How to use glass glue How to use glass glue

The use of glass glue is as follows:1. Do a good job of cleaning: Before gluing the glass glue, it is necessary to remove dirt, dust and other dirt from the surface of the joint.

Clean the surfaces of the two objects that need to be glued and keep them dry. The interface surface is then covered with plastic tape to ensure a perfect seal and neat lines.

2. Specific bonding: cut the nozzle, install the needle-nose tube, and then cut at a 45-degree angle according to the size of the joint. Finally, a caulking gun is installed, squeezing the rubber at a 45-degree angle along the gap to ensure that the rubber and the substrate surface are in close contact.

When the seam width is greater than 15 mm, the glue must be applied repeatedly. After gluing, trim the surface with a knife to remove excess glue, and then remove the tape. If any stains can be removed with a damp cloth.

3. Glass glue pasting time and curing timeThe curing process of glass glue develops from the surface inward. Silica gel with different properties has different surface drying and curing times. Therefore, if the surface is to be repaired, it must be done before the glass glue dries.

1. Press the switch on the back of the glue gun with one hand and pull out the bolt with the other hand.

2. Use scissors to cut the glue outlet on the top of the glass glue. Do not cut the threads when cutting.

3. Screw the glass nozzle onto the cut glue outlet.

4. Put the glass glue with the glue nozzle screwed into the glue gun, press the switch behind the glue gun, push the gun bolt forward, and fix the glass hose.

5. Aim the glue nozzle at the position where the glass glue needs to be beaten, pull the trigger of the glue gun hard, and inject the glue to the desired position.

6. Finally, use a scraper to scrape the beaten glass glue flat and modify it evenly. After the glass glue is beaten, it generally takes 1 hour for the surface to be glazed. It takes 24 hours to dry, during which time it is best to hold the item in place by other means and not shake it.

The steps for using glass glue are as follows:Tools: glass glue, glue nozzles, scissors. 1. Prepare a glue mouth and cut it diagonally, the incision should not be too large, and it should be moderate.

2. After loading it into the inside of the glue gun, then put the glue nozzle on.

3. After aiming and squeezing into the gap, aim at the place where the glue needs to be glued, and squeeze it horizontally.

The use of glass glue is as follows:

1. You need to press the switch behind the glass glue gun with one hand, and pull out the bolt with the other hand at the same time.

2. After that, you can use scissors to cut out a small hole in the glue mouth of the glass glue. It is possible to cut the thread, and at the same time, the glue nozzle of the glass glue should be screwed on the top of the glue outlet.

3. Then you need to put the glass glue into the glue gun and press the switch behind the glue gun to fix the glass hose.

4. After fixing, you need to align the glue to the position where you need to use the glass glue, and then you need to use a scraper to scrape the glass glue flat. You can follow the above process to operate, the operation method is relatively simple, and the use of glass glue is also very good.

Precautions for the use of glass glue

1. When using glass glue, try to pick a location with better ventilation effect, and open the windows at home after use. In this way, the harmful gases emitted by the glass glue can be dissipated faster and will not cause harm to the human body.

2. Avoid touching the glass glue ** or entering the eyes, so when using the glass glue. It is best to wear gloves and use a protective shield to prevent the glass glue from getting into the eyes.

3. When using glass glue, it is also necessary to wear a mask, which can well prevent harmful gases from entering the respiratory tract and better protect personal safety.

4. After the use of glass glue is completed, we must pay attention to sealing, if it is not sealed well, it will affect the service life of glass glue. And when placing the glass glue, try to place it in a position that is not easy for children to touch.

Steps for using glass glue:

1.Press the switch on the back of the glue gun with one hand and pull out the bolt with the other hand;

2.Use scissors to cut the glue outlet at the top of the glass glue; Do not cut the threads when cutting.

3.Screw the glass nozzle onto the cut glue outlet;

4.Put the glass glue with the glue nozzle screwed flat into the glue gun; Press the switch on the back of the glue gun, push the bolt forward, and fix the glass hose;

5.Align the nozzle with the position where the glass glue needs to be beaten; Pull the trigger of the glue gun firmly to inject the glue to the desired position;

6.Finally, use a scraper to scrape the beaten glass glue flat and modify it evenly; After the glass glue is beaten, it generally takes 1 hour for the surface to be glazed. 24 hours to dry; During this period, it is best to use other methods to secure the relevant object and not shake it;

Step 1: First, clean your hands and use a trimming tool to remove the dead skin on your ten fingers. Next, coat with primer and let dry.

Step 2: Take out a piece of scotch tape, it is recommended to choose a matte white transparent one, use the prepared nude nail polish, and evenly apply it to the non-sticky side of the glass tape. step 3：

Cut off the section of scotch tape you've applied and use scissors to cut a moderately wide strip (about one, discarding uneven parts on both sides). Step 4: With the help of eyebrow clips, paste the cut transparent tape diagonally on the nails.

Step 5: Cut off the scotch tape that grows out. step 6：

In different directions, paste the nude transparent tape in turn, and finally apply a layer of polish.

Glass glue is divided into: acidic neutral, generally selected at home, so that the taste is less, generally to assist in bonding and filling gaps. The glue gun is an iron frame with a screw handle, the glass glue barrel is installed, tightened from the back, and the front can be the basic glue.

Depending on what you use it for, it is generally used with a glue gun.

Glass glue is divided into: acidic neutral, generally selected at home, so that the taste is less and the corrosion is light. For example, if you stick to the mirror, you must use neutral, otherwise you will spend a lot of face.

It is generally used to assist in bonding and filling gaps. The glue gun is an iron frame with a screw handle, the glass glue bucket is installed, tightened from the back, and the front can be the basic glue.