Hello, I want to ask how much is the broken switch of the shower?

It is not recommended to repair the broken shower switch, and I will replace it when this happens at home. Of course, broken dads sometimes doForciblyTaking it apart, although the structure inside is not complicated, it is quite difficult to repair.

For example, generally shower switches are two-phase water inlet, with cold water on one side and hot water on the other. There will be rubber gaskets behind these two holes, if the gasket is broken, it can naturally be replaced and repaired, but the problem is not that the switch is leaking, but that it is broken. That is to say, either the water does not come out when it is wrenched, or the water temperature cannot be adjusted by twisting left and right

How can this situation be repaired?

Duplex waterway switch.

There is indeed a screw behind the switch and on the handle (with the hot and cold water signs removed) that can be unscrewed to see what is wrong inside, but it is very difficult to repair it, not only do you need special tools, but only two inlet and outlet channels or valve spools can be seen inside after unscrewing. In other words, even if you forcibly dismantle the valve core, it will be difficult to figure out if it is broken, and replacing one may not be useful.

In short, it is difficult to repair a broken shower switch, and even if it can be repaired, it is not only time-consuming and laborious, but even the cost of this is not as good as buying a new one. Of course, if it is a branded shower switch, some can be replaced directly and free of charge. However, it also depends on the merchant's regulations, such as:Some have a three-year warranty, some have a five-year warranty, and the longest I've seen is 10 years, I won't talk about the brand here, you can check it yourself.

There are many kinds of showers, cheap dozens of dollars if o cheap dozens of dollars, if a little more expensive, even thousands of dollars, its switch is also different, cheap may be dozens of dollars, if a little more expensive, may reach hundreds of dollars.

Summary. Hello! 1. When the shower switch is damaged and needs to be repaired, you should first turn off the main valve of the tap water at home, then pry off the decorative cap of the shower switch handle, and then use a tool to unscrew the screws, and then you can remove the handle.

When disassembling the handle, it can be removed as long as it is rotated twice, and in the process of disassembly, the screws must be kept to avoid loss.

2. Secondly, you need to disassemble the decorative cover, and you need to use a little force when dismantling. Then use a tool to remove the gland nut as well. After the gland nut is removed, the exposed part is the valve core, which is an important part of the shower switch.

3. Next, the damaged valve core should be disassembled, and then the installation position of the valve core should be flushed with clean water, so that the internal impurities can be flushed clean. After cleaning and ensuring that there are no impurities on the surface, install a new valve core of the same specification and model, and be sure to align the hole position when installing.

4. After the position of the valve core is fixed, you can install the gland nut back, and when installing, you should rotate the valve core according to the clockwise direction until it cannot be rotated. Finally, the handle should be installed at the outlet of the hot water pipe, and the screws should be screwed back on, and the decorative cap should also be pressed up.

How to fix the shower switch switch is broken.

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

Hello! 1. When the shower switch is damaged and needs to be repaired, you should first turn off the main valve of the tap water at home, then pry off the decorative cap of the shower switch handle, and then use a tool to unscrew the screws, and then you can remove the handle. When disassembling the handle, it can be removed as long as it is rotated twice, and in the process of disassembly, the screws must be kept to avoid loss.

2. Secondly, you need to disassemble the decorative cover, and you need to use a little force when dismantling. Then use a tool to remove the gland nut as well. After the gland nut is removed, the exposed part is the valve core, which is an important part of the shower switch.

3. Next, the damaged valve core should be disassembled, and then the installation position of the valve core should be flushed with clean water, so that the internal impurities can be flushed clean. After cleaning and ensuring that there are no impurities on the surface, install a new valve core of the same specification and model, and be sure to align the hole position when installing. 4. After the position of the valve core is fixed, you can install the gland nut back, and when installing, you should rotate the valve core according to the clockwise direction until it cannot be rotated.

Finally, the handle should be installed at the outlet of the hot water pipe, and the screws should be screwed back on, and the decorative cap should also be pressed up.

How can I buy the spool seal that needs to be replaced.

There is a shop that sells water heaters.

I bought the Wrigley shower at the online Xiaomi counter, but the physical store doesn't have it, what should I do?

Hello! Most of the spool seals are the same and can be used, or they can be bought in physical stores.

A broken shower switch can be caused by:

1.Damaged movement: When the shower switch movement is damaged, the shower will not be able to open or close properly. At this point, the shower needs to be removed, the condition of the movement checked and the damaged movement replaced.

2.Aging of the sealing ring: When the sealing ring of the shower switch is aging or damaged, it will also lead to poor water flow or water seepage. In this case, the seal needs to be removed and replaced with a seal of the same specification.

3.Blocked faucet: When the faucet of the shower switch is blocked, the water flow will be poor or not at all. In this case, you can use a fine needle or toothpick to clean the dirt inside the water nozzle, or use a detergent to clean it up.

4.Loose wire connection: If the shower switch is an electric switch, then a loose wire connection will also cause the switch to fail. At this point, you need to check whether the wire connection is loose and re-fasten.

It should be noted that when repairing the shower switch, the water inlet valve should be closed first and the water should be completely drained to avoid the danger of water flow to the operation. If you are not sure how to make the repair, it is advisable to seek the help of a professional.

Summary. Hello dear; I'm glad to answer for you How much does it cost to replace a leaking shower switch? : The general shower** is between 200 and 400, how much does it cost to replace the shower switch leakage?

Hello dear; I'm glad to be able to answer for you How much does it cost to replace the water leakage of the shower? : The general price of showers is between 200 and 400, that is, the converter under the shower has been leaking. If so, how much does it cost?

It's the place where I drew the red circle, and it keeps leaking.

It's that the converter under the shower keeps leaking. If so, how much does it cost? Generally 200 yuan at a time, hello, is it still there?

Hello, is it still there?

Okay, I'll collect the cost here.

The place you circle out 1, you can use the special glue hunger boy pure cloth to wrap tightly, this is the most cost-effective --- cost of adhesive tape 2, it is expensive to change, accessories about 350 + labor cost 70 base 3, call the maintenance Qi Wu master to come to the door to rotten instructions about 200 can be done.

Here's how to replace it:

1. What should I do if the shower switch faucet is leaking?

We first tethered the faucet tightly, and then used a wrench plier to turn the faucet back off in a counterclockwise fashion. Turn the threaded hole outward, and roll 5-6 coupons clockwise with raw meal tape on the threaded part. Check whether the faucet is adjusted correctly, bolt it in clockwise with a wrench, and then open the sluice gate to test whether it will still leak.

2. The cause of water leakage at the water outlet.

It is caused by long-term wear and tear of the axial gasket in the tube. We can remove the gland, remove the old gasket with a clip and replace it with a new one. Water leaks in the gap under the faucet bolt.

This is mainly due to the wear of the triangular gasket on the inside of the gland, and it is also very simple to deal with, just make the gear resistant to sell and prefer the new gasket. Water leakage at the switch connection. Mainly because the cap nut is loose, only need to re-tighten the nut or U-shaped gasket.

How to remove the shower switch

1. Before disassembling the shower switch, we must first close the water main gate, then pry off the decorative cap of the handle, and then loosen the screws to start to easily remove the handprint. Generally speaking, it can be removed after two turns. During the dismantling process, the screws should be placed well to avoid loss.

2. We need to twist off the decorative cover, this step requires a little force to brighten the air, and then we can remove the gland nut homeopathically. The part that is exposed when removed is the spool, which is the key part of the shower switch. Once removed, it can be rinsed internally to remove impurities.

3. After cleaning up and ensuring that there are no impurities on the surface, we can replace the new valve core with accurate holes. Once the position is fixed, the gland nut can be attached and the spool can be turned clockwise until it cannot be moved.

4. Finally, we install the handle according to the position of the hot water, tighten the screws, and press the decorative cap.

Summary. Hello The replacement of the shower switch leakage requires a total of about 50 in general, and more than 100 in good.

Hello The replacement of the shower switch leakage requires a total of about 50 in general, and more than 100 in good.

There is indeed a screw on the back of the closure and the handle to let the potato (the hot and cold water sign is removed), which can be unscrewed to see what is wrong inside, but it is very difficult to repair it, not only do you need special tools to rent by hand, but after unscrewing, you can only see two inlet and outlet channels or valve cores inside.

Hello, it is the converter of the shower that is bad and leaks all the time.

I drew circles and this place has been leaking, I want to know how much it costs to repair?

Broken or what is wrapped in some raw tape.

No, but nothing, it's just leaking.

You can buy a roll of raw tape and wrap it around for a few dollars.

Will there be a leakage in the future? ? Because the inlet of the sluice gate on his side is connected to the toilet flusher in the Tong stove. I just closed that sluice gate bureau in disguise. And then it doesn't leak.

It shouldn't be that this is mainly because there is a gap with raw tape to plug the gap.