What should I do if I want to bend the aluminum plastic pipe?

You can put it in a hot environment, or you can choose to use pliers, and then choose the angle that suits you and bend it.

It can be heated, and after heating, it can be bent, or directly select some curved tracks and select some converters.

The most common way is to fill it with some sand, and then plug the opening next to it, heat it accordingly, and then you can slowly bend it.

You can fill it with less sand and plug both sides. It is heated and finally it can be bent.

Just go to the mall to buy it, and now many places are selling this kind of curved aluminum-plastic pipe, and the price is more reasonable.

Generally speaking, as long as the selected pipe can meet the standard, the spring pipe bending tool can be bent arbitrarily according to the construction requirements. But to be in place at one time, you must not bend the pipe more than once in the same position. Directly clamp the aluminum-plastic tube with pliers, and then gently break it downward, and bend it slowly with gentle force, don't use force suddenly, it is easy to break it.

Construction preparation: carefully read the product manual, be familiar with the drawings, formulate the best construction plan, and explain to the workers in detail. Install the model room first, be familiar with the operation process, summarize the operation essentials, and then fully roll out after passing the inspection.

The small bending radius of the aluminum-plastic pipe is 5d (9d is the diameter of the aluminum-plastic pipe), and the bending radius should be mastered, too large will affect the appearance, and too small the inner core will be damaged. When bending, be sure to insert the inner spring, and then put it on the mold to bend lightly, and hammer it with a rubber hammer.

The bending degree of the aluminum-plastic pipe is 5d of the outer diameter of the pipe. For example, the aluminum-plastic pipe of 1216, we also call it 4 pipes, the outer diameter of the pipe is 16mm, and the minimum arc of the pipe is a circle with a diameter of 5*16mm. If you want to bend it again, you need to use the bending spring of the aluminum-plastic pipe.

However, the water is also bent to 90 degrees, so you have to be a little careful when using it. Professional should use inner bend yellow or outer bend yellow, so that the pipe can be bent at the smallest angle possible, if you bend it directly by hand, it will be used to bend, which will cause the aluminum layer inside to break and so on.

The aluminum-plastic pipe cannot be bent directly at 90 degrees, and it is easy to deform the pipe to affect the water pressure, and in serious cases, it may block the nozzle, so the 90 degrees of the aluminum-plastic pipe is generally formed through the joint. You can buy a pipe spring smaller than the inner diameter of the aluminum-plastic pipe from the hardware store, tie a threading wire, pull the pipe spring into the elbow of the aluminum-plastic pipe, and you can bend the pipe at both ends of the pipe. Directly clamp the aluminum-plastic tube with pliers, and then gently break it downward, and bend it slowly with gentle force, don't suddenly exert force, it is easy to break it and so on.

I think that if we want to bend the aluminum-plastic pipe, we should do a good job of design in advance, and then adopt a scientific and reasonable method to let the construction workers carry out the construction according to our design.

Professionals should use inner bend yellow or outer bend yellow, so that the pipe can be bent at the smallest angle possible, and if you bend it directly by hand, it will be used to bend, which will cause the aluminum layer inside to break.

First of all, these aluminum-plastic pipes should be heated, and after reaching a certain level, they can be directly bent, and finally cooled.

In the process of decorating the house, we use more and more pipe materials, such as aluminum-plastic pipes.

Usually aluminum-plastic pipes are generally used for heating, many people know that the material of aluminum-plastic pipes is particularly hard, if you want to bend aluminum-plastic pipes or it is more difficult, so what should you do if you want to bend aluminum-plastic pipes? Let's take a look.

1. What should I do if I want to bend the aluminum-plastic pipe?

In the process of decoration, if you want to bend the aluminum-plastic pipe, you can use the tool of spring bending to bend it, or you can directly use pliers.

Clamp the aluminum-plastic pipe and gently break it downward, so that it can also be bent by the aluminum-plastic pipe, but it should be noted that when breaking the aluminum-plastic pipe, it must be bent slowly with gentle force, if the force is too large or too fast, it is easy to break the aluminum-plastic pipe, and there is another point to pay attention to, that is, the degree of bending the aluminum-plastic pipe should not be too large, for example, do not bend it directly to 90 degrees, which will easily lead to the deformation of the pipeline, and in serious cases, it will also block the nozzle.

Therefore, when you want to bend the aluminum-plastic pipe at 90 degrees, you need to complete it through a joint.

2. What should I pay attention to when using aluminum-plastic pipes to make floor heating pipes?

1. If we usually use aluminum-plastic pipes to make floor heating pipes, we should pay special attention to the selection of materials, because it depends on whether the specifications and sizes of the pipes meet the relevant regulations.

2. In addition, when using aluminum-plastic pipes to make floor heating pipes, it is also necessary to pay attention to determining the spacing between the pipes, because the water temperature of the radiator volume will be particularly high, so in order to ensure that the service life of the pipe can be extended, and in addition, in order to avoid the floor temperature being too high, when using a small heat exchanger to convert the water supply temperature, the spacing between the aluminum-plastic pipes should be calculated according to the specific situation.

Gas aluminum-plastic pipe is a material commonly used in gas pipeline system, which has the advantages of corrosion resistance, high pressure resistance, and wear resistance. However, due to its special structure, it is relatively difficult to bend. This is due to the fact that the aluminum-plastic pipe is composed of an inner plastic pipe and an outer aluminum pipe, and there is a layer of adhesive between the two, which makes the pipe have a certain rigidity.

To bend the gas aluminum-plastic pipe, you need to use special tools and skills. Here are some of the reasons that can cause bending difficulties:

1.Pipe diameter and wall thickness: Pipes with larger diameters and thicker wall thicknesses are more difficult to bend because they are more rigid.

2.Bending angle: Smaller bending angles are easier to achieve, while larger bending angles require more strength and skill.

3.Bending radius: The smaller the bending radius, the more difficult it is to bend. A bend radius that is too small can cause the pipe to deform or rupture.

4.Temperature control: During the bending process, the temperature of the pipe needs to be controlled. Too high a temperature may cause the plastic to soften, while too low a temperature may cause the aluminum tube to become brittle.

If you need to bend gas aluminum-plastic pipes, it is recommended that you consult a professional pipe installer or use specialized tools and techniques to do it. This ensures that the bending process is completed safely and correctly, avoiding pipe damage or safety hazards.

Summary. It can be straightened by extrusion of the aluminum tube, which belongs to the key to the serious bending of the aluminum alloy tube, and the staff of the aluminum tube straightening need to pay attention to the strength used in the straightening, and the force is too large to easily cause the aluminum tube to deform, close and orange peel and other phenomena, and the force is too small to cause the aluminum tube to be not straightened.

The large material and the two ends of the tube material in the aluminum tube are not easy to cause bending, but the two ends of the material drawn out by the small material and the plane die are very easy to cause bending, for this reason, it is necessary to move to the middle of the two ends to lift the material and pack the frame, if this is not up to the standard, the structure needs to be adjusted, that is, the large material is placed in the profile that has been aged and lifted to the frame.

What to do if the aluminum tube flaring is bent.

It can be straightened by extrusion of the aluminum tube, the straightening belongs to the key to the serious bending of the aluminum alloy tube, the staff need to pay attention to the strength used in the straightening, the force is too large and it is easy to cause the aluminum tube to deform, close and orange peel and other phenomena, and the force is too small The aluminum tube will not be straightened The large material in the aluminum tube and the frame at both ends of the tube material with the tube are not easy to cause bending, but the two ends of the material drawn out by the small material and the plane die are very easy to lead to the bending, for this reason, it is necessary to move closer to the middle of the two ends to lift the material and pack the frame, if this does not meet the standard, It is necessary to adjust the structure, that is, to put the material in the profile that has been aged and lift it into the frame.

In order to prevent or reduce the occurrence of elbow defects and obtain satisfactory elbow quality, corresponding countermeasures need to be taken to solve them during the elbow machining process. First of all, aluminum tube manufacturers should design the bending tube with the largest possible bending radius within the scope allowed by the product design structure. At the same time, when selecting equipment, aluminum tube manufacturers should choose a pipe bender with a lateral lifting and tail end pushing mechanism.

Hope the above helps you a little! Thank you.

It is very likely that the motor and the model do not match, many people want to change the motor cheaply or use the motor that does not match the model, it is recommended to go to a more professional place.

Springs with elbows.

Aluminum-plastic pipe is a new type of pipe made of co-extrusion and compounding. Polyethylene is a non-toxic, odorless plastic with good impact resistance, corrosion resistance, and weather resistance. The middle layer of longitudinal welding aluminum alloy makes the pipe have the compressive strength of metal, and the impact resistance makes the pipe easy to bend.

The aluminum-plastic composite pipe has the two characteristics of strong pressure resistance of metal pipe and acid and alkali corrosion resistance of plastic pipe, which is a model of a new generation of pipes. Aluminum-plastic pipe (aluminum-plastic composite pipe) is a more popular pipe on the market, the current market is more famous Rifeng, Jinde and Meifeng, because of its light weight, durability and convenient construction, as well as aluminum-plastic pipe (aluminum-plastic composite pipe) bendability is more suitable for use in home decoration.