-
Here is a very realistic example, my father has a friend who rented out a commercial house, and there was no problem in the first few years, and then the tenant reminded him many times that there seemed to be a problem with the flush toilet in this houseBecause it is a waste of water, the monthly water bill has been on the high side, but my father's friend didn't take the issue seriously.
If there is a ripple on the surface of the toilet water, it is running water.
Later, the tenant said goodbye and directly owed more than 3,000 yuan in water bills, what is this concept? It is almost equivalent to the water bill of a normal household for several years. And what's even worse is that after discovering this problem, my father's friend didn't even remove the toilet to check the problemInstead, he only replaced a component to prevent water from running inside the toilet, and rented out the house again
As a result, it wasn't until the downstairs residents came up to them that they found out that the waste of water in the toilet was not only a problem of aging internal components, but also a failure to install it at that time. To put it simply, because the edge of the toilet drain is not waterproof, the toilet has been automatically repeating the actions of leaking, draining, leaking and drainingLater, as the damage to the inside of the toilet deepened, it not only caused the water bill to soar, but also seeped more toilet water downstairs
The roof of the bathroom is leaking.
What's more interesting is that the downstairs residents not only transformed the original bathroom into a warehouse, but also used aluminum alloy gusset in the ceiling, so that there is little attention in the space; On the other hand, the upstairs seeped down, and almost all of it was preserved in the aluminum alloy gusset of the entire ceiling. That is to say,It was not discovered until the water leakage was very serious, and the water in the aluminum alloy gusset overflowed and flowed to the goods (electronic equipment).
To sum up, when the property staff finally came up to check, they had just uncovered the aluminum alloy buckle plate downstairs, and the water flowed down like a waterfall. This shows how serious the water leakage was upstairs at that time. Long story short, just because a flush toilet didn't fit, Dad's friendNot only did it take a lot of time and energy to restore the original upstairs decoration facilities back and forth, but also finally compensated for the property damage of several thousand yuan downstairs, directly makes an originally small thing become a big thing, and the typical gains outweigh the losses!
-
Yes, a lot of our maintenance work is to solve this problem. It usually leaks down the perimeter of the drain pipe on the ground.
-
If the waterproof is not done well, it will leak.
-
Summary. Toilet leakage treatment method: 1. The internal parts of the water tank are aging, if the internal parts of the water tank are aging, there is no other choice, but you need to replace the parts quickly.
2. The connection between the toilet and the sewer pipe is leaking, if the connection between the toilet and the sewer pipe is leaking, the toilet needs to be reinstalled and the rubber is resealed. Symptomatic cracks in the toilet itself: If the toilet has cracks and leaks, it is better to replace it with a new toilet.
3. For the problem of the water inlet group and the water outlet group of the symptomatic toilet, you need to open the water tank and see that the water tank is overflowing, and the water flows out of a water pipe indicates that the water inlet group is broken, and if there is a sound of water inflow, the water outlet group is broken. 4. For symptomatic water tank leakage, you can take down the drain machine core to clean up the scale, if it still doesn't work, you need to change the toilet. 5. The bottom of the toilet is leaking, which may be due to the fact that the connecting sealing flange between the toilet outlet and the ground drain is not in place.
At this time, you need to disassemble the toilet, buy a new flange and reinstall it, and then fix the toilet with glass glue. The glass glue only plays the role of fixing the toilet bowl on the ground without moving the position, and does not play the role of draining water when the toilet drains. If the main sewer pipe drains smoothly, it will not leak out even if the flange is slightly misaligned.
Hello dear. Does this mean that your toilet is leaking?
The toilet leak is water-resistant, mainly considering the following two situations1The flange ring between the toilet bowl and the pipe is damaged, and there is a leak 2There is a leak in the sewer pipe, this situation of your home is wide, I personally think that there is a high probability that there is a problem with the flange ring connecting the toilet and the pipe, and today the old man poured a few buckets of water into the toilet, maybe the water is more urgent, and then there is a leak downstairs.
Toilet leakage treatment method: 1. The internal parts of the water tank are aging, if the internal parts of the water tank are aging, there is no other choice, but you need to replace the parts quickly. 2. The connection between the toilet and the sewer pipe is leaking, if the connection between the toilet and the sewer pipe is leaking, the toilet needs to be reinstalled and the rubber is resealed.
Symptomatic toilet itself is cracked: if the toilet cracks cause water leakage, it is better to replace it with a new toilet. 3. For the problem of the water inlet group and the water outlet group of the symptomatic toilet, you need to open the water tank and see that the water tank is overflowing, and the water flows out of a water pipe indicates that the water inlet group is broken, and if there is a sound of water inflow, the water outlet group is broken.
4. For symptomatic water tank leakage, you can take down the drain machine core to clean up the scale, if it still doesn't work, you need to change the toilet. 5. The bottom of the toilet is leaking, which may be due to the fact that the connecting sealing flange between the toilet outlet and the ground sewer outlet is not in place. At this time, you need to disassemble the toilet, buy a new flange and reinstall it, and then fix the toilet with glass glue.
The glass glue only plays the role of fixing the toilet bowl on the ground without moving the position, and does not play the role of draining water when the toilet drains. If the main sewer pipe drains smoothly, it will not leak out even if the flange is slightly misaligned.
If there is a water leak downstairs, it may be damaged by the waterproof.
Can you go downstairs and see if it has spread from the location of the side toilet?
I didn't leak out of the downstairs when I used the toilet before, and the downstairs leaked at the toilet position.
Is the toilet connected to the drain pipe straight?
-
Abstract Hello, dear.
If the toilet is not installed well, it will leak.
The more common is the position where the toilet is connected to the sewer pipe, and there may be a disturbance in the flange ring or a loose connection, which will leak.
Will the toilet leak if it is not properly installed?
Hello, dear. If the toilet is not installed well, it will leak.
The more common is the position where the toilet is connected to the sewer pipe, and there may be a disturbance in the flange ring or a loose connection, which will leak.
There is a slight stop-and-go stop on the water meter, whether the water pipe is leaking or there is air, I have also observed it for several days, the time to walk is shorter, and the time to stop is longer.
Is there a regular stop-and-go?
This situation should be a water leak, the end of the water meter is connected to the home water equipment, if there is a water leak, there will definitely be a leakage point.
Or turn off the water valve at home and look at the water meter.
If it's leaking, why stop and go, don't you keep supporting it?
Go personally think it's not a water leak.
Stop-and-go is why.
I'm sorry I don't know much about this.
-
Hello, dear. According to your problem description: There are many possible causes of water leakage, according to your description, the toilet flushing downstairs will leak, the possible causes are:
1.Blocked drains. There may be a blockage between the toilet and the drain pipe downstairs, and the water cannot flow smoothly when flushing, thus causing overflow and leakage.
In this case, you can try using a chemical destructor for unclogging or using a drain cleaner for physical unclogging. 2.Drainage pipes burst.
If the house is old, the drain pipe may have cracked or cracked, and the water will seep out of the cracked area and lead to the surrounding soil and downstairs when flushing, showing a water leakage. This situation requires the repair or replacement of the drainage pipe. 3.
Loose pipe joints. If the connection joints between the pipes are not tightly installed, water leakage will also occur. The joints between the toilet bowl and the drain need to be checked and re-tightened and tightened.
4.Damaged water leak switch or drain filler. Some toilets are fitted with leak switches or fillers to prevent water from backing up due to empty pumps, which can also occur if these parts are damaged.
Corresponding parts need to be repaired or replaced. 5.Other reasons.
It is also possible that the floor drain is clogged and the water cannot flow into the floor drain after flushing and overflows, or the toilet itself may be broken. Careful inspection is required to determine the actual cause of the water leak. In general, clogged drains and ruptured pipes are the most common causes such as.
You can do your own investigation to determine the possible cause, and it is recommended to find a professional plumber for repair work.
-
If your floor tiles don't leak, they won't affect the downstairs.
First of all, the toilet and the floor tile are two wholes, in the past, the toilet was glued to the floor tile with cement, but now many people use glass glue directly. A leak at the bottom of the toilet is a hole in the sticking of the toilet bowl and floor tiles. The leakage at the bottom of the toilet bowl should be repaired as soon as possible, and the long-term stagnant water may leak downstairs, and at the same time, the residual sewage on the ground will produce peculiar smells, and it will also affect the anti-slip function of the floor tiles; The water absorption of the wall will cause the color of the tile to sink and affect the appearance, if the wall is not waterproofed, it will also cause the other wall skin to mold, hollow or fall off!
-
Summary. Generally speaking, if the toilet tank is installed correctly, the possibility of water leakage is relatively small and will not leak downstairs. However, if the water tank itself is damaged, the quality of the pipeline is not qualified, and the installation connection is not firm, it may leak downstairs.
Generally speaking, if the toilet tank is installed correctly, the possibility of water leakage is relatively small and will not leak downstairs. However, if the key of the water tank itself is damaged, the quality of the pipeline is unqualified, and the connection is not firm, it may leak to the downstairs.
If the water leak is due to the lack of waterproofing in the bathroom or the problem of the toilet.
It should be judged according to the actual situation, if it is a leakage between the rough skin of the guard limb ballast cover, it may be that the waterproofing is not done well or there is a leakage at the pipe connection. If it's a leaky toilet, there may be a problem with the toilet itself. Hungry eggplant.
-
If the toilet leaks downstairs, you must first notify the downstairs residents to close for corresponding supplementary measures, and then report to the property and contact the maintenance personnel, and most property management companies will deal with it properly. Spine Yu can then try to determine the cause of the leakage of the toilet to the downstairs.
Under normal circumstances, there are three main reasons for the leakage of the toilet to the downstairs: the first situation may be that during the installation process, the water outlet of the toilet and the sewer inlet are not well connected, and there is a problem with the toilet rubber ring, and there is a gap in the connection that will naturally cause water leakage; The second situation is that the toilet has been used for a long time, which causes the connection to deform and age, so the water leakage occurs. The third situation is when the inside of the toilet is loose, resulting in a water leak.
The specifics of a leaky toilet.
1. The toilet installation is wrong, and there is a problem with the rubber ring in the barrel.
If there is a leak on the edge of the toilet, the first time you find it, you should scrape off the surrounding glue and loosen the bottom of the toilet. Then tilt the toilet to about 45 degrees to detect whether the rubber ring of the connection test is damaged, and in many cases there is a problem with the rubber ring of the toilet, so be sure to replace it with a new one. Finally, the toilet drain and sewer pipe are put together, and the bottom of the toilet bowl is fixed with glue.
2. Long service life, serious aging and deformation.
Some toilets have been used for a long time, and many internal parts will be aged and damaged, resulting in water leakage due to failure to work properly. You can first disassemble the toilet seat, check the parts inside the toilet, and if it is determined that the parts are damaged, you can replace the new parts; If the overall aging of the toilet bowl is severe, replace the entire toilet bowl at the end. In addition to the toilet bowl itself, which may be badly aged, the cement slab under the toilet bowl may also be damaged.
During the installation of the toilet, a cement board is constructed at the bottom of the toilet, and this cement board is mainly for waterproofing. If the cement slab is too old, it will easily break, so it will cause the toilet to leak. Therefore, in the process of maintenance, you can first pry the cement board open, discharge the cement inside the cement board, and then re-smear the new cement inside, make an anti-cement, and apply a layer of white cement on the outermost layer.
3. The toilet is blocked by foreign objects and the inside is loose.
The toilet is clogged with foreign objects, and the loose interior is also the cause of the leakage of water in the toilet seat to the downstairs. If the inside of the toilet is clogged by an object, the keys will fail and the water will leak. In general, the toilet bowl needs to be disassembled first and checked for foreign objects blocking the specific connection of the toilet.
If the specific part is damaged, then use glue to fix it.
-
Summary. Hello dear, the reasons for the leakage of the toilet: 1. The toilet was not installed when it was installed, resulting in the misalignment of the sewage outlet on the ground and the toilet drainage.
In this way, yellow water, water and foul smell will come out. 2. The installation is not professional, and the flange is not installed (the flange has a good fixing and anti-spill effect) 3. Long-term use is suitable for the loosening of the toilet and the ground. 4. The toilet toilet itself is a problem with cracks in the ceramics.
Hello dear, the toilet will leak if it is not installed.
Drain towards the ground and pour downward.
Hello dear, there will be Oh, but also to the ground leak and downward.
Hello dear, the reasons for the leakage of the toilet: 1. The toilet was not installed when it was installed, resulting in the misalignment of the sewage outlet on the ground and the toilet drainage. In this way, yellow water, water and foul smell will come out.
2. The installation is not professional, and the flange is not installed (the flange has a good fixing and anti-spill effect) 3. Long-term use is suitable for the loosening of the toilet and the ground. 4. The toilet toilet itself is a problem with cracks in the ceramics.
Hello, 5. The internal parts of the water tank are aging. 6. There is a problem with the water inlet group or outlet group of the toilet. 7. The toilet tank is leaking. Kiss, it will spread to the ground and penetrate downward.
Toilet leakage maintenance method: the water tank is leaking, and the water inlet group or outlet group needs to be repaired or replaced; The bottom of the toilet is leaking and needs to be resealed; If there is water seepage on the surface of the toilet, the toilet needs to be replaced. >>>More
1.First, use a knife to cut the glass glue at the junction between the toilet bowl and the floor tiles, and then unscrew the bolts that hold the toilet open. >>>More
First, the flushing method.
Nowadays, most toilets on the market are siphoned, which is easy to flush off the swag that adheres to the surface of the toilet. The disadvantage is that it is water-consuming and easy to block. It is not easy to clog directly and is easy to smell when it is disadvantaged. >>>More
The toilet works as follows:1. When you press the button, you pull the chain inside the toilet, so you can open the flush valve. >>>More
There are occasional surprises in the delivery drawing, so after receiving the goods, it is necessary to accept the toilet in person and confirm that there are no problems with the toilet before you can start the installation. So. >>>More