As soon as I turn on the side of the hot water faucet, it leaks, what is the reason?

It has to do with the water heater you're using.

If it's a solar water heater.

The hot water flows out by the potential energy of the hot water tank, and the cold water flows out by the pressure of the tap water, and the pressure of the two is different;

If using a gas or electric water heater.

Hot water flows out by the pressure of cold water entering the water heater, which is the system pressure of tap water. At this time, hot water and cold water belong to the same system, the pressure is the same, and the flow rate is proportional to the pipe diameter, you check the pipe diameter.

The hot water faucet is cold water on one side and hot water on the other, if the side leaks, it may be that the lid is loose, or it is possible that the gasket inside is broken, it is recommended to replace the faucet in the case of power failure.

It depends on the leakage of the **, and you can see it with your eyes.

If water leaks from the root of the faucet, it means that the faucet is not installed tightly, or there is no water stop.

If there is a leak from the outlet of the faucet, it means that the outlet of the faucet is not properly installed and needs to be tightened or a waterstop is used.

What causes a leaking water heater? Most of them have problems here, and they can be solved without changing any accessories.

It may be caused by the poor quality of the electric water faucet itself, and the solution: replace it with a better quality brand; It may be the leakage caused by the static electricity of the faucet, the solution: install insulation materials around the faucet to prevent static electricity; It may be caused by the fact that the socket of the electric hot water faucet is not grounded, solution:

Replace an outlet with a grounded outlet; It may also be caused by the leakage of other electrical equipment around the faucet, solution: do not place other electrical equipment around the electric hot water faucet. The possible faults of the electric water faucet are:

1. The faucet will make a very harsh sound, and the water will not run smoothly. The possible cause is the sound caused by the phenomenon of water backflow caused by insufficient pressure in the faucet pipe; It could also be the sound of the air inside the water pipe not being discharged cleanly, the air compressing and expanding. 2. The dripping situation of the faucet may be caused by the damage of the gasket inside the faucet, and it can be solved by disassembling the faucet and replacing it with a new gasket.

3. The faucet will not appear in the situation, due to the faucet blockage caused by the water will not come out, this kind of problem, if the faucet is blocked, you only need to disassemble the faucet, and dredge it, if the water pipe is blocked, you need to contact the professional personnel to dredge the pipe to deal with it, it is difficult to clean up the things in the water pipe at home.

Kiss! Hello, happy to answer your <>

The leakage hole on the side of the electric hot water faucet is the pressure relief hole, that is, the pressure in the faucet will pop out when the pressure in the faucet is too high. Just check if the water outlet is blocked, if so, wash it, and have a spare plug next to the pressure relief hole, take it out and plug it in the leaky place.

The faucet has small holes through which water comes out. The causes are different, and the solutions are completely different. Generally, there is still water seeping out after the valve core is closed, which is caused by the loosening of the pressure cap or the deformation of the rubber ring at the bottom of the valve core, if it is the former reason, the pressure cap can be re-installed, and if the latter may need to take out the rubber ring as a whole, it can be solved after reinstallation, I hope mine can help you <>

Do you have any other questions?

In general, don't choose to cut corners when decorating and buy something cheap. If there is a problem in the later use, then you may have to disassemble everything and reinstall it. If you have these costs, it is better to buy a good one to install in the kitchen, and it will last longer.

If you want to boil hot water, you must wait for a while before turning on cold water, so that the faucet will not be damaged. The faucet in the kitchen must be of good quality, so that the quality can be guaranteed.

It may be that the hot and cold valves are not properly installed, or it is possible that the shaft gasket inside the faucet is completely worn and damaged, or it is possible that there is a gap between the faucet bolts and a serious water leak.

It is normal for this type of faucet to experience alternating between cold and hot water at the same time, causing problems with the pipes and frequent leaks.

This is because the parts are damaged, not tightened, used inappropriately, and there is still some water in the pipe, and there is a delay.

The electric hot water faucet leaks when the hot water is turned on as soon as the hail hits! Hello, I am glad to answer for you<> electric hot water faucet leaking electric hot water faucet water pressure switch silicone cap leaking. In general, the trembling handle does not leak when it hits the cold water position, and it leaks when it hits the hot water position.

Solution: Unplug the power supply (there are more electrical parts here, and it is safer to unplug the power supply) Open the side cover to remove the crimping board, see the white ceramic water pressure ejector rod, unscrew the plastic thread gland with a special tool, and take out the silicone cap. Electric faucet leakage: The heating body of the electric hot water faucet is sealed and leaking.

At the wiring of the heating rod, the fuse is composed of 3 O-rings, and the water leakage is caused by the broken O-rings. Solution: Replace the O-ring.

Problems with leaking electric water taps and newly installed faucets. We have several products that leave the factory; The main body is placed separately from the elbow. It is required to be installed well at the time of installation, otherwise there will be water leakage.

Hope mine can help you <>

Do you have any other questions?

It is recommended that you buy another water tank, buy a water pipe, and lead the leaking water to the water tank, and then use it to water flowers and raise fish! But it is recognized that the valve is not strict. There's a red-blue bitter origin on the valve, plastic.

Warp it down and take out the screws with the inner hexagon. It's okay to change your mind. The valve core is about five to fifteen pieces.

Connect the other tube to the tube and install a plugging nut at the outlet of the connected tube. Plug nuts are cheap for 1 dollar. Since I bought a hot and cold water faucet, the hose must be equipped with two.

One hose is connected to the normal use, and the other is also connected to a non-use triangle valve to install, so that the triangle valve can be closed.

After the valve core is closed, the faucet is still out of the water In this case, it may be the reason for the loose pressure cap, moving or the deformation of the rubber ring at the bottom of the valve core, for the former, it is recommended to remove the handle and decorative cover, and re-tighten the pressure cap to be a new product, which can generally be used for two or three years, with good maintenance and longer life. This requires regular dismantling and washing. When the old product leaks, first check the valve core and gasket to see if there are impurities and need to be repaired as appropriate.

First of all, check it and find the location of the water leakage, whether the gasket is broken, or the water seal is not tight enough; Then according to the situation, if the gasket of the faucet is broken, go to the hardware store to see if there is a suitable gasket to buy a replacement can be replaced, this situation is mostly due to the installation was not installed well, did not care at the time or the water seepage was very slow and did not notice, and so on for a long time, especially when the water pressure in the pipe fluctuated, the situation of jogging water began to appear.

There is a plastic gasket inside the faucet, if the faucet is always dripping, it may be that the gasket inside is broken, we need to buy a new gasket, and then replace it with it. There is no leakage from the water spout: this happens when the shaft gasket inside the faucet is worn.

Solution: according to the size of the faucet to choose the corresponding, pliers to unscrew the faucet gland, and use the clamp to take out the worn shaft gasket.

It is because the switch has failed, and the switch can no longer control the water source when it is in use, so there will be water leakage.

It is very likely that some parts of the inside have been destroyed, so there is a water leak, such as a leak from a faucet.

It may be that the faucet is broken, and when the faucet is broken, it will leak.

Summary. The electric hot water faucet leaks as soon as the hot water is turned on: first check whether the silicone cap of the faucet and switch is damaged or slippery, if the silicone cap is damaged, unplug the power supply and replace the silicone cap in time.

If there is still water leakage after replacing the silicone cap, check whether the faucet seal is worn out, and replace the seal if it is worn. There is no problem with the silicone cap of the sealing ring, it may be that the internal pipe body is broken, and you can contact the manufacturer for maintenance.

The electric hot water faucet leaks when the hot water is turned on for the first time: first check whether the silicone cap of the faucet and switch is damaged or slippery, if the silicone cap is damaged, unplug the power supply and replace the silicone cap in time. If there is still water leakage after replacing the silicone cap, check whether the faucet seal is worn out, and replace the seal if it is worn.

There is no problem with the silicone cap of the sealing ring, it may be that the internal pipe body is broken, and the manufacturer can be contacted for repair.

Causes and solutions of electric faucet leakage: 1. Silicone cap problem of faucet: If the electric hot water faucet leaks when putting hot water, it is very likely that there is a problem with the silicone cap.

According to the model of the faucet, choose a silicone pad that fits the size, turn off the power, and replace it. 2. Sealing problem at the heating rod: The heating rod part of the electric water faucet has a sealing ring, and the sealing ring is damaged or worn, which will also cause the faucet to leak.

Once it is found that the sealing of the heating rod is leaking, check and replace the sealing circle in time. 3. Water leakage in the gap at the elbow: the electric hot water faucet can generally move left and right, and in the process of moving, it will inevitably cause a certain amount of extrusion and wear at the elbow, resulting in loose sealing at the elbow, and contact professionals to repair and replace the elbow in time if there is a problem.

4. Faucet quality problems: The internal pipe body of the faucet may be ruptured, and there will be serious problems, so suspend the use and contact the manufacturer for repair or return in time. Do not easily replace the accessories of other factories with electric water faucet accessories, which will affect the original design.