How to paste wallpaper How to paste wallpaper?

You can post it directly. The wall should be scraped at least plaster, but after the plaster and the big white are directly pasted without the base film, the wall skin will be brought down when it is torn, and the latex paint does not know if it will be the same, but it is very similar to the role of the base film. It doesn't matter if you don't plan to change it for a long time.

The glue should be on the packaging, the ratio of powder, slurry, and water should be 1:1:1, you had better look at it again, first adjust the powder with water and then add pulp, today I see my workers do this, with only a roll of glue does not use much, a set of glue can generally paste square meters of paper 4-5 sticks, you can adjust 1 4, the general paper brush glue can be directly drawn on the back of the paper, the figure is thicker, but you have to prepare a clean towel to wipe the excess glue, if it is a long-term use of the best glue.

After measuring the ruler, you should give 25-35 cm more than the actual length, and if you need to cut the flower on the side of the flower. Now the wallpaper doesn't need to be soaked in water, and the previous paper even needs to be soaked in the pure paper of the United States.

You can go to u, some decoration forums to see, like I love my home network, etc.

After the wall is scraped and smoothed, the base film is coated, and the appropriate margin is left for the size of the flower according to the wallpaper, and the glue is evenly coated on the wallpaper. Just paste it.

The wall should be dealt with first, and then the wallpaper should be glued and pasted directly, but to paste it well, it is better to find a special master to do it. Different wallpaper pasters are different.

The steps to apply wallpaper are as follows:Tools: wall guards, buckets, glue, rulers, knives, brushes, scrapers, scissors. Stalls.

1. The former relatives will treat the wall flat and then brush the parapet.

2. Find a bucket to connect the water, stir it by hand and slowly pour in the wallpaper powder to prepare the special glue for wallpaper.

3. Measure the size of the wall and cut the paper one by one with a wallpaper knife.

4. Find a clean and flat place and brush the adjusted glue with a roller evenly on Hui Folly Tomb.

5. From the corner of the wall sticker, the wallpaper is pressed vertically pasted down, scraped evenly with a scraper, and then the excess part of the upper and lower ends is cut off.

Wallpaper is generally a worker's business, but sometimes you can't find an installer when you shop online, so you have to do it yourself.

Clause. First, measure the size of the wall.

Clause. 2. Remove the wall skin: remove the original paint, wallpaper and other objects on the wall.

If there are cracks and potholes on the wall, use gypsum powder to make up for these places, and put bandages on them after leveling; If you encounter sand-gray walls and partition walls, you should also be covered with glass silk cloth or really good cloth; Some poor quality partition walls or exterior walls need to be nailed with gypsum board to achieve thermal insulation effect.

Clause. 3. Crop the wallpaper: Measure the height from the top of the wall to the baseboard, and then cut the wallpaper.

Do not cut the flower wallpaper by about 10 cm according to the height of the wall, and use it for trimming up and down; The symmetry of the pattern needs to be considered for the flower wallpaper, which needs to be more than 10 cm, and the flowers should be cut and numbered from the top of the plan, so that they can be pasted in order. In addition, the cut wallpaper generally needs to be soaked in clean water for 10 minutes before it can be brushed.

Clause. Fourth, brush the base film scraping: brush the bottom film, evenly brush the base film on the wall, the thickness is moderate; Scrape putty and sand.

Scrape putty twice on the wall. After the putty is dried, polish the wall with sandpaper to grind off the uneven particles to make the wall smooth and flat; Paint the wall (cover paint) evenly again with a base film, without being too thick. This prevents the wall from absorbing the wallpaper glue, making the wallpaper stick to the wall and making the wall flatter.

Clause. 5. Glue: In order to ensure that the paste is firm, the back of the wallpaper and the wall should be brushed, and the glue should be evenly brushed, and the edge can not be wrapped and piled up to prevent the wallpaper from being stained.

Glue the wall 30 mm wider than the wallpaper. After brushing the glue on the back of the wallpaper, fold the glue side and leave it for 5 minutes, which can not only prevent the glue surface from drying out quickly, but also not be easily polluted.

Clause. 6. Cutting wallpaper: Measure the length before cutting, the general standard wallpaper is 10 meters long and wide per roll, and can be paved with square meters. The other two sizes are 7 square rolls and 16 square rolls.

Clause. 7. Pasteing: The principle is to first vertical and then horizontal, first up and then down, first high and then low.

When pasting the first piece of paper, find the baseline at the corner of the wall, gently flatten it with your hands from top to bottom, from the middle to both sides, and then scrape with a scraper to make the wallpaper and the wall solid. When pasting the second piece of wallpaper, overlap the overlap with the first sheet by 20 mm, use a wallpaper knife to cut off the overlapping part, remove the remaining part and scrape it flat with a scraper. It should be noted that the glue extruded from the wallpaper should be wiped with a wet towel in time to avoid the wallpaper turning yellow over time.

After scraping the putty leveling, you can paste the wallpaper.

Do you post it yourself, you'll regret it.