Is the polished tile easy to clean, and how to drag the polished tile to be clean?

Mopping tips.

1.Fill a bucket of warm water before mopping the floor, add a little salt and stir it in the bucket, put the mop in the bucket and stir it, wring the water before taking out the mop, mop the floor in order, make sure that the watermark is dry while you mop the floor, and the tile floor is shining, the same as the newly laid floor.

2.Multi-purpose foam cleaner if the floor is a little dirty, and the dirt of the floor is a little greasy. Then use a multi-functional foam cleaner, spray evenly on the stained areas, wait for 1 5 minutes, let the multi-functional foam cleaner completely dissolve the stains, and mop it clean with a wiping mop.

3.Tile descaler, for tile crevice stains, especially those that are difficult to clean, spray evenly on tile crevices. Wait for 1 5 minutes after the tile descaler has completely dissolved the stain, wipe the mop and it will be clean, and then wipe it again with clean water, and the tile floor will be as clean as new.

1. The current ceramic tiles, except for some antique tiles, other polished glazed tiles will have a watermark after wiping the floor with a mop. This simple treatment method is to say that the mop is wrung clean, and it is best to use a mop that can be rotated and dried, the mop has a low moisture content, and there will be fewer watermarks on the ground. Nowadays, there is almost no water seepage in the tiles, so it is easy to have a watermark if there is water.

2. Wipe with a damp cloth and wipe with a mop with a certain moisture. Generally, use a watering can, spray a certain amount of water on a dry mop, and then wipe it, generally spraying it in the center area of the mop, surrounded by a dry cloth, this kind of wiping, the watermark on the ground is relatively less, and it is relatively clean.

3. In addition, it is to push and vacuum cleaner with ground, and the area that is basically dirty in the home is the kitchen and bathroom, and most of the other areas are dusty. A wet mop cleaning every two or three days is sufficient. You can also scrape the ground to hang the water clean.

4. The commonly used method in the office building of the shopping mall is to apply oil to the ground to be clean and bright. The function of oil is to brighten, but it is easy to absorb dust and is not easy to clean.

5. In addition, use tile cleaner or oxalic acid in a mop bucket, and wipe the watermark with a dry mop cloth after wiping it with a wet mop.

Clean the polished tiles.

It's very simple, if it's just dust, wipe it with a towel lightly and it's clean, if there are stains or something like that, use a wet mop to mop it again, and then drag it with a dry mop, if the brightness of the tile is low, you can restore the luster by waxing the tile. However, if you want to be more specific, you still have to go to the tile store to consult, like I went directly to QD tile consultation before, and their staff attitude is also very good.

Polished tile is a kind of tile that most people will choose when decorating, because the effect of his decoration is very good, so it is loved by many people. What to do if polished tiles penetrate stains? If the tiles penetrate into the house, it is difficult to clean, so we have to find a more professional way to do it.

Polished tile is a kind of tile that most people will choose when decorating, because the effect of his decoration is very good, so it is loved by many people. What to do if polished tiles penetrate stains? If the tiles penetrate into the house, it is difficult to clean, so we have to find a more professional way to do it.

To avoid harming the tiles, we also need to understand how to clean the house on the polished tiles.

What to do with the stains that penetrate the polished bricks

There is no good way to remove the stains that penetrate the polished brick, so the stains must be dealt with in time, otherwise the polished tiles can only be replaced.

The surface of the polished tile is polished, and it is generally difficult to remove the stain if it penetrates into the tile, so it is necessary to remove the stain in time to avoid the stain from penetrating into the tile. Vitrified bricks will be exposed after grinding, oil, dust, etc. are easy to penetrate, and the vitrified bricks that have not been treated with antifouling treatment should be waxed in use, and in order to avoid damage to the brick surface during construction before paving, the brick surface should be covered with woven bags and other items that are not easy to decolorize. Antique bricks and wall tiles can be removed with a few small tricks if stains penetrate.

How to clean stains from polished tiles

1. Tea stains, fruit stains, coffee sauce vinegar, leather shoe prints and other stains use sodium hypochlorite diluent (bleach), soak for 20-30 years and wipe off some stains that have penetrated into the brick for a long time, and the soaking time is several.

2. Use sodium hypochlorite dilution (bleach) to deform the mold spots deformed by ink and antifouling wax mold. When using, just apply bleach to the stain, soak it a few times, and wipe it off.

3. Use hydrochloric acid or phosphoric acid solution for cement, scale, rust and rust spots, and wipe it several times.

4. Use alkaline detergent or organic solvent (acetone, triethylene) for paint, oil, oily marker, and surface antifouling wax layer, and paint and degreasing agent.

5. How to use the rubber hammer mark for decontamination: first soak it in 20-40 sodium hydroxide (NaOH) solution for 24 and wipe it with a cloth, and then soak it in 30-50 hydrochloric acid (HCl) solution for 30 and wipe it with a cloth.

6. Ice cream alkaline cleaner.

7. Lime scale acid cleaner.

What about the stains that penetrate the polished tiles? There is no good solution to this problem. The most direct way, the most labor-saving way, is to replace the polished bricks.

As for how to clean the stains on the polished tiles, there are more cleaning methods for this one, we give different cleaning methods for different stains, there are a total of seven aspects above, you can take a good look.

Ceramic tile is our more common building materials in decoration, the use of a wide range of ceramic tiles, there are many types of tiles, polished tile is one of them, the following will tell you about its advantages and disadvantages and cleaning methods.

First, the advantages and disadvantages of polished tiles.

1. Advantages. Polished bricks are thin, do not add weight to the building, and are easy to pave. Natural stone due to the time of diagenesis and the different color difference of the depth of the rock layer will be relatively large, and the polished brick is carefully blended, the color of the same batch of products are the same, basically no color difference.

Moreover, the polished brick is pressed by thousands of tons of hydraulic presses, and then sintered at a high temperature of more than 1200 meters, so the strength is high. At the same time, because natural stone is a mineral, it has not been sintered at high temperature, and long-term contact will be harmful to the human body. Laughing but polished tiles are different, after high temperature firing, they will not produce elements harmful to the human body.

2. Disadvantages. The disadvantages of polished tiles are very obvious, that is, they are easy to get dirty, not resistant to dirt, and after using a cloth to drag, there are usually traces of water, and it is more troublesome to wipe it clean. There is also an obvious disadvantage of polishing bricks, that is, they are too smooth, so they do not have anti-slip ability, and once there is water on the ground, it will be very slippery.

Therefore it is not very suitable in these places such as bathrooms and kitchens.

Two. Polished tiles of the clear.

Cleaning method. 1. Bleach.

Tea stains, fruit stains, coffee sauce vinegar, leather shoe prints and other stains use sodium hypochlorite diluent, that is, bleach, and wipe them with a cloth after soaking for 20-30 minutes when using; Some stains that have been infiltrating the brick for a long time can be soaked for several hours. Bleach can also be used for mold spots formed by mildew in inks and antifouling waxes. To use, simply apply bleach to the stain, soak it for a few minutes, and wipe it off.

2. Soapy water.

Soap is a very convenient cleaning product, it is not only practical, but also very close to the people. When cleaning the polishing tiles with soapy water, you can add some pine oil to mix, which will make the polishing tiles clean and shiny.

3. Decontamination cream.

After using it for a long time, there will inevitably be some stains left in the gaps of the polished tiles, so you can use a stain remover to remove them, and the stains can be cleaned up.

Polished brick is relatively light, so it will not increase the weight of the building, and it has the advantages of small color difference, environmental protection and health, but it is not resistant to dirt and non-slip, so we should pay attention when choosing the place to use, at the same time, we also listed some cleaning methods for polished tiles on it, hoping to provide banquet help to friends who have polished tiles at home.