How long after rubbing the toilet can I take a shower? What should I pay attention to when playing g

The back of the toilet bowl can be covered with glass glue to prevent stains from being deposited on the bottom of the toilet. The best way to deal with it is to glue around the toilet bowl to fix the position of the toilet, and the surface will dry for 2 hours and thoroughly for about 48 hours before taking a bath.

After two days, you can take a shower. It is necessary to pay attention to the use of the toilet, not to produce too much pressure, and it is best not to use the toilet, and when using the toilet, do not rub the toilet left and right, do not cause too much impact on the toilet, and also pay attention to the frequency of use.

Three days later. Be sure to ensure that the gaps are clean enough, be sure to deal with them in advance, clean them well, and then dry them thoroughly, and then make glass glue.

We know that the gap between the toilet and the ground needs to be treated with glue after installation, and it is generally not flushed within 24 hours after gluing, because it appears when flushed. After the appearance of moisture, it has a certain effect on its effect, so many people find it after using it. Does it affect the toilet bowl flushed after it is glued?

What to pay attention to when installing a toilet? We know that the gap between the toilet and the ground needs to be treated with glue after installation, and it is generally not flushed within 24 days after gluing, because it appears when flushed. After the appearance of moisture, it has a certain effect on its effect, so many people find it after using it.

I forgot, so I don't know if there will be other effects, so I'll tell you if there is an impact on the toilet flushing after gluing? What to pay attention to when installing a toilet?

Does it affect the toilet bowl flushed after it is glued?

It has an impact on the toilet bowl flushed after it is glued. If you are using neutral glass glue, you need to wait 24 before flushing, and if you are using acid glass glue, you need to wait 48 before flushing. Therefore, it depends on what type of glass glue is used, and after gluing, the window needs to be opened in time for ventilation, so that the glue can be dried faster, and the smell of glass glue is more pungent, and the smell needs to be dispersed as soon as possible.

What to pay attention to when installing a toilet?

1. Installation will begin after receiving the on-site acceptance

Toilets should go through strict quality inspection before leaving the factory, such as water testing, visual inspection of appearance, etc., the best products in the market are generally qualified, but remember, no matter how big the brand, but also in front of the merchant to open the box and inspect the goods, check whether there are obvious defects and bruises, and whether there is color difference in each part.

2. Check and adjust the ground level

After buying a toilet with the same wall spacing size and sealing cushion, you can start the installation. Before the installation of the toilet, a comprehensive inspection of the sewage pipe should be carried out to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation is level, if the ground is found to be uneven, the ground should be leveled when installing the toilet. Cut the drain short, and if possible, keep the drain 2mm 5mm above the ground as much as possible.

3. Check whether there is leakage after debugging and installing the water tank accessories

Check the water pipe first, drain the water 3 5 to flush the pipe, to ensure the cleanliness of the water pipe; Then install the angle valve and the connecting hose, then connect the hose with the installed water tank fitting inlet valve and connect the water source, check whether the water inlet and sealing of the inlet valve are normal, whether the installation position of the drain valve is flexible, whether there is any jamming and leakage, and whether there is any leakage and installation of the inlet valve filter device.

The above is the toilet I introduced, does it have any impact if it is flushed after gluing? What to pay attention to when installing a toilet? Generally, after gluing, it is not recommended to use within 24, after all, this will affect the effect of bonding, of course, the installation of the toilet is a very important job, only in this way can we avoid the trouble in the later stage, and will not affect the use effect because of mistakes between them.

It is best to flush the toilet bowl after 24 hours after gluing, as follows:

It is best not to flush the new toilet just after the installation is completed, although there is a waterproof rubber ring at the base, but the side will generally hit the glass glue, and it is best to flush it after the glass glue is dry. It is recommended that the newly installed toilet be ventilated for 24 hours before using it.

If you use glass glue to glue the bottom of the toilet, you need to wait for more than 24 hours to fully solidify after gluing, if you use cement mortar to glue the bottom of the toilet, you need to wait at least seven days to reach sufficient strength, if you use it halfway, the bottom of the toilet bowl will not be fixed, if you install a rubber flange to seal, it is recommended to wait for 24 hours before use.

Notes:

1. In the process of installing the toilet, do not pour cement mortar into the cavity of the toilet to avoid the cement mortar from breaking the toilet after solidification.

2. The height of the toilet water seal should be adjusted according to the actual situation of the bathroom, if the water seal height of the toilet is too low, it may lead to the phenomenon of aftertaste in the bathroom, but if the water seal height of the toilet is too high, the water in the toilet is easy to splash out, so the toilet water seal needs to be adjusted to the most suitable height.

3. If you plan to drain the toilet again, or move the position of the toilet, you must first raise the ground to make the horizontal pipe slope, which will make it easier to flush away the filth in the toilet, but it is recommended that you do not easily move the position of the toilet to avoid the phenomenon of toilet blockage.

Generally after 24 hours, etcGlass glueRinse only after air drying and curing。Don't be too anxious, because the glass glue just hit still has humidity, is soft, and it takes 24 hours to dry and harden in order to have a sealing effect, so that the toilet flush will not leak and emit peculiar smells, and basically keep the air around the toilet base.

Among them, the types of glass glue are divided into acidic and neutral, acid glass glue cures relatively quickly, and can be cured within 24 hours, while neutral glass glue takes 48 hours, that is, about two days to cure. Generally speaking, the glass glue that is used around the toilet bowl for edge banding and waterproof treatment is acid glass glue, so it can generally be flushed after 24 hours of gluing.

If you accidentally flush within 24 hours, immediately check whether the toilet base is leaking, if so, it may be necessary to re-glue to ensure the tightness of the toilet base.

Glass glue classification:

Glass glue is divided into two types according to its performance: neutral glass glue and acid glass glue. It is generally used for home improvement bonding. The places where glass glue is generally used in home decoration are: the dumb place on the back of the wood line, sanitary ware, and toilets.

Make-up mirrors in the bathroom, sinks and gaps between walls, etc.

The glass glue used in different places is different, because the adhesion of this glue is also different, so when choosing, you should choose according to your own needs.

The surrounding area of the toilet is glued, and it can be flushed at any time, and it has nothing to do with gluing, as long as you don't do it or shake the toilet.

At that time, you can, you can urinate, but you can't be a person, if it's a neutral glass glue, it's basically dry in about six hours

As long as it is well installed, it can be used at any time. Generally, you can sit 24 hours a day.

After 20 minutes, it is ready to flush;

Toilet glue is mostly made of neutral glass glue.

Due to the slow drying time of glass glue, it is usually necessary to wait 24 hours before flushing; If you are using acid glass glue, you need to flush it for 48 hours, because the smell of acid glass glue is more pungent, you need to open the window in time after gluing to keep the air circulating.

After gluing the glass under the toilet, it can usually come into contact with water after 24 hours.

Features: The water tank is embedded inside the wall and can be "hung" on the wall for use.

Advantages: space-saving, drainage on the same floor, very easy to clean.

Lack: The quality requirements for the in-wall water tank and toilet seat are extremely high, and the two products are purchased separately, which is more expensive.

Suitable for families: It is especially suitable for families who have moved the toilet to use, without raising the floor and affecting the flushing speed. Some families who like simplicity and pay attention to the quality of life also often choose it.