Installation skills of home squatting toilets, how to install toilet squatting toilets

1. Assemble the drainage pipe first, connect the 2 straight pipes, and then connect the elbow pipes. Install the entire drain to your old pipe location. If you keep the old tube and do not replace it, you can ignore this step.

On the left is the drain valve, and on the right is the inlet valve. Screw the drain valve and inlet valve into the inside of the water tank, make sure that there is no problem, and lock the upper cover of the box.

2. Find the hook and put it on the wall, draw two holes, and drill the screws. Snap the hook onto the back of the tank. Attach the hooked tank to the two screws. Place the tapered rubber ring on the connecting cup, connect the cup to the drain pipe, and then tighten the drain pipe at the bottom of the water tank.

3. Basically, you only need to connect the hose to the water inlet of the water tank. When you're done, it's time to test flush. If there is a water leak, you can check the installation manual for installation errors.

This one seems to be a problem with the squatting toilet you bought; The squatting toilet itself is divided into front drain and rear drainage, and the seller didn't tell you the difference when you bought it?

You see if the drainage hole of your squatting toilet is on the side of the water inlet pipe, if it is on one side, it is the renovation company's fault, you can ask them to rework compensation, if it is the opposite side is that the squatting toilet you bought is the front drainage, then you can only admit it.

If you are really afraid of smell, add a plastic ball, which will not affect the flushing of the stool, and the smell can also be blocked.

You put the draining pipe not with that water hole.

In order to be more safe and hygienic, some owners will install a squatting toilet in the public bathroom at home, if you want to use the squatting toilet normally, you must pay great attention to the installation and construction of the squatting toilet, so how to install the toilet squatting toilet? Let's take a look at this article below.

How to install a toilet squatting toilet.

1. Before installing the squatting toilet, you should first determine the specific installation location and actual size of the squatting toilet. Secondly, according to the sewage outlet of the squatting toilet you purchased, you should reserve a pipe for discharging sewage at the appropriate location from the wall, and you must remember to keep an appropriate distance between the pipe entrance and the ground.

2. Next, the installation position should be dug into a pit, and the depth of the pit must be higher than the height of the squatting toilet, so that it will be more convenient to install the squatting toilet in the later stage.

3. Then the connecting rubber plug should be inserted deep into the water inlet hole of the squatting toilet, and it should be clamped. It is also necessary to apply some glass glue to the outer edge of the water inlet hole of the squatting toilet for sealing, and then insert the water inlet pipe into the connecting rubber plug, so that the water inlet pipe can be well sealed with the connecting rubber plug, so as to avoid water leakage when using the toilet in the later stage.

4. Then apply some glass glue to the edge of the outlet of the squatting toilet, and then put the squatting toilet into the inlet of the sewage pipe for screwing, and then use coke slag and other fillers to fill the squatting toilet, so that the squatting toilet can be erected more horizontally, and there will be no tilting and instability.

5. After installation, the squatting toilet should be tested to see whether the connection positions of the squatting toilet are installed correctly and whether there is any water leakage. If a leak is found, the leak should be repaired.

6. If no water leakage is found, the perimeter of the squatting toilet should be filled tightly with fillers. When filling, you should also apply about one centimeter of asphalt at the point where the cement mortar and the ceramic are in contact, so that the squatting toilet can be better used in the future.

7. Then use cement mortar to fix the squatting toilet on the ground, when the squatting toilet becomes very stable and firm, you can try to press the water tank button to see if the flushing is normal, if Qinghuai is not abnormal, it means that the squatting toilet is successfully installed and can be used normally. Then you can start to work on the tiles on the floor, so that the bathroom can be more waterproof and look more beautiful.

The above is a detailed introduction to how to install the toilet squatting toilet, I hope it can help friends in need. In order to ensure that the squatting toilet can be used normally, it is recommended that you should ask professionals to help install the squatting toilet.

When decorating and designing, many people will be concerned about whether the bathroom at home is better to install a toilet or a squatting toilet and feel distressed, presumably this is also a problem that everyone has been worrying about. Under normal circumstances, many people will want to install a toilet, but considering the problem of practicality, it is better to have a squatting toilet, and here we will teach the specific steps of how to install a squatting toilet when decorating the design!

1. First of all, we must find the installation location of the squatting toilet, and then leave a pipe here, but remember that the water pipe must be kept at a certain distance from the ground.

2. After finding a good position, the next thing to do is to make a pit, which must be higher than the squatting toilet, so that it will save time and effort when installing it in the later stage.

3. You must seal the water inlet hole of the squatting toilet, and then all you have to do is to insert the water inlet pipe into the water inlet hole, so as to avoid water leakage in the future use process.

4. Of course, the side of the squatting toilet should also be coated with glass glue, and of course, some fillers should be used to stabilize the squatting toilet well.

6. After the test, if you find that there is no water leakage, the last thing to do is to fill, but you must pay attention to the place where the cement slurry and the ceramic are in contact, you must smear some asphalt, so that it can be better used in the future.

7. After the installation, the next step is to paste the tiles, so that it can be more beautiful.

8. You can take a look, this is the squatting toilet after installation, and finally you can try to flush the water to see if it is suitable, and it should be noted that the water trap should be installed, so that it can be better deodorized in the future.

The squatting toilet needs to smash a pit out of the ground, and then bury the squatting urinal into it, and the top of the squatting urinal should be level with the ground. So this ordinary person can't take it, and you need to ask a professional to help you.

1.Determines the distance of the sewer inlet from ground level.

2.Reserve a pit under the ground for the installation of a squatting urine.

3.Place the connecting rubber plug into the water inlet hole of the squatting toilet and clamp tightly.

4.Set the toilet horizontally.

5.Open the water inlet system and check the joints for water leakage.

6.After checking that there is no water leakage at each joint, fill the area around the toilet with filler.

7.Fix the squatting toilet with cement mortar.

8.Test flushing, if there is no abnormality, you can use it.

First of all, it is necessary to determine the distance between the entrance of the sewer pipe and the ground, reserve the pit on the ground to install the squatting toilet, put the connecting rubber plug into the water inlet hole of the squatting toilet, clamp the toilet to the level, open the water inlet system, check whether there is no water leakage everywhere, and if there is no water leakage, use flat flushing, and mistakenly sweeten the cement slurry around the toilet. Secure the squatting toilet.

Determine the entrance of the sewer pipe, the distance from the ground, the second pit reserved for the installation of the squatting device under the ground, the third will put the connecting rubber plug into the hole, and the toilet will be set up horizontally and open the water purification system. After checking that there is no water leakage at the joint, use the filler to fix the squatting toilet around the toilet with cement mortar to test the water, if there is no abnormality.

We use the squatting toilet every day, but when we buy it back, we don't know how to install it, so is there a simple and easy-to-operate installation guide? The following decoration security network shares with you the installation method of squatting toilets.

Before installing the squatting toilet, we must first prepare the tools to use, such as raw material tape, glass glue, oil trapped mud, tape measure and leveling scale, etc.

Here are the steps to install the squatting toilet:

1.According to the sewage outlet of the installed product, reserve the sewer pipe at the appropriate position from the wall, and determine the distance between the sewer pipe inlet and the ground level.

2.The depth of the pit reserved for the installation of the squatting toilet under the ground is greater than the height of the toilet.

3.Place the connecting rubber plug into the water inlet hole of the squatting toilet and clamp tightly. Apply a layer of glass glue or putty to the outer edge of the water inlet hole of the squatting toilet, and insert the water inlet pipe into the water inlet hole of the rubber plug so that it is well sealed with the rubber plug to prevent water leakage.

4.Apply a layer of glass glue or putty to the edge of the outlet of the squatting toilet, put it into the inlet of the sewer pipe and screw it together, and set the toilet level with coke residue or other filling.

5.Open the water inlet system and check each joint for water leakage, and if there is a water leak, check the condition of each joint. until the problem is resolved.

6.After checking that there is no water leakage at each joint, fill the toilet around with filler, and fill the contact surface between the ceramic and the cement mortar with an elastic material such as asphalt or linoleum of more than 1cm.

7.Use cement mortar to fix the squatting toilet in the horizontal plane, and after it is stable and firm, then pave the bathroom floor tiles on the cement surface.

8.Test flushing, if there is no abnormality, you can use it.

Finally, precautions for installing a squatting toilet:

1.All parts of the squatting toilet that come into contact with concrete should be filled with elastic materials such as asphalt or linoleum, otherwise the toilet will break due to cement expansion.

2.When finishing with heat-dissolved asphalt, it is necessary to prevent the toilet from bursting due to heat.

3.The installation of the toilet should be operated in strict accordance with the instructions, otherwise the toilet will be broken.

4.The squatting toilet water flushing device mainly includes ball valve, high water tank flushing, electric bright enlightenment magnetic induction flushometer, delay flush valve, manual flush valve, etc.

The above is the installation method of the squatting toilet introduced by the decoration security network for you, I hope it will be helpful to you.

What are the specifications of a squatting toilet? The height of the squatting urine.

How to install the squatting toilet.

Top 10 brands of squatting toilets.

Classification and purchase method of squatting toilet.

Squatting toilet tank size Squatting toilet water tank principle.

What should I do if the squatting toilet is blocked, I'm here to help.

There are two major matters to pay attention to in the transformation of squatting toilets.

The installation method of the squatting toilet must first prepare the commonly used materials and tools, such as raw material belt, glass glue, oil sludge, tape measure and level, etc., and then you can start to install, the steps are as follows:

1. When installing the squatting toilet, the sewer pipe should be reserved at the appropriate position from the wall according to the sewage outlet of the installed squatting toilet, and the distance between the sewer pipe entrance and the ground level should also be determined.

2. When installing the squatting toilet, it is required to reserve the depth of the pit under the ground, and remember that the depth must be greater than the height of the squatting toilet for dry installation.

3. Put the connecting rubber plug into the water inlet hole of the squatting toilet and clamp it tightly, apply a layer of glass glue or putty on the outer edge of the contact with the water inlet hole of the squatting toilet, and insert the water inlet pipe into the water inlet hole of the rubber plug to make it well sealed with the rubber plug to prevent water leakage.

4. During installation, it is necessary to coat a layer of glass glue or putty on the edge of the outlet of the squatting toilet, put it into the inlet of the sewer pipe and screw it, and use coke slag or some other fillers to erect the squatting toilet horizontally.

5. After installation, open the water inlet system for testing, check whether there is water leakage outside each joint, if water leakage occurs, you need to carefully check the situation outside each joint until the problem is solved.

6. After checking that there is no water leakage, you can fill the area around the squatting toilet with filler, and at the same time fill the contact surface between the ceramic and the cement mortar with elastic materials such as asphalt or linoleum of more than 1cm. Use cement mortar to fix the squatting toilet in the dry horizontal surface, and the floor tiles can be paved on the cement surface after it is stable and firm. Try flushing again, if there is no abnormality, you can use it.

Take off your pants, squat down, solve the problem, get up and put your pants on, and flush the toilet. Complete.

Toes to the hole.

Heel to the hole Poop will make a splash when it goes down.

Bathroom squatting toilet installation turned out to be so simple.

First of all, you have to raise the ground, and then install it when you are high enough, and squatting requires a height.

The installation steps are as follows:

1. The sewage outlet of the squatting toilet and the reserved mouth of the downspout are coated with adhesive or cement. Connect the sewage outlet of the squatting toilet with the reserved opening of the downspout, and correct the position of the squatting toilet. Brick to fix the squatting toilet, to reserve a gap for filling the gravel.

2. After the binder is dry, test the flush into the squatting toilet to observe whether the interface is leaking. Fill the ground with gravel soil between the ground and the squatting urinal, and it is strictly forbidden to really enter the cement concrete. Close the gap with bricks. Cement mortar on the outside of the bricks and paste tiles.

3. The flush valve installed with the squatting toilet is divided into: hand-pressure flush valve and foot-operated flush valve.

4. The water tank installed with the squatting toilet, the installation height of the water tank is meters away from the water circle of the toilet, and the water pressure is required.

When the squatting toilet is installed, the minimum distance between the drainage hole and the wall is 40cm, but the specific depends on whether the squatting toilet is the back or bottom water.

Before choosing a squatting toilet, you must determine the distance between these aspects: 1: the distance from the center of the water inlet to the wall is 60 mm, and the thickness of the body of any part should be 6 mm.

2: Sanitary ceramic water seal depth with integral water trap: >50 mm (conventional reserved clean wall).

3: 650-700mm from the wall behind the squatting stool, (the flushing pipe is a bit short and needs to be lengthened if it is farther away).

The side is not less than 450mm, and the regular reserved net wall is to sit on the toilet, and the back is 300mm away from the wall, and the side is not less than 500mm

PS: The distance between the center of the toilet is generally as follows: mm).

Stick a schematic diagram of the installation size of the squatting toilet for reference during installation.