Leaking hot and cold water faucet, what to do 50

1. If the hot and cold water faucet is controlled by a main inlet valve, close the main valve. When the hot and cold inlet pipes are separated, then close the corresponding two valves.

2. Use a flat-mouth screwdriver to open the accessories shown in the above picture "01 hot and cold mark (handle fixing screw hole plug)";

3. Use a flat-edge screwdriver to reach into the handle to fix the screw hole plug (hot and cold standard hole), and the counterclockwise (left-handed) screwdriver is about 3 turns;

4. Grab the faucet handle with your left hand, dial it upward, and at the same time use the back handle of the screwdriver (it must be made of non-metallic material, otherwise it will damage the outer surface of the faucet) to gently tap upward, so that the accessory "02 water handle" is separated;

5. Counterclockwise (left-handed) fitting "03 end cap", the end cover is separated from the main body;

6. Put the beginning of the wrench in the hexagonal position of the accessory "04 core tightening hexagonal sleeve", adjust the size of the beginning of the wrench, rotate counterclockwise, remove the ceramic valve core for inspection, if it is intact, clockwise (right-handed), and tighten the upper strength; If damaged, replace the spool with a new one.

7. Replace the accessories "03 end cover", "02 water outlet handle" and "01 hot and cold label (note that red represents the hot water side, blue represents the cold water side)" as it is

The leakage is mostly due to the aging of the valve core, and the ceramic valve core can be replaced, which is mostly available in hardware stores or bathroom stores that sell faucets. First take the color twist under the handle, and loosen it with a hexagonal spoon (some are with a small flathead screwdriver) to remove the handle, and the rest of the work is simple, and the valve core must be positioned correctly when placing it, so as to ensure the seal. Provide single-hole hot and cold water faucet installation diagram for your reference:

Hello, my family is a new faucet at the beginning of the leak, and then I bought 2 yuan of tape (this is specially used to wrap water pipes) to wrap it on the good It is also a hot and cold water pipe, which is the joint of the hot water pipe.

If the connector is not leaking, it is simply that your faucet is leaking and dripping, then the faucet may be broken.

Ten yuan for a single stainless steel is enough, and the hot and cold water faucet like yours is about 100 yuan or more, if there is a sound, it means that there is a problem with the faucet itself There may be scale in it, remove it and put something special to clean the inner core of the water dispenser Try.

In the TV series Wild Duck, the faucet of the doctor's house seems to be making a sound, and then it was changed.

If it's new, it's repaired, it's too old, why bother, spend money on repairing, it's better to buy a new one.

You're not expensive, or change it, you buy it yourself, take a helper, remember to wrap the raw material belt on the screw, we feel that you buy a more cost-effective, you are inside the water seal is broken. If you want to fix the expensive ones, you can't get 34 hundred. I think 200 is enough, you go and dig it out on the Internet.

It's cheap, it's good-looking.

1. Close the water inlet valve.

Remove the small screws on or behind the faucet handle to remove the handle that is fixed to the faucet body. Some screws are hidden underneath metal buttons, plastic buttons, or plastic pieces that snap into or screw into the handle. As soon as you open the button, you will see the handle screws mounted on the top.

If necessary, use some penetrating lubricant like WD-40 spec to loosen the screws.

2. Remove the handle.

Remove the fill nut with large carp pliers or an adjustable wrench, being careful not to leave scratches on the metal. Turn the spool or shaft in the same direction you rotated when you turned on the faucet to unscrew them. Look at the parts of the faucet.

3. Remove the screws that fix the washer.

If necessary, use penetrating lubricant to loosen the screws. Inspect the screws and spool and replace them with new ones if damaged.

4. Replace the old gasket with a new, identical one.

A new gasket that is almost exactly a match for the old gasket will generally stop the faucet from dripping. You also want to notice whether the old washer has a bevel or a flat one, and replace it with the same new washer. Gaskets designed for cold water only expand violently when hot water flows through them, clogging the outlet and slowing down the flow of hot water.

Some gaskets will work in both hot and cold water, but you want to make sure that the gasket you buy for replacement is exactly the same as the original.

5. Install the faucet parts.

Attach the new gasket to the spool and reassemble the parts in the faucet. Rotate the spool in a clockwise direction. Once the spool is in place, reattach the fill nut. Be careful not to leave scratches on the metal with the wrench.

6. Water discharge detection.

Reinstall the handle and put the button or disc back in. Turn the water supply back on and check for any leaks.

This is very cheap, find a plumber, even if you change the full set, it will only be three or four hundred yuan.

Or you can buy a faucet and change it yourself.

The cause of the internal leakage of the fast electric water faucet is the condition caused by the failure of the rubber cushion cap of the electric water faucet.

The solution is: if there is a problem with the rubber pad cap of the electric water faucet, you need to contact professional maintenance personnel in time to repair or replace the rubber pad to solve the problem of internal leakage of the electric water faucet.

In the event of an accident, stop using the electric water faucet immediately. When using the electric hot water faucet, if you find that the indicator light does not turn on the hot water, the sound is abnormal, etc., you must stop using it immediately, turn off the power, contact the manufacturer's maintenance personnel in time, ask professionals to repair, and do not disassemble it yourself.

In general, don't choose to cut corners when decorating and buy something cheap. If there is a problem in the later use, then you may have to disassemble everything and reinstall it. If you have these costs, it is better to buy a good one to install in the kitchen, and it will last longer.

If you want to boil hot water, you must wait for a while before turning on cold water, so that the faucet will not be damaged. The faucet in the kitchen must be of good quality, so that the quality can be guaranteed.

It may be that the hot and cold valves are not properly installed, or it is possible that the shaft gasket inside the faucet is completely worn and damaged, or it is possible that there is a gap between the faucet bolts and a serious water leak.

It is normal for this type of faucet to experience alternating between cold and hot water at the same time, causing problems with the pipes and frequent leaks.

This is because the parts are damaged, not tightened, used inappropriately, and there is still some water in the pipe, and there is a delay.

If the inside of the electric hot water faucet is leaking, it is necessary to find out where the water is leaking. The leakage is different, and the reasons are different. If the hot water leaks, and the cold water does not leak, it is the internal adhesive film that is damaged or slippery.

If it is boiled until cold water and hot water will continue to leak. It may be that the casing is broken, or the internal thermal protection column is broken, and the rubber ring is not placed or loose. It is recommended that you contact the manufacturer to see if you can return to the factory for inspection and maintenance.

It's also safe to use.

The position of the last ** is right, the pliers are not good, find a wrench should be able to unscrew, to twist counterclockwise.

The last position is right, it is easier to find a wrench to screw, the valve core shop sells ** about 5 pieces, and the new faucet ** about 100. It can be replaced with a single handle, which is a two-handed wheel.

The second pair of wrenches, pay attention to the direction of rotation of the new valve core when buying the valve core, there is a difference between the left and right.

Is this old-fashioned (hot and cold separately regulated) mixing valve still worth repairing?

It's not easy to use. It is recommended to replace the mixing valve.

1.Causes of leaking hot and cold water taps.

1) If the water outlet is leaking, it may be that the axial gasket in the faucet is worn, you can use pliers to loosen the gland and remove it, and then take out the axial gasket and replace it with a new axial gasket.

2) If the gap between the faucet is leaking, it should be that the triangular gasket in the gland is damaged, first loosen the screws, remove the tether, then loosen the gland and remove it, take out the triangular gasket on the inside of the gland, and replace it with a new triangular gasket.

3) If there is water leakage at the receiving joint, the cap nut should be loose, and the cap nut can be tightened from the beginning, if not, it should be the U-shaped gasket worn and replaced with a new one.

2.Hot and cold water faucet leak repair steps.

1) If the hot and cold water faucet is operated by a main water inlet valve, close the main valve first; If the hot and cold inlet pipes are separated, the two corresponding valves need to be closed.

2) Use a flat-mouth screwdriver to open the hot and cold mark, use a flat-mouth screwdriver to reach into the handle to fix the screw hole, and extend it into the hole of the hot and cold mark, and the screwdriver rotates 3 times in the counterclockwise direction.

3) Then grab the faucet handle with your left hand, dial it upwards hard, and tap it upwards with the handle at the back end of the screwdriver, first separate the water outlet handle, and then remove the end cover in a counterclockwise direction, so that the end cover is separated from the main body.

4) Use the adjustable wrench to place the hexagonal position of the hexagonal sleeve tightly in the core, adjust the initial size of the adjustable wrench, rotate counterclockwise, remove the ceramic valve core and check, if it is normal, install it in the clockwise direction; If damaged, replace the spool with a new one.

5) Refer to the faucet installation method, the end cover, water dispensing handle, hot and cold standard are installed, red represents hot water, blue represents cold water, don't make a mistake.

Question 1: How to repair the leakage of the hot and cold water faucet The leakage is mostly the aging of the valve core, and the ceramic valve core can be replaced, which is mostly available in hardware stores or bathroom stores that sell faucets. First take off the color twist under the handle, and loosen it with a hexagon spoon (some are with a small screwdriver) to remove the handle of the hand beam, and the work behind it is simple, and the valve core must be positioned correctly when placing it, so as to ensure the sealing.

Provide single-hole hot and cold water faucet installation diagram for your reference:

Question 2: How to fix the leaking hot and cold water faucet in the kitchen? The hot and cold water faucet in the kitchen is leaking, and the mat can be changed or replaced with a new one.

First, the cause of the failure:

1. The leakage of the hot and cold water faucet in the general kitchen is caused by the aging and wear of the sealing gasket inside the faucet after a long period of use.

Second, maintenance methods:

1. Just disassemble the faucet and replace it with a rubber or silicone pad. 2. Just buy a new faucet spool and replace it.

3. Replace the entire faucet directly.

Question 3: What should I do if the cold and hot water faucet is leaking The repair method of cold and hot water faucet leakage If you understand it and have strong hands-on ability, you can bring it with you to replace the valve core. Generally, ten dollars can be done.

Question 4: What should I do if the kitchen hot and cold water faucet is leaking, and how to repair it ......This is ...... normalBecause the meeting rotates to wear out ......Generally, it is to give him a pressure and not to leak ......So ......You should change ......You can't fill the seams.

Question 5: What should I do if the hot and cold water faucet at home is leaking Turn off the main valve at home, and then buy a new one and replace it, remember to pay attention to safety.

Question 6: How to fix the leakage of the hot and cold water faucet The cold and hot water faucet (whether it is a water mixer) is leaking, just remove it and replace it. If you have the ability to do it, remove it, check whether the sealing gasket is damaged, whether there is dirt (such as scale) in it, and then see if the ceramic piece is worn, if so, it can only be replaced.

Question 7: How to deal with the leakage of the hot and cold water faucet in the bathroom The last position is right, it is easier to find a wrench to screw, and the valve core shop sells ** about 5 yuan, and the new faucet ** is about 100. It can be replaced with a single handle, which is a two-handed wheel.

Question 8: Can the rotating handle of the kitchen sink hot and cold water faucet and the faucet body leak out? …This is ...... normalBecause the meeting rotates to wear out ......Generally, it is to give him a pressure and not to leak ......So ......You should change ......You can't fill the seams.

Question 9: Will there be water leakage if only one hot and cold water faucet is installed, and the other unneeded one can be plugged with a plug!

Question 10: What should I do if the hot and cold water faucet is leaking Turn off the main valve at home, and then buy a new one and replace it, remember to pay attention to safety.