively higher than other pipes.

2) The material of PPR pipe is very light, and it is not easy to resist corrosion and has good heat resistance, especially long service life.

3) PB tubes also have a long service life and can withstand high temperatures for a long time, but PB tubes need to block oxygen and have a high oxygen permeability.

2.In daily life, we should choose the size of the heating pipe according to the place where it is installed in our home, and then choose the length and size of the pipe according to the actual situation in our home.

Through the above introduction to the installation steps of heating pipes, I hope it can be helpful to everyone in life. If you still want to know more about the Li Feng information of heating pipes, you can pay attention to Tuba Rabbit Decoration Network, China's first decoration network!

You can get it for free

Here's how to install the heating:

1.When opening the radiator packaging, be sure to carefully check whether the radiator model, color, and accessories in the packaging box are complete. Rubens radiators and other regular radiator manufacturers provide standard accessories such as air leaks, plugs, expansion nails, hooks and other free of charge.

2.Make sure to install an inlet valve and a return valve. Don't ignore them in order to save money, otherwise the radiator will not be repaired after it breaks.

3.Install the radiator in strict accordance with the installation legend. First, smash the expansion screws and hooks into the wall, install the radiators, plugs and valves with air leakage (you can pack some raw materials in an appropriate amount), then put the radiators on the hooks, and then connect the valves and pipes, and the radiator installation is successfully completed.

Precautions: a. To fix the radiator pendant, you need to use a level to correct the direction of the radiator to ensure that the radiator is horizontal and vertical, and to ensure the accurate connection between the pipe fittings and the radiator.

b. Do not open the protective film of the inner packaging of the radiator during installation, so as not to damage or scratch the paint film.

4.Pressure test: Close the main connection valve, open the radiator inlet valve, and test with pressure test equipment. The test pressure should be times of the normal use pressure, and not less than the test pressure of the entire residential pipe network. No leakage for 3-5 minutes is qualified.

Precautions for installation of heating pipes:

The pipeline installation should have a slope, if the design is not required, the slope should meet the requirements of the household heating pipe installation precautions, generally including:

1. Hot water heating and hot water ** pipelines and steam and condensate pipelines flowing in the same direction, in this case, the slope of the pipeline is generally not, and it should not be less than.

2. The slope of the steam and condensate pipeline of the reverse flow of steam and water should not be less than that.