What to do if the tiles on the bay window suddenly fall off? Do you have any recommendations for til

The surface floating layer should be cleaned before tiling on the wall of the bay window in the initial bedroom, and then the tap water should be cleaned, and the wall should be painted after drying, and the wall solid can improve the tightness and grasp of the wall, and the structural reinforcement concrete is bonded to the wall. Bedroom bay window tile cut can not be directly applied to the general cement yellow sand composition, at least to use adhesive, it is best to apply balance cement to pave, to ensure the solidity of the tile paving, although the cost has risen, but to ensure safety, relative to the safety of this cost is not a big cost. Bedroom bay window paving tile tiles before paving to ensure that the ordinary brick soaking work to do a good job, summer construction must pay attention to the water soaked out of the time is too long, is to carry out the second soaking, tile paving after the completion of the timely sprinkling maintenance.

As a technical professional tile master, the following work experience is given, for reference only. This is often the case. The cracks in the middle of the tiles were small when paved before, and the heat and cold contraction were harmful, and the tiles fell off, especially the bricks in the window, and the probability of falling off was particularly large.

The wall is not calendered or dispensed, and the cement and sand ash are not firmly bonded to the wall and fall off. After the tile is sharpened at 45 degrees, the dust on the brick is not removed, and the tile falls off. The percentage of concrete and sand in the sand ash is wrong, and if there is too much sand, it will fall off.

Generally, in this case, there are the following overhauls are more commercial insurance 1, with dry hanging glue and structural adhesive, the benefit is convenient, the disadvantage is that you can not hang things 2, with tile adhesive again, more laborious, <>

According to the ** analysis, it is not paved with tile glue or mixed mortar at all, so which five "flatbreads" printed at the bottom end may be glued with dry glue or other adhesive raw materials? Knowing that it is shoddy or too much to firmly believe in the adhesion of viscose, it is already a great luck that the tiles do not fall off without damaging people? Isn't it ideal to use other raw materials to replace the top of the bedroom bay window with a ceramic tile decoration design like this?

Even if the problem has already occurred, we need to think about how to solve it, what should we do? For which tile glue does not fall off the brick is really afraid to ensure? You must know that although the raw materials for tile adhesive are critical, the engineering construction skills and sense of responsibility are so critical!

Everyone has been using JCDecaux tile adhesive all these years, and if you are used to it, you are afraid to apply other brands at will? I am afraid that product quality problems will jeopardize everyone's user evaluation and credibility in the industry!

Remove the appendages on the reverse side of the tile: release agent or release oil. It has the effect of protection, and it does not stick to all raw materials, including Kelin back gluing.

If it is not cleaned and tidy, it is very easy to cause the wall of the tile to fall off; Brush the back of Kelin glue: the reverse side of the tile is facing up, and the self-adhesive is evenly brushed with a roller or soft brush, and the tile is kept at a level to dry (to prevent the fluidity of the liquid and the environment from polluting the front face or road surface of the tile). After brushing, the moisturizing lotion changes from milky white to completely transparent and sticky, and you can put tiles on the wall.

The amount of back coating glue varies slightly depending on the thickness of the brush, and the total area of the brush varies slightly. The length of time it is hung due to the hazards of the construction environment (environmental humidity, ambient temperature, wind force).Generally, it must be dried for 1-2 hours to continue the next step of project construction.

If there are lime plaster, latex paint, wallpaper and other decorations on the wall, or there is dirt on the ground, it must be cleaned up, otherwise the cement mortar is not firmly bonded to the base layer; In addition, if there are cracks in the wall itself, it should be properly treated before tiling, so as to avoid cracking or falling off the wall tiles due to the enlargement of the cracks in the basic structure in the future; In addition, for the ground and wall with too large a difference in flatness or verticality, cement mortar should be used for leveling.

After the bay window is renovated, if the tiles suddenly fall, they need to be repaired. The choice is better, and the tile adhesive is not easy to drop. You can go to the decoration materials, and the company chooses a little better.

It is necessary to pay attention to safety issues, it is necessary to inspect other tiles and then repair them again, it is better to choose cement, cement is the strongest.

First of all, this should be based on the severity of your wall tiles falling off, if the area of falling off is relatively small, then you can partially repair and re-paste those pieces, the specific method is as follows: x0d x0a1Clean up the old cement where the tiles have fallen off.

Take out the tiles and dry the water on the surface, then evenly apply the prepared cement mortar to the tiles (the thickness is about the same as the original cement slurry), and then knot it in the place where it falls off. \x0d\x0a4.Knock it flat with a wooden hammer and you're good to go.

The so-called ceramic tile is a kind of acid and alkali resistant porcelain or stone building or decorative material formed by grinding, mixing, pressing, glazing and sintering of refractory metal oxides and semi-metal oxides, which is generally called ceramic tile. Its raw materials are mostly made of clay, quartz sand, etc. In the decoration of Shenyang, the application field of wall and floor tiles is becoming more and more extensive.

However, due to various reasons, after the use of wall and floor tiles for a period of time, local tile hollowing and even falling off often occurs, which not only affects the use of the effect, but also affects the appearance. 1. If the mortar is not loosened, only the tile falls off: the mortar adhered to the back of the tile and the surrounding area can be scraped clean, mixed with a little cement in 107 glue to form a paste, evenly coated with a thin layer on the back of the tile, and then press the tile.

2. If the mortar falls together with the tiles: first gently chisel some pits on the original foundation surface, and re-inlay them with mortar mixed with 107 glue, or use cement, E-44 epoxy resin, acetone, ethylenediamine according to 5:3:

After mixing well in a ratio of 2:1, brush a layer on the foundation surface with a brush, and then press the peeling tiles on until the mortar hardens.

First of all, this should be based on the severity of your wall tiles falling off, if the area of falling off is relatively small, then you can partially repair and re-paste those pieces, the specific method is as follows:

1.Clean up the old cement where the tiles have fallen off.

2.Soak the tiles in water for a period of time, and the specific soaking time is subject to the fact that the tiles do not bubble in the water.

3.Take out the tiles and dry the water on the surface, then evenly apply the prepared cement mortar to the tiles (the thickness is about the same as the original cement slurry), and then knot it in the place where it falls off.

4.Knock it flat with a wooden hammer and you're good to go.

This repair method is aimed at the situation that the area of bricks dropped is relatively small, and the cement river sand was used to paste the bricks. However, if the falling off situation is more serious, it is still recommended to remove all the bricks and then re-til.

In fact, now the ceramic tile is getting better and better, so the water absorption rate is constantly decreasing, the traditional cement river sand can no longer meet the requirements of the tile, and the size of the tile is getting larger and larger, so it is more difficult to stick, so it is recommended to use professional knot materials, such as porcelain stickers to paste tiles, so that not only the adhesion force is strong, it is not easy to fall off the hollow drum, and the thickness of the knot is thin, environmentally friendly and non-toxic, and the aesthetics and firmness of the tiles have a good guarantee.

There are many reasons why wall tiles can fall off, and it can be due to the long renovation of the house. It could be a problem with construction: 1

Grassroots treatment problems: the wall and ground base treatment is not clean, the watering moisture is not enough, the floating dust on the back of the tile is not removed, and there are too many water traces before paving, which will lead to the tile and the wall are not tightly bonded, and there will be loosening and falling after a period of use. 2.

Tile quality problem: The quality of the tile is also one of the reasons for loosening, and the water absorption rate of the tile directly affects the firmness of the paste. The state stipulates that the water absorption rate of porcelain tiles is E, and the shrinkage and expansion rate of porcelain tiles is about 4 10-6, when the water absorption rate of ceramic tiles or cement does not reach the standard, after the occurrence of thermal expansion and cold contraction, the shrinkage rate of ceramic tiles and cement is inconsistent and leads to separation and falling.

3.Construction process problems: during the construction process, if the cement mortar of the cushion is too thick or the cement is added too much water, the tiles will fall; In addition, if it is a large-size tile, if the seam is too small, the thermal expansion and cold contraction will squeeze each other, which is easy to cause warping and cracking.

4.Problems in daily use: the water absorption rate of the inner tile is low, if the tile is not fully fitted with the cement, it is subjected to a large impact force, such as trampling or the impact of hard objects, it is easy to cause the separation of the tile and the cement, and the bottom of the brick is hollow.

Generally, the tile falls off and can be repaired in the following ways: 1Corner hollow drums:

If it is found that there is a hollow drum on the edge of the tile after paving, the part of the partially hollow drum can be watered to avoid overall replacement. 2.Local hollowing:

If there is a small amount of partial hollowing of the tiles on the wall and floor, if it does not affect the installation of cabinets, mirror cabinets, showers and water heaters, etc., it can not be treated, but if it affects the installation and daily life, it is recommended to knock off the local tiles and re-pavement. 3.Large area hollowing:

If there are 2 3 tiles in the space, it is recommended to remove them all and re-pave.

Traceless reinforcement on the original tile, no need to repaste, economical, economical and beautiful!

1. Clean up the cement at the place where the tile falls off first, exposing the cement base.

2. Pour the porcelain paste powder into special water and stir it into a paste (the mixing ratio is: 20kg powder and 6kg water), and after stirring, it needs to be left static for about 10 minutes, and then stirred slightly before it can be used, which helps to increase the adhesion force.

3. Use porcelain tile adhesive to repair and level the peeling cement base surface, and then evenly apply the tile adhesive to the back of the tile.

4. Knead the tiles to the place where they originally fell off.

5. Finally, gently tap the tile with a rubber hammer to make it consistent with the height of other tiles.

1.If it has fallen off, buy a piece that is basically the same and come back, paste it with tile glue, and temporarily fix it with transparency.

2.Comprehensively check whether other tiles have hollow drums, for the sake of safety, all tiles can be reinforced in two ways: Reinforcement with open nails (the so-called open nails are the screws that can be seen after reinforcement) Adopt non-trace reinforcement (after reinforcement, the color is toned to fill back the screw holes, and the screws can not be seen, so that it looks beautiful).

Using MS glue to paste tiles has a much better effect than traditional cement yellow sand tiles. The material cost of cement and yellow sand is eliminated, and the labor cost is also reduced a lot, and the construction efficiency is improved, so I can move in early. Greenridge MS modified silane glue, all properties are excellent, sealing and waterproof, high and low temperature construction, the highest adhesion force reaches 30kg square centimeters.

Abstract] Through the analysis of the causes of wall tile sticking and falling off, appropriate maintenance plans are adopted to solve the problem of tile falling off and throwing bricks to avoid similar problems in subsequent construction.

1.Overview of the project.

Tiantai Qingchengyuan project is located in the area at the junction of Jiangjun Avenue and Focheng West Road, Jiangning Development Zone, Nanjing. The total construction area is invested and built by Jiangsu Tiantai Construction and designed by Nanjing Zhongyi Architectural Design. The commencement date is August 25, 2008 and the completion date is September 26, 2012.

According to the requirements of the construction unit, the wall finish is changed to a 12mm thick tile, the size of the tile finish is constructed according to the requirements of the construction unit, and the actual construction, the specific decoration scheme is declared by the construction team, and the construction is approved by the supervision and construction unit.

At the beginning of 2011, some wall tiles in Building 1 fell off, especially in the lobby, and the first tile of the front room of the floor was disturbed, while the tile of Building 2 was not found to fall off. According to the requirements of the property and Party A, the falling tiles are repaired and pasted with construction glue cement mortar. By the beginning of 2012, there were more wall tiles falling off in the winter stage, and from the perspective of tile falling off, the adhesive layer and the finishing layer on the back of the tile were peeling off.

There are radial cracks on the surface of some bonded mortars, and the cracks are mainly located in the center of the plate bonded mortar.

2.Cause analysis.

The construction stage of wall tiles is July to August, when the temperature is high, and winter.

If the mortar is not loose but the tiles are falling off, it means that it is not the mortar problem. You can clean the back of the tile first, and then use special mu ridge glue mixed with less volt cement to apply it on the back of the tile and re-paste it; If the mortar and ceramic tiles are loose and cracked together, chiseled on the surface of the sticky mortar, and then mixed with special glue, the cement mortar is heavy and resistant to damage.

First look at how large the shedding area is, the shedding area is large, and all the walls can only be cleaned and re-tiled. Generally, the wall is easy to crack and fall off after a long time or the wall has high humidity.

Small surface treatment method: remove the residual concrete on the position of the tile wall that has fallen off, and find cement and mortar again (you need to prepare it yourself, master the preparation ratio of cement: mortar is approximately 1:

1. Appropriate amount of water, slightly dry, too thin, only suitable for small area subsidies). It is necessary to paste the tile wall and pour water three times repeatedly to make the wall absorb some water, and soak the water basin with tiles for about half an hour to make it absorb water. The concrete is applied to the back of the tile and the paste begins.

There is also a way to apply egg white to the back of the tile, or to apply construction glue (available in the building materials market).

Ceramic tiles, also known as tiles, are refractory metal oxides and semi-metal oxides, through the process of grinding, mixing, pressing, glazing, and sintering, and form an acid-alkali resistant porcelain or stone, etc., building or decorative materials, called ceramic tiles. Its raw materials are mostly mixed with clay, quartz sand and so on.

The surface of the body brick is not glazed, and the material and color of the front and back are the same, so it is named the whole body brick. Full-body brick is a kind of wear-resistant brick, although there are varieties such as seepage bricks, but relatively speaking, the color of full-body bricks is not as good as glazed bricks. As the interior design is more and more inclined to plain design, so the whole brick has become more and more fashionable, the whole body brick is widely used in the hall, aisle and outdoor walkway and other decoration projects on the ground, generally less will be used for the wall, and most of the non-slip bricks belong to the whole brick.