What should I do if my neighbor s bathroom is not waterproofed, and my walls are wet and peeling?

The solution is to knock down the wall of the neighbor's house, and then do a good job of waterproofing and then re-tiling it to treat it from the source; If you peel off the skin on your side, you need to shovel off the original wall ash layer, and then do moisture-proof, dust-proofing, and latex paint.

Redo it just in case and don't add to the troubles later.

Start by finding a property and renovation company.

If it is caused by water seepage on the wall of the neighbor's bathroom, the owner and the property management office will come forward to find him at the neighbor's house, call him to your house to investigate and discuss solutions, and discuss part of the cost. After all, if you only go to your neighbors, sometimes you will rely on it, and you can only be notarized by the property management office, and they will give the cause and solution of water seepage, so as to avoid the intensification of conflicts between neighbors and easy to quarrel.

This relationship must be done well, generally there is such a situation, if the upstairs is not reasonable, there is no way to solve it, only through the property or community branch committee to solve this kind of thing, through them to negotiate this matter, life will inevitably encounter some problems, I hope that the neighbors who live together are for the sake of others, don't be so selfish, so that you can get along well.

In this case, you can ask the upstairs to be re-waterproofed and compensate for your losses, and if not, you can also sue the court to solve it.

Because the putty is alkali copy, it will return to alkali after water, and the wall is prone to yellow traces after drying, especially at the junction of wet and dry walls, the traces are the most obvious. In the past, the putty used for decoration may appear moldy on the wall, but now the anti-mold putty is mostly used in construction, and the wall will generally not be moldy after the water is wet.

The same method is used to repair the alkali return and moldy walls, first use ordinary sandpaper to sand off the alkali or moldy parts, and then repaint. If the wall has begun to peel, peel, and bubble, in most cases, the putty should be removed and repainted.

When repairing the wallpaper wall, tear off the damaged wallpaper and directly brush the wallpaper glue and paste the wallpaper. Repair the damaged latex paint wall to shovel putty first, putty after the putty is cleaned, then scrape the putty three times, and finally brush the primer twice over the topcoat, compared with the new house decoration paint, just more than the process of shoveling the putty.

Generally speaking, whether it is a wallpaper wall or a latex paint wall, there is no need to level the wall again, unless the flatness of the wall is destroyed when removing putty or removing wallpaper.

If the wall is damp, it is normal to say that the local source climate is relatively humid or the back of the damp wall seeps water in the past, which causes the wall to be damp, you can deal with it like this.

1. Thoroughly clean the peeled and damp wall with a shovel.

Please click Enter a description.

2. Continue to remove the floating ash on the wall to prevent the floating ash from affecting the bonding strength.

Please click Enter a description.

3. Evenly brush the separator with a brush and apply it 2-3 times, with an interval of about 3 hours between each time.

Please click Enter a description.

4. After the isolator is dried, the putty can be scraped in batches, and the batch scraping time is not less than 24 hours each time.

Please click Enter a description.

5. After the putty is dried, carefully polish it with No. 180 sandpaper.

Please click Enter a description.

6. Clean the surface dust and paint latex paint 2-3 times, with an interval of about 6 hours between each time.

Please click Enter a description.

First of all, if the wall has been waterproofed, it is necessary to consider that the wallpaper on the outside of the toilet has poor air permeability and no moisture.

The plate volatilizes out, which leads to the production of bacteria, so that it will peel. The second is the waterway pressure, which can eliminate the problem of the waterway without continuous pressure loss. It is also possible that the sand layer of the tiles is too thick, the ground is too wet, and the tiles are not dried out, and when the temperature rises, water vapor will come out under the tiles, which will spread along the corners of the wall, causing the wall to peel.

First of all, do a good copy.

The waterproofing of the bathroom includes the waterproofing of the walls (the shower area is done bai to the roof; du other positions to be 30cm high); Then shovel the damp wall decorations, wait for the wall to dry (generally need to be ventilated for more than 24 hours), and then paint a single layer of cement-based waterproof paint on the wall to prevent moisture, and then decorate on the waterproof layer.

Ventilate your home and bathroom, and if you don't have one, open a window to allow air to flow. Otherwise, no matter how much you repair the wall, it will be a symptom rather than a cure.

@这个是因为卫生间渗水照成的, first you need to do a good job of waterproofing the bathroom, then remove the peeling walls, brush the separator again, and then make up with putty. I know a product that works very well, you go search for the black gold steel waterproof guard.

Shovel off the outside paint to make a layer of waterproofing, you can choose to redesign, stick wall tiles or consider the mirror, I don't know if the bathroom has an exhaust fan or window, the bathroom needs to be ventilated frequently, otherwise the re-paint will still return to moisture!

Remove the tiles in the bathroom, do a good job of waterproofing, remove the walls of the room, repaint or paste wallpaper.

This is that the waterproofing of the wall is not done, and there is often a fever in the suite, so you can only find a professional decoration worker to do waterproof treatment for you!

Shovel off, brush with waterproof glue, and lay wallpaper.

1. What should I do if the bathroom is waterproof and the exterior wall is peeled?

1. First of all, check what causes the wall to peel in the bathroom, if the wall is wet and seepage, first solve the problem of water seepage, and see if the tile gaps in the corner are complete and whether the water pipe is broken.

2. After solving the problem of water seepage, first remove the loose peeling place.

3. Clean up and brush the separator 2 times, each time with an interval of 3-5 hours after drying the putty in batches every other day, and the putty is polished and smoothed after hanging for about 6 hours, and then brush the latex paint, 2 3 times, with an interval of more than 3 hours each time.

2. How to do a good job of waterproofing the bathroom?

1. The bathroom floor is leveled first.

If you want to replace the floor tiles in the bathroom, you can chisel the original floor tiles, and after chiseling, you must first level the ground with cement mortar, and then do waterproof treatment. This avoids leakage of water-repellent coatings due to uneven thickness.

2. The seams should be painted in place.

The joints between the walls and floors of the bathroom and the joints between the water and water pipes and the floor are the most problematic places. In the process of construction, we must urge the workers to deal with these corners and corners, and all the waterproof coatings must be applied "in place".

3. Wall treatment is also very important.

In the waterproofing treatment of the general bathroom, the waterproof coating on the wall should also be about 30 cm high to prevent water from penetrating into the wall. However, if the wall of the bathroom is a non-load-bearing lightweight wall, the entire wall needs to be coated with waterproof paint. If you are using a two-fan shower screen, the two walls connected to each other must also be fully painted.

If you are using a bathtub, the height of the waterproof coating on the wall adjacent to the bathtub must also be higher than the upper edge of the bathtub.

4. Keep the water smooth.

All sewer pipes in the bathroom, including drains with floor drains and sanitary ware, must be kept unobstructed. Only in this way can we fundamentally avoid the tragedy of the "flooding of the Seventh Army."

In this case, it is necessary to throw away all the tiles of the bathroom, and re-glue the tarpaulin on the floor and wall of the bathroom, and then re-paste the tiles.

Exterior wall peeling is not necessarily caused by the indoor bathroom waterproofing is not done well, it is recommended that you ask a professional master to find the cause of the exterior wall peeling caused by slow seepage from whether there are cracks in the exterior wall, and wish you health and happiness.

The waterproofing in the middle is not done, and the exterior wall is peeled, which can be waterproofed again with the bathroom belt, so that it can be solved.

You can first clean up all the outer skin, clean it up and then fill it with the original material, and finally make the bathroom waterproof again.

What should I do if the bathroom waterproofing is not done well and the exterior wall is peeled? This is not possible, you have to find a waterproof worker. Go on. Do waterproofing until it does not leak.

It is recommended to find someone from a professional renovation company to give advice and solutions, and solving it by yourself may not be able to achieve the desired effect.

What should I do if the bathroom waterproofing is not done well and the exterior wall is peeled? I think it should be dried, the skin scraped off, and waterproofed again.

I can only get it off again, and I did it well, and it's a very long place to compare this

Waterproofing of the bathroom is an important step in our home decoration process. If the waterproofing is not done well, it will bring endless trouble. It not only affects our daily life, but also brings inconvenience to the neighbors upstairs and downstairs, and also affects the harmonious relationship between neighbors.

Today, I will tell you what to do if the bathroom is waterproof and the exterior wall is peeled?

It is necessary to chisel the surface of the bathroom with a decorative layer such as a brick, etc., after leveling the base surface, paint the JS coating film waterproof layer, and then restore the paving of the surface brick.

Toilet safety tips: toilet waterproof remedies.

1. The original waterproof layer can not be destroyed: the common reason for leakage in the general bathroom is that the original waterproof layer is destroyed, which is the most likely to occur when redecorated, so it is also necessary to pay attention, if it is accidentally damaged, it should be repaired in time, so as not to cause these hidden dangers behind.

Second, the wall waterproofing can not be ignored: the toilet water consumption is very large, and the shower is easy to splash water on the wall when bathing, so the wall should be waterproofed when the wall tiles are laid. Ordinary walls require a waterproof height of 30 cm, and non-load-bearing light walls should be waterproof to a meter high, so the waterproof height and precautions of the bathroom are also very important.

The unified standard for the construction of the project is that the four walls are meter-high waterproof, which is to prevent future maintenance from causing trouble to the owner.

1. There is a leakage problem in the water pipe in the wall, which makes the wall root damp, in this case, the wall should be chiseled, and then the water pipe should be repaired, the leakage point should be found, and the new pipe fittings should be replaced. 2. During the construction of the waterproof layer, there are gaps in the wall, and the root will appear peeling after a long time, at this time, it is necessary to apply waterproof protection at the peeling place to achieve the waterproof effect, but it is best to redo the waterproof layer, so as to ensure the quality of waterproofing.

Relevant information: 1. If the waterproof material is not applied to the ground leveling project, there will be too much material used in some places during construction, and too little material will be used in some places, so that the problem of water leakage will easily occur in the light and thin places.

2. When carrying out wall waterproofing projects, the joints may not be treated in place, which will lead to many problems in the future, especially the peeling of the root of the wall.

3. Then check the height of the water on the wall, especially the shower, you need to paint the entire wall, and the toilet and other areas are 30 cm enough.

4. The tiles in the bathroom are easy to stick to dust, if they are not cleaned in time, it will lead to more and more accumulation, and it is very troublesome to clean up in the end. Therefore, usually, you can use laundry detergent to mop and wash the bathroom tiles every few days. If you are using vitrified tiles, you can dispose of them by scrubbing them directly with a damp cloth.