Why does it take not long for the kitchen and bathroom to be covered with polished tiles?

Kitchen and bathroom sticking polished tiles, the reason why it will fall off: for the kitchen and bathroom wall paving polished tiles in the dining room, it is equivalent to the construction technology of the wall on the floor tile, because the polished tile was originally designed to be paved on the ground, and the water absorption rate of the equipment itself is low, so when it is used in the paving of the wall, it is necessary to apply the special construction technology of the floor tile on the wall, as long as this can ensure that the grinding and polishing floor tile parquet is not likely to fall off and loosen on the wall of the kitchen and bathroom.

For polished tiles, in the production usually out of consideration of the surface of the floor tile, will carry out polishing and waxing solutions, can be for some small brands of ceramic tile processing plants, in the development of this polishing and waxing engineering construction of the surface of the polished tile, often because of the delicate engineering construction, the back of the polished tile is also done on a layer of wax, so that the polished tile is not polished off when the paving is carried out, no matter what the operation method to carry out the paving, there will be quality problems, Because this layer of wax will cause the polished tile to be laminated with the adhesive.

For the wall tile paste in the kitchen and bathroom, the mixed mortar is generally used as the paste, because when the general superabsorbent floor tiles are applied, the mixed mortar can be very good to paste the tiles firmly, and the quality and quantity are guaranteed. For the polished tile to the wall, due to the low moisture content, if the mixed mortar is still used to polish the polished floor tile parquet, it will cause the problem of falling off and loosening soon after the polished tile and the mixed mortar are paved, because the polished tile itself cannot effectively integrate with the mixed mortar when the water absorption is low, so there will be product quality problems.

Dismantle all the wall tiles of the kitchen and bathroom, dismantle the floor tiles of the bathroom, and remove all the original pasted mixed mortar to be clean and tidy, and expose the initial wall; Seal the waste after dismantling at the construction site to ensure that the site is hygienic and tidy; The original walls of the kitchen and bathroom are constructed with mixed mortar to ensure that the mixed mortar of the wall is qualified, and the vertical angle is qualified, and the corners of the walls in each individual area are all 90 degrees.

This phenomenon may be due to the ceramic tile itself, the construction of the wall is not reserved for treatment, and it is also possible that the tile adhesive is not used, there will be a phenomenon of falling off.

Because no qualified construction technology is used, the wax on the surface is not treated during polishing, which leads to delamination between this layer of wax and adhesion, so it will fall off.

It may be because the tiles are not soaked in water when the tiles are pasted, or it may be because the quality of the cement is not good or the quality of the sand is not good, or the quality of the adhesive is not very good, or it may be that the construction person's skills are not very good, so it will fall off.

First: I've seen that dry walls also fall tiles. Usually there are large cavities underneath. It is likely that the air expansion and contraction blew the wall tiles apart. Therefore, when the mason brushes are not even, not leveled, and not pressed well.

Second: If the cement is not good, because it should be a large area of drop, there are few good pieces left. That is, cement is not good.

Third: ceramic tiles also have a service life, in fact, there is still fungal activity in the cement, and it is normal for about 30 years to fall, after all, it is not a century-old project. If it is a century-old project, the back of the tile should have a deep pattern and groove to help catch the wall.

The quality of the tiles also needs to be ***.

In short: most of the tiles I see are hollow in the back. Maybe it's because the buildings I've seen are all relatively early, so I don't know enough about the old buildings with tiles.

Improvement plan: First: when pasting, it should be smooth.

Second: to obliquely post exhaust and tremble, and use a rubber hammer to knock more; Third: buy a deep groove of the remaining tiles.

Fourth: the quality of cement should be checked, and there is indeed rotten cement. Fifth:

The blending of cement, and so on to operate in place, not enough moisture, still drop.

Polished tile belongs to a kind of whole tile, its water absorption, its commonly used bonding materials are mainly cement mortar and tile adhesive, the reason for its falling off, according to the different bonding materials, mainly in the following aspects:

1. The reasons for falling off caused by the use of cement mortar paving:

1) The improper ratio of cement and sand leads to the reduction of the bonding strength of the cement mortar, which causes the whole tile to loosen and fall off;

2) The mud content of the sand used in the configuration of cement mortar is too high, which leads to the reduction of its bonding effect;

3) The wall base is too flat and smooth, and the brushing treatment is not done, and the effect of brushing is mainly to increase the bonding area of the cement mortar of the bonded tile and the base layer, so as to increase the firmness of the tile paste;

4) The wall base layer appears hollow drumming delamination, such as the cement mortar plastering layer of the base layer, the waterproof layer and the base layer delamination, etc.;

5) When the tile is paved, the wall base is not sprinkled and moistened, which causes the dry wall surface to absorb the moisture in the cement mortar smeared on the back of the tile too quickly, so as to artificially shorten the natural solidification cycle of the cement mortar, thereby causing its bonding strength to be reduced, causing the tile to loosen and fall off;

6) There is a release agent on the back of the tile that is not cleaned, and the first crack causes the tile and the cement mortar to delaminate and cause loosening and falling off;

7) The cement mortar coated on the back of the tile is uneven, and it is closed and full, resulting in hollowing and delamination of the tile paving;

8) The tile paving and retention joints are too small, due to the change of temperature and humidity in the indoor environment, causing the thermal expansion and contraction of the tile, thereby causing loosening and falling off;

9) In the case that the tile paving is not dry and solid, the caulking treatment is carried out, and in the process of squeezing the filling caulking material into the brick joint, the tile is artificially loosened, causing the tile to fall off in the later stage.

2. The reasons for the tile falling off caused by the use of tile adhesive paving:

1) The wall base layer appears hollow drumming delamination, such as the cement mortar plastering layer of the base layer, the waterproof layer and the base layer delamination, etc.;

2) There is a release agent on the back of the tile that is not cleaned, which causes the tile and the cement mortar to delaminate and cause loosening and falling off;

3) The selected tile adhesive does not match the material of the ceramic tile used, such as choosing the adhesive to bond ordinary ceramic tiles to paste the whole tile, because the ceramic tile adhesive has low strength requirements, it is not suitable for pasting the whole tile;

4) The selected tile adhesive is mixed with cement sand and other materials, which changes the bonding effectiveness of the adhesive, thereby causing the tile to loosen and fall off.

5) The tile adhesive applied on the back of the tile is not full and uniform, resulting in hollow delamination of the tile paving;

6) In the case that the tile paving is not dry, the caulking treatment is carried out, and in the process of squeezing the filling caulking material into the brick joint, the tile is artificially loosened, causing the tile to fall off in the later stage.

6) The tile paving and retention joints are too small, due to the change of temperature and humidity in the indoor environment, causing the thermal expansion and contraction of the tile, which will cause loosening and falling off;

If only the tile is falling off, and the mortar is left on the wall and the floor is not loose, the solution is to scrape the remaining mortar on the reverse and side sides of the tile, and then apply a uniform layer of mortar on the reverse side of the tile and press it back to the original point.

If the mortar and tiles burst out together, the solution is to first dig some pits on the basic surface of the wall and the ground, then layer a layer of mortar on the basic surface, and then press the tiles up until the tiles are fixed on them.

Tile falling off is generally due to the general cement mortar to be bonded when paving, the adhesion of cement mortar is relatively low and very susceptible to external environmental hazards, and there are often hollow and even falling off the tile wall. If such a problem occurs, it is best to switch to tile adhesive with strong adhesion and moisture resistance. The special type of tile adhesive is not easy to be harmed by the environment, is very easy to use and inexpensive.

Tile paste can repair significant cracks, and can be purchased in the general large and medium-sized home building materials market, and tell the store about the cracks in the house, and he will understand what to let you. The key is to use tile paste after caulking, it can produce a smooth visual impact that is basically the same as the porcelain surface, and is strong and wear-resistant, and is generally used by users with very high interior decoration specifications. There are many colors to choose from in tile plaster, according to the well-known brand and net weight price differences, the general is more than 10 people.

If there are quicklime powder, wall paint, wallpaper and other decorations on the wall, or there is waste on the ground, it must be clean and tidy, otherwise the cement mortar and the bottom layer are not firmly bonded; In addition, if there are cracks in the wall itself, the tiles should be properly disposed of before tiling can be applied to prevent the wall tiles from cracking or falling off due to the increase of the basic structural cracks in the future; Also, for the ground and walls with great differences in flatness or flatness, it is also necessary to use cement mortar to carry out ground leveling. This will reduce the likelihood of tiles falling off.

In people's homes, a good tile can make our bathroom produce a very good decoration effect, to ensure that we have a stronger natural environment in the process of washing. If you encounter the problem of bathroom tiles falling off, you don't have to worry too much, according to the above for you to explain this way of dealing with bathroom tiles falling off the repair method can quickly find the cause of the problem, and then apply reasonable methods to repair the falling off bathroom tiles, to ensure that people's bathroom overall interior decoration natural environment.

Because of the reason that the sticking is not firm, because of the problem of cement, in this case, you can only re-paste the brick, it is best to choose some cement with strong viscosity.

It may be because the tiles were not pasted well at that time, and it may also be because the tile adhesive at that time may not be strong enough. If you want to solve the problem, you should buy another tile and stick it in the corresponding position.

The polished tiles in the kitchen and bathroom are loose and fall off, which may be due to the immaturity of the wall wetting process, or the wrong choice of pasting materials, and it is best to choose two-component vitrified rubber back tiles.

Because the kitchen and bathroom are usually damp and dark, it will cause the viscosity of the cement behind the tile to become weaker, and due to the gravity of the tile itself, the tile will fall off.

This is when pasting, there is a certain problem in the process, the worker master who pasted it for you is not professional enough, your wall is not polished, the ratio of cement and sand is not right, and the tile is not brushed or blistered in advance, this situation will occur.

Tiles are prone to hollowing and falling off. There are many kinds of cement mortar, suitable for home decoration paste tiles is several, if the choice of cement mortar is not and tile material, paste tile can not achieve the ideal effect. Tiles are prone to hollowing and falling off.

There are many kinds of cement mortar, suitable for home decoration paste tiles is several, if the choice of cement mortar is not and tile material, paste tile can not achieve the ideal effect.

When the bathroom wall tiles are paved, the opposite side must be leveled first, because the tiles are paved from the bottom up, and the floor tiles are pressed after the wall tiles are paved.

In order to prevent the tile from falling off in the later stage caused by the heavy tile, it is necessary to pay special attention to the intersection of the wall and the ground. Although it is troublesome to deal with, it can save a lot of thought in the later stage.

Tiles are prone to hollowing and falling off. There are many kinds of cement mortar, suitable for home decoration paste tiles is several, if the choice of cement mortar is not and tile material, paste tile can not achieve the ideal effect. So these friends asked, what is the possible cause of the falling tiles in the bathroom?

How can we prevent this from happening?

smashed into the guests who were bathing, the scene couldn't bear to look at directly, and the blood did not stop. Therefore, such problems must be paid attention to and prevent disasters before they occur. There are several main reasons why tiles fall off.

Many times the wall of the bathroom is hollow, but during the house inspection, many people do not find it, resulting in the later tiles pasted and hollow. Ceramic tiles are divided into full tiles and half tiles, full tile paste is to use tile adhesive + adhesive to paste, half tile is to soak through water to paste, the general wall is soaked in water bricks, but the whole tile also falls off. Paste it again, this time it's more troublesome, I asked him, do you know what caused it, he vaguely thought that it was a long time, the tile was broken, in order to solve Xiao Wei's question.

Therefore, a new type of tile adhesive product was born. However, you must pay attention to the choice of tile adhesive, otherwise the wall tiles are still easy to fall. In such a situation, many friends don't know what to do, so what may be the reason why the tiles in the bathroom fall down?

Today, I will talk about it in detail. Inconvenient to cleanGenerally speaking, wall tiles are smoother and easier to clean than floor tiles; And the floor tiles on the wall increase the cost of cleaning. Especially in the kitchen, if the floor tiles are on the wall, thinking about the problem of oil stains will make you very painful.