How to repair the plastic water pipe chiseled through, how to repair the PVC water pipe if it is bro

1. Observe the severity of the crack, if there is only a crack, overflow from the crack, it is simple, you can go to the hardware store at the door to buy a glue specially used to repair the cracked plastic pipe, be careful not to use the glue casually, to use a professional special glue that will not pollute the water quality.

2. If the crack is large, like a hard injury caused by a collision, if it is confirmed that it cannot be sealed with glue, you can measure the diameter of the pipe, go to the hardware store to buy a section of the joint that can just cover both ends, cut off the leakage, and glue the two ends to be glued.

Finally, as the owner, you must know where the valves are at home, not only water pipes, natural gas, heating, leakage protectors, etc., but also know that in case of accidents, you can cut off the source of danger in time!

If you have a plastic water pipe, you can use a hair dryer to blow the pipe, or wrap the water pipe with a towel, and then pour it slowly with warm water.

In winter, the climate is cold, and the water facilities are protected from freezing. For example, cotton and linen fabrics and plastic foam can be used to wrap water pipes, water meters, and faucets. At night, the windows of the kitchen and toilet should be closed, and the faucet should be slightly unscrewed to make the water in the water pipe flow without freezing.

If the water pipe is frozen, use a hair dryer to blow it, or wrap the water pipe in a towel and pour it slowly with warm water. However, it should be noted that it should never be baked over fire or boiled with boiling water, as this will cause pipes and water meters to burst.

To repair the hole of the PVC water pipe, first find the location of the hole on the PVC water pipe, according to the size of the hole, cut a section of the PVC water pipe 4-5 times wider than the hole, and cut the side, the specific operation steps are as follows:

1. Find the location of the hole in the PVC water pipe first.

2. According to the size of the hole, cut a section of PVC water pipe 4-5 times wider than the hole, and cut the side. As shown below:

3. Break the PVC water pipes to both sides.

4. After the PVC water pipe is broken, it is set on top of the hole.

5. Put a step-by-step buckle on the PVC water pipe outside the hole.

6. Lock the step-by-step fixing screws and the operation is complete.

You need to prepare a small hacksaw, PVC pipe, sandpaper, rags, bamboo joints and glue. First, use a small hacksaw to see off the hole in the PVC pipe, polish the new nozzle with sandpaper, wipe the polish with a rag, apply special glue to the nozzle, and also coat the glue in the bamboo joint, connect the port with the slub, and then apply an appropriate amount of absolute glue at the joint. Here's how:

1. Use a small hacksaw to see off the hole in the PVC pipe.

2. Use sandpaper to polish the new nozzle.

3. Wipe the polishing area with a rag.

4. Use special glue to coat the dry bush at the nozzle.

5. The bamboo joints are also coated with glue.

6. Connect the port to the bamboo.

7. Apply an appropriate amount of glue to the seams.

You can use PVC pipe fragments of the same diameter to cover the damaged part and stick it with PVC glue, that is, patching.

I changed it again, bought two directly, and a bottle of water glue,

1. You can buy waterproof tape to repair the sewer pipe, wrap it up, and then use mortar waterproofing agent and cement to wipe it on. 2. Go to the hardware store to purchase a section of joints that can just cover both ends, cut off the leakage, and then put the interface into the pipe, and use PVC glue to infiltrate and apply it to the inside of the two ends and the outside of the two sewer pipes. Sometimes check the leakage, and find that the PVC pipe is a small crack, thinking that it is enough to make up with glue, even if it is repaired, when the water pressure is large, there will be water leakage, it is best to change a section of the pipe.

3. When the PVC pipe leaks at the elbow or joint port, it is best to ask professional personnel to prevent water leakage. Sometimes it is found that the PVC pipe leaks at the elbow or joint port, which is very difficult to repair and prevent water leakage, and it cannot be dealt with by yourself. It is best to use professional personnel to prevent water leaks.

Additional Information: Product Benefits:1

The surface hardness and tensile strength of the pipe are excellent, and the safety factor of the pipe is high. 2.It has good aging resistance, and the normal service life can reach more than 50 years.

3.The pipeline has excellent corrosion resistance to inorganic acids, alkalis and salts, and is suitable for industrial sewage discharge and transportation. 4.

The friction coefficient of the pipeline is small, the water flow is smooth, it is not easy to block, and the maintenance workload is less. 5.The material has a high oxygen index and is self-extinguishing.

6.The expansion coefficient of the pipeline line is small, and the deformation is small due to the influence of temperature. The thermal conductivity and elastic modulus are small, and the ice resistance is excellent compared to cast iron drain pipes.

7.Pipe banquet spring, pipe fittings can be used for bonding, the construction method is simple, the operation is convenient, and the installation efficiency is high. 8.

Good water tightness: The installation of PVC-U pipes, whether they are connected by adhesives or rubber rings, has good water tightness.

The method of filling the leakage of the plastic water pipe is as follows:

1. Small water leakage: directly buy plastic for repairing water pipes, and then use a special plastic spray gun and plastic welding rod to make up for it.

2. Sewer pipe leakage: buy a new water pipe according to the material of the original water pipe to connect the leaking part, if it is a PVC water pipe, you can buy a few PVC water pipes to connect it yourself. Cut the broken pipe first, and put the interface into one end of the pipe first, so that the cutting position of the other end is exactly flush with the other opening of the interface.

The rest

First of all, we have to close all the water valves, and then wipe the leaking place with a dry cloth to check where the water leak is, if the leakage is not particularly serious, we can directly buy special plastic for repairing water pipes, and then use a special glue gun plus plastic strips. Beat the glue on top of the water pipe and wait until it has dried before using water.

If there is a leak in the sewer pipe, then we still recommend buying a water pipe with the same sewer pipe to replace it, if it is not a PVC water pipe, then we recommend replacing it with a PVC water pipe, which can be connected by itself. Cut off the broken tube first, then pull the tube out, and put the new tube into the state of detection.

Leaks in plastic water pipes can be filled in this way:

1. If the leakage of the plastic water pipe is caused by cracks in the pipeline, and the cracks are relatively small: you should first turn off the water inlet valve at home, then use a rag to dry the water stains on the surface of the plastic water pipe, and then wrap a few circles of raw material tape around the crack position, and put some foam glue on the surface, and finally wrap a layer of waterproof paper on the surface.

2. If the crack on the plastic water pipe is very large: the plastic water pipe at the crack position should be cut off, and then the new plastic water pipe of the same specification and model should be connected, and the inner wall and outer wall of the nozzle at the connection position need to be coated with some PVC glue, and then use a new joint to firmly connect the old and new water pipes together. If the plastic water pipe has burst, you must ask a professional to come and help you deal with it.

Advantages of plastic water pipes:

1. Good chemical stability, not affected by environmental factors and medium components in the pipeline, and good corrosion resistance.

2. The thermal conductivity is small, the thermal conductivity is low, the thermal insulation is insulation, and the energy-saving effect is good.

3. The hydraulic performance is good, the inner wall of the pipeline is smooth, the resistance coefficient is small, it is not easy to accumulate fouling, the flow area in the pipe does not change with time, and the probability of pipeline blockage is small.

4. Compared with metal pipes, the density is small, the material is light, the transportation and installation are convenient, flexible, simple and easy to maintain.

5. It can be naturally bent or the bridge is slow and wide, and it has cold bending performance, and the coil supply method can be used to reduce the number of pipe joints. <>

When it comes to plastic pipes, I believe everyone is familiar with them, it is an indispensable building material product in our lives, but after a long period of use, water pipes will also leak. So how to repair a leak in a plastic pipe? What should I pay attention to when choosing a water pipe?

How to repair the leakage of the plastic repentant pipe:

Depending on the specific situation, first of all, the water pipe leakage is small, and it can be repaired directly with plastic strips; Secondly, if the sewer pipe is leaking, the leaking pipe can be cut, a pipe of the same model can be replaced, and PVC glue can be coated at the junction of the water pipe; Finally, the water pipe joint is loose and leaking, first tighten it with a tool, but it still doesn't work, you can only replace the new water pipe joint of the same specification, and apply waterproof glue, etc.

How to choose a household water pipe:

1. First of all, it is best to choose a new type of water pipe, the material is PPR pipe, which is not only green and environmentally friendly, but also the water pipe and the interface are connected together, there will be no water leakage, and it is also very affordable. However, when choosing, in order to avoid buying inferior products, it is recommended to cut off a small number of samples and use fire to judge the quality of the product, generally it is better to burn a water pipe without black smoke.

2. Then in the process of choosing the diameter of the household water pipe, it is necessary to choose according to the size of the inlet water pipe, if the inlet pipe is 6 pipes, choose 6 pipes or 4 pipes according to the size of the water consumption at home. At the same time, friends with conditions can buy hot water pipes in a unified manner, and the performance will be better.

3. Finally, do not choose a semi-transparent water pipe, otherwise in long-term use, the algae in the water pipe will multiply due to photosynthesis and affect the water quality. In addition, the accessories of Bihe water pipes, such as valves, interfaces and other small parts, are best purchased in sets, consistent with the brand of water pipes, otherwise it will affect its dense and sensitive sealing, resulting in water leakage and other situations.

Summary: The above is for you to introduce how to repair the leakage of plastic pipes and how to choose the relevant content of household water pipes, I hope to bring help to friends in need, if you need to know more about related knowledge in the later stage, welcome to pay attention to Qeeka Home.

As we all know, plastic pipes are indispensable building materials in home decoration. So the question is, how to repair the leakage of the plastic pipe? What should I do if a plastic water pipe breaks? Next, let me give you a brief introduction to the relevant knowledge of plastic pipes.

First of all, use a saw to see off the leaking part, and then use sandpaper to polish the saw edge; Secondly, wipe the saw edge clean with a rag and use glue to apply it to the inside of the saw edge and the "bamboo slub"; Finally, the saw is attached to one end of the "bamboo" and the other end is glued in the same way to ensure that there is no leakage.

What to do if a plastic water pipe breaks.

1. First of all, you should close the tap water valve in time, and carefully observe the specific leakage part until you find out the specific cause of the leakage.

2. Secondly, check the degree of rupture of the plastic pipe, if it is only a slight crack, and it is overflowing from the crack, the treatment method is very simple, you just need to go to the building materials store to buy the glue specially used to repair the plastic pipe. However, it is important to note that you should never buy glue at will, but should use a special glue that will not affect the water quality.

3. Of course, if the cracking degree of the plastic pipe is more serious, such as the cracking caused by the collision, then in the case that the glue cannot be repaired, you can measure the diameter of the pipe first, and then go to the building materials store to buy the appropriate size of the water pipe joint, and cut off the leakage, only need to bond the two ends to use normally.

4. In addition, through observation, it is found that the plastic pipe can no longer be repaired, so the entire section can only be replaced. Of course, if this is beyond your ability, then you can only find a professional repairman to help deal with it.

Summary: After reading the above introduction, I believe you have a further understanding of how to repair plastic pipe leakage. If you need to know more about it, please continue to ******, and more exciting content will be presented to you in the future.