Hello, how to do the tiles on the cement slab used for decoration

In fact, the cement brands are different everywhere, it is recommended to use the well-known cement with a good reputation, the general home decoration sand with sand (yellow sand), it is best not to use green sand, because it is more waste of cement and the construction is inconvenient, the proportion of mixing: cement: sand = 1:

2 or; Construction Points:

The base treatment should be clean, the uneven places should be chiseled and repaired first, the base should be clean, there should be no mortar, especially white ash mortar ash, oil stains, etc., and moisten the ground with water. When paving stone and porcelain tiles, standard blocks must be placed, and standard blocks should be placed at the intersection of crosshairs and installed diagonally. During the paving operation, each line should be hung in turn, and the stone must be soaked in water and moistened, and the back should be wiped clean after drying.

The maintenance of stone and porcelain brick floor paving is very important, and it must be sprinkled with water after 24 hours of installation, and covered with sawdust after the towel is paved; Precautions: (1) Before paving, the plate will be tried to spell, and the flowers, colors, and numbers will be consistent with the color of the ground in and out.

2) The stone must be soaked in water and dried. In order to avoid affecting its coagulation and hardening, hollowing, shelling and other problems.

3) After the paving is completed, no one is allowed to go up for 2 3 days. Ceramic glazed bricks are generally selected for household bricks, in other words, it mainly focuses on the geometric size, wear resistance coefficient, and anti-pollution and anti-seepage ability of the bricks. So the brand is not important, the key to see the quality of the bricks, generally I recommend that you go to your local regular large special material market area to buy, do not try to buy cheap to some informal small shops.

Hello, first fix the cement board with cement, and then mix with cement and fine sand according to cement fine sand, water and cement fine sand mixing ratio: 1. Then smear on the cement board, apply the tile evenly, and gently pat the tile with a rubber hammer to make it fit!

Remember not to put the stirred sand ash on the tile first, so that although it is fast, the quality is not as good as the former***! If you are satisfied, thank you!

Hello dear and happy to answer your questions <>

<> how to paste tiles on the cement board is as follows: if the area of tiles that need to be pasted on the cement board is relatively small, you can use tile adhesive to paste directly, which can ensure that the tiles are firmly glued to the cement board. If the tile area is relatively large, the stains on the cement board must be cleaned first, and then the net and grout should be hung and brushed, and then the tile can be pasted.

What should be paid attention to when pasting tiles1, before tiling, it is necessary to check whether the cement used exceeds the use time, if so, resolutely do not use, so as not to affect the overall construction. At this time, the cement needs to be replaced, or the cement needs to be inspected, and it can be used only after it is qualified. The detection method can add an appropriate amount of water to the cement, stir evenly, and wait for 6 hours to see if it can be agglomerate.

2. Before the construction of ceramic tiles, it is necessary to carry out brushing treatment on the construction surface, and only after the treatment can the porcelain ridge bricks be pasted, so as to ensure that the adhesion is stronger and not easy to fall off. If there are tiles on the original wall, then the original tiles need to be removed and the wall surface is treated, and then the tiles can be re-paved, so as to ensure that the tiles are stronger and not easy to fall off. 3. If it is a vertical board, it is necessary to choose a cement board and a light steel keel.

If you put tiles on the cement board, you need to hang the barbed wire first, otherwise it is very easy to fall in the later stage. Then there is the construction of ceramic tiles, which needs to be responsible for professionals, in order to avoid the existence of various detail problems, and avoid the phenomenon of Ming Ye Xian falling off and hollowing out of the tiles, so as to ensure the normal use in the later stage. I hope mine can help you and have a great life!

A few days ago, I went to the community and found that my neighbor's house was being renovated, and I wanted to go in and have a look, and found that my neighbor's house was all tiled. I thought that my neighbor had really spent a lot of money to renovate the house, but after talking to the neighbor, I realized that it was a project given by the decoration company.

This is the site of the balcony tiling. This is really a big project, I see that the master's craftsmanship is good, and he is very serious. This is the method of dry-laying tiles, which makes it more solid.

Level the ground before tiling. The next step is to apply cement mortar, which can be better bonded.

Cement mortar not only has the effect of bonding, but also makes the tile stronger.

When pasting tiles, you must leave gaps, and you must do beautiful seams in the future.

Once the tiles are attached, hit them with a hammer.

After pasting, don't forget to knock each one through.

Look at the tiles on the wall.

It's the restaurant and the whole house is tiled all over.

This is the effect of the bathroom. This is the bathroom wall tile, look at the master's craftsmanship, really good.

A partition is also designed here, which is very convenient and practical to use in the future.

No way. Easy to drop.

The red brick wall cannot be directly tiled, the main reasons are:

1. Direct tiling on the red brick wall will lead to poor tiling or hollowing.

2. Paste the tiles directly on the red brick wall, there may be no problem in the first year or two, but after a long time, there will be a phenomenon of sparse and sparse tiles falling off.

Construction techniques for wall tile pasting.

1. When the base layer is treated, all kinds of dirt on the wall should be cleaned up, and watered and moistened one day in advance. If the base layer is a new wall, when the cement mortar is dry, it should be arranged with bricks, elastic lines, and pasted surface bricks.

2. Before the formal paste, the standard point must be pasted to control the flatness of the pasting surface, and the flatness should be checked with a ruler at any time during operation.

3. Before pasting the tiles, they must be soaked in clean water for more than two hours, and the bricks should be taken out to dry for later use. When pasting, paste from bottom to top, require the mortar to be full, when the ash is lost, it must be removed and re-glued, and it is not allowed to plug the ash from the brick joints and mouths.

4. When laying and sticking, when encountering pipelines, lamp switches, and supporting parts of toilet equipment, etc., they must be cut and matched with a whole brick sleeve, and it is forbidden to use non-whole bricks to patchwork and paste. The whole or independent parts should be pasted at one time, and when it cannot be completed at one time, the stubble should be left at the construction joint or the dark corner.

Spray the wall first until it is wet, then wipe one side with clean plaster, and then scrape the sand and mortar (preferably glue) on the back of the tile to paste the tile.

The correct construction steps are, the concrete slab wall is first smeared with a layer of plain cement slurry (pure cement slurry) solid layer, and then smeared with a layer of one centimeter thick mortar, rubbed the hemp surface, within ten hours to paste the tile, with the wiping and pasting, the plastering layer can not be overnight, in this way, the firmness can reach the maximum, really help you look forward to adopting,

Process flow:

Light partition wall pay-off Install the door opening frame Install the keel along the top and along the ground keel Vertical keel binning Install the vertical keel Install the transverse keel card file Install the gypsum cover panel Construction joint practice The surface layer construction first uses a grid (fixed with 30 vertical nails, so that a thin layer of cement bottom surface is smeared on it (choose a thinner because, when the overall wall is pasted with tiles, the thickness is about 4cm, if your bottom layer is too thick; Cracks appear over time. This is caused by the pulling of the entire wall on top of the wall. So be thinner) and when it's almost dry, you can stick it.

Specifically: 1. Pay-off: On the ground, wall and top surface according to the design position, play the horizontal double-sided edge line and hole line of the tube well partition wall, pop up the vertical line of the façade, pop up the top connection line, and divide the bin according to the width of the plate.

2. The longitudinal length of the pipeline well skeleton mesh is made of 50*50* galvanized square steel as the main keel, the secondary skeleton mesh is made of 20*40* galvanized square steel as the keel, and the transverse through keel is made of 40*60* galvanized square steel to meet the installation of cement board veneer. In order to facilitate the molding of cement veneer, the spacing of the main and secondary keel molding mesh is arranged at intervals according to the actual situation of the site. In order to ensure the vertical stability of the skeleton, all welds must be spot-welded and connected, and the welds should be brushed with anti-rust paint twice.

The skeleton must be modeled to ensure that the dimensions meet the design requirements.

3. When the cement board is installed, it is necessary to use special tools to cut and loft the test installation, and the large façade is pressed into the small façade for reinforcement. The installation adopts 3*30mm galvanized self-tapping screws, which are fixed on the galvanized square steel keel. Pasting tiles on partitions is generally universal

First, the place where the tiles need to be pasted are fixed with a grid (fixed with 30 vertical nails, and then a thin layer of cement bottom surface is smeared on it) (choose a thinner one because, when the overall wall is pasted with tiles, the thickness is about 4cm, if your bottom layer is too thick; Cracks appear over time. This is caused by the pulling of the entire wall on top of the wall. So be thinner) and when it's almost dry, you can stick it.

Summary. If the area of tiles that need to be paved on the cement board is not large, you can directly apply the tile adhesive and paste it on it. If the area that needs to be paved is very large, it is necessary to hang the net brush paste and then pave, so as to ensure that the tiles will not crack and fall off during construction, and the dust stains should be cleaned up during construction, so as to avoid hollowing and cracks in the later stage.

How to put tiles on cement slabs?

Hello, I have seen your question and am sorting out the answer, please wait for a while If the area of tiles that need to be paved on the cement board is not large, you can directly apply the tile adhesive and paste it on it. If the area that needs to be paved is very large, it is necessary to hang the net brush paste and then pave, so as to ensure that the tiles will not crack and fall off during construction, and the dust stains should be cleaned up during construction, so as to avoid hollowing and cracks in the later stage.

Can you use stupid board glue to directly paste tiles?

Benzene board glue can not be used to stick ceramic tiles, benzene board glue is suitable for foam products with different densities and different shapes.

When we decorate the interior, we will use a variety of materials, among which the cement board is a kind of building slab that is processed and produced with cement as the main raw material, which is a widely used material in the construction industry.

Tiles can be applied to cement slabs. If the area of the tile on the cement board is small, you can directly use tile adhesive to stick the tile on the cement board, if it is a large area of tiles, you need to hang the net to brush the grout and then paste the brick, so that the tile can be guaranteed will not crack and fall off. At the same time, when we paste tiles on the cement board, we also need to thoroughly clean the dust and debris, so as to avoid defects such as hollowing and cracking of the tiles.

What are the types of cement slabs.

1. Ordinary cement board.

Ordinary cement board is a relatively low-grade product, but it is very commonly used. The plate specification is usually 1200 * 2400 *, the thickness is usually between 6 and 12cm, the market ** in the range of 10 to 20 yuan, mainly cement, fly ash, sand, ** low cement dosage is also lower.

2. Fiber cement board.

The biggest difference between the fiber cement board and the ordinary cement board is that each fiber is added as a reinforcing material in the making process, so that the strength, flexibility and impact resistance of the cement board are greatly improved, and the added fiber materials mainly include asbestos, pulp, vinylon, glass filament, etc.

3. Fiber cement pressure plate.

The main difference between the fiber cement pressure plate and other cement boards is that it is pressed by a special press in the production process, so the plate has the characteristics of high density, waterproof, fireproof, sound insulation, etc., and the bearing and bending and impact resistance of the plate are also very good, and the performance of the plate is not only affected by the raw materials, formula and process, but also affected by the size of the press pressure.