How to solve the problem that the plastic steel window is not closed tightly, and how to deal with t

1. Check whether the closing is not tight due to the simple deformation of the sash, not the rectangular sash caused by the insufficient size of the sash.

2. Push the sash to the normal closed state, use an elastic hammer to hit the end with a gap, do not use a rigid hammer, it may break the material. It is slightly better to wrap a few layers of clothing on the outside of the steel hammer.

3. Plastic steel windows.

Due to the material, it is often deformed, you can find the unit that installed the window for you to repair it, or consult them how to deal with it, and the window will be adjusted.

4. Aluminum alloy doors and windows.

If there is a blockage or resistance when opening or closing, then we need to spend more effort when opening and closing, usually because of the following factors, the first door and window frame or sash is deformed, and the sealing strip is loose or falls off. Second, the hardware accessories were damaged. Thirdly, the installation quality is poor, and there are many deviations beyond the allowable deviation, and it is not adjusted in time.

Plastic steel windows appear can not be closed, closed tightly, closed hard, I teach you to deal with it like this, simple and practical, learned is earned, a year to save a lot of maintenance costs, please leave a message if you have suggestions, thank you friends for your support.

Shuogang windows are not closed tightly, which may be a problem with the window hinge, or it may be caused by the problem of poor sealing of the window seal.

The switch-type plastic steel window can not be closed, and it will be opened when touched, indicating that the clip on one side of the window frame is installed slightly higher, as long as the two clips on the window frame are unscrewed down, and the clamp is slightly strung downward, and the clip is re-tightened, the window can be closed.

In the figure below, this card is strung down a little bit.

Spray lubricant into the hole in the middle of the clutch, use pliers to clamp the shaft and shake it up and down left and right, as long as there is a little gap, it is much easier, and then use pliers to clamp the root of the shaft fan, clamp it, and warp it out.

If it doesn't work, knock the shaft into the fan as much as possible, and press it back with a white handle after it is in place, you can see that there is a square hole in the handle, and if there is a gap after pressing it into place, use a piece of wood to cushion the handle and then knock it inside, it should be possible to enter.

Open the window to see if the handle can be reset, if not, it should be the lock cylinder circlip stuck on the handle axis. If it can be reset, it must be caused by the deadbolt not being fully extended, and the lock groove can be adjusted.

It should be that there is a problem with the spring of the handle, and it can't be returned to the position.

Hello dear, happy to answer your <>

Answer: The reason why the upper part of the plastic steel window is not closed tightly is that the door and window frame or fan is deformed, and the sealing strip is loose or falling off. If there is bending deformation, it is easy to find, and this type of material should be resolutely not used, if the plastic steel profile is not bent and deformed, the closure is not tight, it should have nothing to do with the plastic steel profile.

After ruling out one factor, we can look for reasons in other areas. Second, the seal falls off, if the seal hardens and falls off, it can cause the closure to be not tight. You should buy high-quality sealing strips with good elasticity on the market.

If it is a profile, it is best to come with a co-extrusion sealing strip. Generally, this kind of sealing strip has high anti-aging strength, good elasticity, and is not easy to shrink or harden. However, this kind of sealing strip sometimes has a little less dimensional accuracy, but due to its good elasticity, it generally does not cause loose closure due to size and accuracy.

3. Hardware accessories reason: Hinges, lock points, lock blocks, clutches, and gaskets are the key to ensure that doors and windows are closed tightly. First of all, you must buy the hardware of a regular enterprise.

Hardware must meet national standards. The dimensional error of the hardware must be accurate within the specified range. The hardware material must meet the standards of rigidity and strength, otherwise the difference will be a thousand miles.

This is the main reason for the poor closure of doors and windows, especially in the northeast region, where large sections, large cavities, thick-walled profiles, and steel linings are also very heavy. In this way, the hardware is required to have a certain rigidity and strength. Preferably high-quality hinges with lock points.

In this way, we can ensure that the doors and windows are not opened, not deformed, and closed tightly. Fourth, installation and production: plastic steel profile cutting should be accurate, window sash accuracy should be accurate.

Before the door and window sash into the frame, check the diagonal and flatness deviation. After entering the frame, use a steel plate ruler and feeler gauge to check the lap width of the frame fan and the gap around it until it meets the requirements. Install the hardware correctly, and replace it in time if it is damaged.

The choice of gasket must be fine, often poor millimeters may cause the closure is not tight. The locking point thickness and the amount of adjustment ensure a tight close. The flatness of the sash frame is also the key to whether the closure is tight.

Wearing steel lining and welding, the rear frame and the fan should be stacked to prevent deformation. The installation should be according to the process, and the window frame and window opening should be drawn out of the center line. When the window frame is in the hole, the center line should be aligned.

The corner of the frame is temporarily fixed, and the verticality, horizontality and straight angle of the window frame are carefully adjusted, and the error should be within the allowable deviation range. 5. Finished product protection: It is very important to do a good job in the protection of finished products, and the handling and stacking should be smooth, not affected by external forces, and heavy objects should not be hung, resulting in deformation of doors and windows.

When using, it should be opened and closed lightly, which can also protect the hardware and prolong its life for staring and buriding.

Plastic steel windows are very prone to deformation when in use, resulting in more problems that plastic steel windows can not be closed, how to adjust and how to choose plastic steel windows when they cannot be closed? These are all questions that everyone is more confused about now, and then I will take you to explore the content of this.

1. How to adjust the plastic steel window if it cannot be closed.

There are several factors that cause plastic steel windows to fail to close.

1. If there is a gap when closing the plastic steel window, we can use a wooden hammer to knock on the gap at the end of the plastic steel window until the gap is closed.

2. There is an iron sheet in the gap of the plastic steel window, if the iron sheet is aging after the problem, it is easy to cause the plastic steel window to be unable to close, if it is because of this reason that the plastic steel window can not be closed, we can drop a few drops of lubricating oil on the aging iron sheet.

3. The possibility of deformation of the material of plastic steel window after a long time of use is also relatively large, and in the event of such a phenomenon, it is best for us to directly contact a professional master to help with maintenance and adjustment.

Second, how to correctly use plastic steel windows.

We should develop the habit of opening in the morning and closing at night when using plastic steel windows, the iron sheet of plastic steel windows is also easy to age when inactive for a long time, and it is best to use corner hinges when installing plastic steel windows, compared to hinges, it will be easier to adjust the hinges, and we can communicate with the master before installing plastic steel windows.

Third, whether the plastic steel window material is good or not.

1. Now many people will choose to install plastic steel windows at home, the **** of this material window is not particularly high, and the service life is relatively long, compared with other materials of windows, the advantages of plastic steel windows are also more obvious.

2. However, there are certain differences in the quality of products of different manufacturers, and the quality of plastic steel windows created by well-known manufacturers will be more guaranteed.

I concluded: the service life of plastic steel windows is as long as 20 30 years, the cost performance is very high, and there is no need to do too much maintenance and repair when using, and it is also very good to choose this material window to install.