The wall has been waterproofed, how to paste tiles to make it stronger?

Combination cut tile can be more firm, simply put, is to paste the tile without hollowing and cement to produce the maximum area of contact, a reasonable grasp of the ratio of sand and cement is to maximize the degree of adhesion, so that the brick will be more firm.

In the case of tiling, it is divided into two kinds, one is floor tiles, one is wall tiles, floor tiles and wall tiles have different requirements for tiles, for these two, we are separated.

First of all, the floor tiles, the hardness requirements for the tiles will be relatively high, because the contact is heavy, the need for strong friction resistance, good waterproofness, but relatively high, but in order to prevent the later quality is not good, fragmentation, buy more expensive, some of the best is still worth it, usually in the case of paving floor tiles, will use dry paving and wet paving, but the most basic principle is not to appear hollow phenomenon, And it is best to use the brushing process to increase the contact area of the tile and the mortar, to apply tile adhesive on the back of the tile to the tile after paving the tile can prolong the bonding life of the tile, and to maintain a distance of at least two millimeters between the tile and the tile, the situation of thermal expansion and cold contraction of the tile due to uneven heating should be could, if the gap between the tiles is too small, the situation that the backlog of bricks will be broken and the top brick will occur because of the thermal expansion and cold contraction of the tile in the later stage, which will bring great trouble to the maintenance in the later stage.

Wall tiles are relatively speaking. The strength requirements for the tile are not so high, but, for the size of the wall tile, it is required to use the size as much as possible, the specification is smaller, such as 30 60, so as not to fall off because the tile is too large and the weight is too large in the later stage, resulting in the occurrence of falling off. The distance between the tiles should also be kept at least two millimeters to allow room for the hot expansion and contraction of the tiles.

Finally, it is worth noting that regardless of paving floor tiles or wall tiles, it is best to use the beauty seam process to fill the gaps of the tiles, especially the bathroom wall tiles, and the floor tiles should be beautiful seams, so that the waterproofing of the wall and the ground in the later stage can play a good role, prolong the service life of the tiles, and also play a good role in the protection of the exterior wall

The tiles should be soaked overnight in a basin of water before being applied. You can also spray some water after the tiles are pasted, so that it will be particularly firm and not easy to hollow.

When pasting tiles, you need to remove some dirty things on the surface first, and then choose some glues with strong pasting ability.

Before pasting tiles, the wall should be smoothed, and then sprayed with some water on the wall, and then tiled, after the tiles are pasted, you can also soak them in water, so that it will be very firm.

You can apply another layer of wall paint on the wall, so that it will be more firm and convenient when you go to paste tiles.

The use of traditional cement and sand for pasting, can also be used with special porcelain tile sticking material, these two kinds of tiles can save manpower, and the lamination ability is also relatively strong, is a very suitable tile.

1.Clean the back of the tile, keep the back of the tile clean and dust-free, and scrape the tile adhesive when it is dry.

2.Tile adhesive mixing water ratio: 25 kg of tile adhesive plus about 6 kg of water, tile adhesive stirring evenly, wait for about 5-10 minutes and then stir, you can build paving, stirred tile adhesive to be used at one time, not used up tile adhesive can not be left to the next use, indirect time will be dry and solid can not be used.

3.Use a toothed scraper to scrape the tile glue on the wall, scrape the tile glue must be scraped evenly, scrape the area according to their own tiling speed to grasp, after scraping the tile glue, the tile must be on the wall within 15 minutes, and the tile is kneaded and flattened.

4.The back of the tile is also scraped with a toothed scraper, and the tile glue is scraped into a toothed shape.

Nail free adhesive is an adhesive that provides the greatest possible alternative to nails without the need for surface drilling to fix and bond materials such as wood, plastic, glass, cement, ceramics and metal.

It is better to use a mixture of tile adhesive and cement for pasting, which is more firm.

We should use tile adhesive, which needs to be treated before use, which will increase the construction cost but is the best way to make the tile firm.