How should hot and cold faucets be installed?

The installation of single-hole basin faucet should pay attention to the diameter of the water outlet when buying a single-handle basin faucet, most of the water inlet on the market is a hard pipe, pay attention to the height of the reserved water pipe, and it is best to go down about 30 from the basin. When installing, a special angle valve must be selected, and the angle valve must be fixed with the cold and hot water pipe of the wall water. If there is a distance between the angle valve and the faucet water pipe, you need to purchase a special pipe to lengthen the link.

Do not use other water pipes to connect, otherwise it will leak and fall off due to high water pressure. If the inlet pipe is too long and exceeds the outlet pipe, just cut off the excess and leave it undivided. Note:

Before installing hot and cold water faucets, do not hard-bend the water pipes to 90 degrees or more than 90 degrees. When installing the basin to drain the water, do not forget to buy a small connector (short to the faucet). Before installation, the installation of the water pipe buried in the wall must be flushed in advance, and the installation of the shower and bathtub faucet If you buy a shower, bathtub, and wall-mounted faucet, you need to choose the right height to bury the water pipe.

The distance between hot and cold water pipes is about 20 miles or more.

Rinse the water pipes before installation to avoid damage to the faucet due to the hard water quality. Concealed shower and bathtub faucets: After purchasing concealed faucets, the valve core of the faucet should generally be embedded in the wall.

The thickness of the bathroom wall should be considered before embedding. If the wall is too thin, the spool will not be able to be buried. Do not easily remove the plastic protective cover of the valve core when it is buried, so as not to damage the valve core with cement and other chores during the embedding.

In addition, when the valve core is embedded, you should also pay attention to the direction of the valve core up and down, left and right, so as to avoid the valve core being buried wrong.

In the case that there are multiple hot water outlets that need hot water, the hot water outlet end of the water heater is divided into several (there are several hot water outlets) tee, if it is a newly renovated house, you can ask a water and electricity installer to pre-bury the hidden pipe in the wall, if it is an old house, the requirements are not high, and the installation of open pipes is OK. After installing tee, you can divert hot water to where you want to use it, including kitchens, washbasins, and other places that need hot water! As for the need to use the hot and cold water faucet to control the start of the water heater, as long as you turn on the electricity (or battery) ventilation, at any hot water outlet, turn on the faucet, and the gas water heater will automatically start!

As for the installation of the mixing valve, there is no contradiction with the water heater, the mixing valve has two interfaces, the left side is connected to the hot water, and the right side is connected to the cold water (in fact, there is no difference between left and right, but it is just customary) After installation, the mixing valve is biased to the hot water end (left) to start the water heater! If the water is hot, turn to the right a little more, and you're good to go!

Hot and cold water faucets are convenient to use, and for this they need to be installed in place. How to install the hot and cold water faucet? PChouse will take you to find out.

Before installing, prepare the tools you may want to use. Commonly used tools: wrenches and waterproof tape; In addition, it is necessary to check whether the supporting parts of the hot and cold water faucet are complete.

When installing the hot and cold water faucet, you should first organize the accessories and make sure that the instruction manual is matched correctly. First of all, connect the two inlet pipes of the cold water pipe and the hot water pipe to the corresponding water inlet of the hot and cold water faucet horse respectively, and then after the connection is complete, the fixed column of the cold and hot water faucet is threaded into the two water inlet pipes to ensure that the correspondence is correct. Once this is done, the assembled hot and cold water faucet can be installed on sinks, washbasins, etc.

Preferably, fix the farrier sheet of the hot and cold water faucet and tighten the screw nut.

1. It is the first choice to sort out all the accessories of the hot and cold water faucet. Tighten the main water valve until no water comes out of the faucet;

2. Connect the cold and hot water pipes to the water inlet respectively;

3. Fix the faucet and let it be tightly connected to the water inlet pipe;

4. Connect the faucet to the basin;

5. Hold the horseshoe sheet firmly and tighten it with screws.

Hot and cold water faucet installation** is as follows:Tools: Four Seasons Muge hot and cold water faucet, water inlet pipe, horseshoe sheet, screw, nut.

1. Sort out all the accessories of the hot and cold water faucet and check that there is a reference manual for the manual.

2. Connect the two water inlet pipes to the water inlet of the hot and cold water faucet.

3. After connecting, thread the fixed column of the cold water faucet into the two water inlet pipes.

4. After everything is done, install the cold town hot water faucet on the basin, and put an opening in the basin into the water inlet pipe.

5. Finally, fix the horseshoe sheet and tighten the screw and nut.

<>2. First connect the two water inlet pipes to the water inlet of the hot and cold water faucet, as shown in the following figure

3. After connecting, thread the fixed column of the hot and cold water faucet into the two water inlet pipes, as shown in the following figure

4. After that, fix the horseshoe sheet and tighten the screw nut, as shown in the following figure

5. Then one of the two water pipes is responsible for hot water and one is responsible for cold water, as shown in the figure below