What should I do if there are gaps in the laminate flooring? Is there a remedy?

Laminate flooring.

One of the main causes of the gap: unilateral expansion of the laminate flooring caused by ventilation at the junction of the moisture-proof film.

When laminate flooring is installed, the connection of the moisture-proof film is not tightly glued with waterproof tape, and one side of the laminate floor is on top of the moisture-proof film, and one side is at the joint of the moisture-proof film. Because the connection of the moisture-proof film is not tightly glued with waterproof tape, the moisture channel invades and causes the edge of one side of the laminate floor to become longer, and the length of the two long sides of the laminate floor is unequal, so that the end of the laminate floor produces a triangular seam. Therefore, when installing the moisture-proof film, the laminate floor must be tightly glued with waterproof tape to ensure that it is not breathable and can avoid the occurrence of gaps in the laminate floor.

The second main cause of the gap in laminate flooring: the installation quality problem of laminate flooring Laminate flooring installation.

Due to the uneven force during installation, the laminate floor produces triangular gaps, and the triangular gaps and side gaps can be eliminated by tightening the laminate flooring on both sides of the gap. Laminate flooring.

The third main cause of the crevices is improper humidity control.

When the room is uninhabited for a long time, if the indoor humidity is not adjusted in time, the laminate floor shrinks and produces cracks or arching. Therefore, if the room is uninhabited for a long time, you can put a basin of water indoors to adjust the indoor humidity.

There is a gap in the butt floor, don't worry, five tricks to solve it for you, it is very practical.

How to deal with gaps in laminate flooring? As a newbie to flooring installations, you may not know much about this. But don't worry, let me give you a brief introduction.

1. Mix old newspapers and alum:

If the floor gap is small and repairable, then we can fill the gap with old newspapers and alum. Cut the old newspaper into small pieces, then mix with an appropriate amount of alum, and stir the mixture into a paste with water or rice broth. In this way, we can use the paste to fill the gaps in the floor, and use a knife to fill the paste into the joints, and then smooth the surface, and wait until the natural shade has dried on the floor and the floor can be used normally.

Of course, it is also possible to use pigments that are close to the color of the floor to ensure the aesthetics of the restoration.

2. Apply a new adhesive

If the floor gap is large due to non-standard installation, we need to remove the floor with gaps, and ensure that the floor surface is not damaged during the removal process, and then clean up the old adhesive and ash, apply new adhesive, and finally re-lay the floor. Of course, during the installation process, the floor must be compacted to ensure the tightness between the floors and prevent the recurrence of gaps.

3. Re-paving:

If the gap in the floor is very large and the surface layer is damaged due to moisture, in the case that neither of the above methods is applicable, we can only remove all the gaps in the floor first, and throw it away, and install the new intact floor.

Of course, we must pay more attention to the process of re-laying the floor, and the connection part of the moisture-proof film should be densely packed with waterproof tape to prevent moisture from entering and causing gaps in the floor to appear again.

Summary: After reading the above introduction, I believe you have a further understanding of how to deal with gaps in composite flooring. If you need to know more about it, please continue to ******, and more exciting content will be presented to you in the future.

In fact, when the gap in the floor is very small, you don't have to worry too much, at this time, you can also choose to buy a carpet and put it in the place where there is a gap. This is not only very aesthetically pleasing, but also prevents the gap from getting bigger and bigger. The reason why there are gaps in the floor may also be related to the fact that the room is too wet.

And in the process of using the floor, we must do a good job of maintenance. And when wiping the floor, don't use too much detergent, which will also cause damage to the floor.

You can first sandpaper sanding, and then buy the same material of the floor to fill the gap, or you can use glass glue to fill in; I think it can be repaired, and a special renovation worker can be hired to repair it.

If there are cracks in the floor, the main thing is to see what kind of material the floor is made of? If there are cracks in the wooden floor, you can find a decorator to come and repair it, and if there are cracks in the tiles, you can use some beauty joints to hook it.

You can find some relevant workers. Buy some restoratives, you can get a good repair, and you can also fill it in life. Alum is a very good choice.

If you encounter such a situation, you can lay a layer of floor tiles on it, which will look more beautiful and the quality is better.

Remedies for laminate flooring cracks: If the total area of the surface paint film cracking is small, then it can be moderately painted and polished and waxed; However, if the total area is relatively large or the condition is more serious, then the only way to do this is to polish it and then apply the paint. Here's how:

First, use an abrasive cloth to gently polish and polish the damage to eliminate the stains, continue to use a dry thin cloth to scrub neatly, and do the coating again or paste the polyester film. For wood floors with light cracking, some compounds can be used to fill the gaps; If the crack is stronger, then the only solution is to replace the part that has been cracked. If the gap between the wooden floors is more than 2mm, then it is necessary to carry out maintenance and solve the problem.

In more serious cases, all the wooden floors must be dismantled, and part of the wooden floors must be resurfaced and replaced according to the condition.

Precautions: The first thing to pay attention to is how much the bottom layer of the problem, because we pave the wooden floor, then the wooden floor can not have the uneven situation, at the time of paving the parquet to pay attention to the inquiry, the wood floor must be located within the scope of ability, how much difference can not be higher than 3mm spacing, otherwise it will be very easy to have a gap, so that the water will be thrown from this gap, so that the parquet is very easy to cause problems, Then the question of competence in the case of wood flooring becomes crucial.

The second is that the spacing between the parquet and the surrounding walls must be noted, the parquet and the general floor tiles have completely different differences, that is, the parquet will have a telescopic variant, in order to better prevent that situation from coming in time, and the parquet must leave a gap in the process of assembling with the surrounding walls, so that there can be space for the parquet to have a telescopic situation. The gap between the parquet and the surrounding wall should be within the standard range of 10mm-12mm.

If the gap in the floor is not large and can be repaired, then you can choose to use old newspapers and alum to fill the gap. The old newspaper is cut into tiny pieces, then mixed with an appropriate amount of alum, and the mixture is boiled into a paste using water or rice broth.

If the cracks of the composite floor are relatively large, the old adhesive and ash can be removed, the new adhesive can be applied, and the installation and paving must be carried out again.

You can apply some glue first, and then sand it will be fine. Pay attention to the way you repair it, but also pay attention to the glue used. It is also necessary to pay attention to waterproofness, but also to moisture resistance, and also to the process of repairing.

It can be filled with glass glue, or it can be filled with gypsum powder mixed with a certain amount of paint, or it is also possible to directly re-lay the floor; When using glass glue, don't put too much at one time, and wait for it to solidify, and the excess glue must be cleaned up in time.