How to deal with funnel water pipe leakage, and what to do if the water pipe is leaking?

I personally think there are three possibilities for funnel water pipe leakage, and the following is a list of solutions for you.

The first possibility,The rain pipe is clogged

Our funnel water pipe is generally used under the eaves to receive rainwater, due to some sundries too much caused by the whole pipe is blocked, the water can not be drained or slowly leads to leakage everywhere.

Workaround:Just use a long wire to plug it out

The second possibility,The funnel hose itself is damaged

Because feng shui is exposed to the sun, especially the sunny side, it is easy to become very brittle when exposed to the sun, so it is very easy to be damaged, and this often happens after a long time.

Workaround:Buy a new funnel water pipe to install on

The third possibility,Leaks in the connectionsWater. As indicated by the arrows in the figure below.

This is also a very common problem, as leakage occurs due to oxidation of the adhesive glue.

Workaround:The first step is to remove the funnel.

In the second step, the surface of the joint is sanded with medium-sized sandpaper to remove the traces of old glue.

In the third step, the adhesive is applied to the joint.

Fourth, install the funnel back.

There are only three types of water leaks that I know, and your problem should be one of them, so judge for yourself how to deal with it.

There is generally only one possibility for the problem of floor drainage and water leakage, mainly because the waterproofing of the joint between the sewer pipe and the floor slab through the floor slab is not done well. Floor drains are generally not a problem. Even if it leaks, the water can only flow into the pipes.

However, it cannot be ruled out that the waterproofing of the entire ground has not been done well. It is good to do a waterproof as a whole.

1. The safest solution is to replace the fittings and pipes at the leaking location. Close the main valve, discharge the water, use PPR scissors to cut off the leaking pipe, use the PPR hot soup machine, and add a section directly. The process is not complicated, and it can be solved in 30 minutes by skilled workers.

2. Wipe the leaky part and buy it with plugging king (waterproof cement). Add a little less water, and if it is very thick, you can paste it under the large surface at the leakage position. Cast iron sewer pipes are also often remedied in this way.

3. Use polyurethane waterproof powder (generally used in the bathroom waterproof) to transfer water and brush it on the leakage.

4. Use weatherproof glue to hit the water leakage.

1. Find the leak point. When a water pipe is leaking, the wall is wet, or where the leak can be seen, the water is from top to bottom, so find the leaking water pipe along the wet marks on the wall.

2. Mark the leaking water pipe. If the water pipe is really in the wall, then you should ask a worker to drill the hole and open the wall, if the water pipe is leaking outside the wall, it is easy to do, see what material the water pipe is made of. Such as plastic, steel, PV and so on.

3. Treat with waterproof tape. This can be bought at hardware stores, first with waterproof tape (also known as waterproof paper) on the outside of the leaky water pipe breaded several layers, then wrapped in foam glue, then wrapped on the outside, then wrapped on the waterproof paper outside the foam glue, and then wrapped on the foam paper outside the waterproof paper.

1. It can be repaired with electric welding (it is also possible to work with water, preferably without water pressure).

2. Find a bicycle inner tube, wrap the leakage point in a few layers, and then tightly wrap it with a thin wire.

3. The steel pipe can be connected with PPR or PE pipe, and there are special joints sold on the market. However, the operation is very troublesome, professional tools are required, the steel pipe needs to be threaded, and the PPR pipe must have a hot fuser.

4. Treat with waterproof tape. You can go to the hardware store and buy this, it's very cheap. Wrap several layers on the outside of the leaking water pipe with waterproof tape (also known as waterproof paper), then wrap another layer on the outside with foam glue, then wrap it on the outside of the foam glue with waterproof paper, and then wrap it with foam glue on the outside of the waterproof paper.

Common leakage of different types of water pipes: 1. Causes of water pipe joint leakage: This situation is generally relatively slight, and it is not difficult to solve it, which is due to the fact that the water pipe and the faucet are not well connected.

2. Causes of sewer pipe leakage: water pipe hardening or long-term foreign body blocking the water pipe resulting in rupture.

3. Causes of plastic water pipe leakage: water pipe hardening or long-term foreign body blocking the water pipe leads to rupture.

Water Pipe Leakage Solution Water Pipe Leakage Solution Water Pipe Fitting Leakage Solution:

The water pipe joint at home is leaking, and the pipe joint itself is broken, so you can only replace it with a new one. If the rubber pad is aged, it will be replaced with a new one, and the wire mouth will be coated with thick white paint and then wrapped with hemp silk and then installed, and it can be wound with raw material tape.

If it is a problem of the faucet, due to the wear of the axial gasket in the faucet, use pliers to loosen the gland and remove it, take out the axial gasket with a clip, and replace it with a new axial gasket.

Solutions for leaking sewer pipes:

If it is a PVC water pipe, you can buy a PVC water pipe to connect it yourself, first cut the broken pipe, put the interface into one end of the pipe first, so that the cutting position of the other end is just flush with the other opening of the interface, so that it can be straightened, and then send it directly to this end, so that both ends have a certain cross distance (length) and then disassemble it, and use PVC glue to apply it to the inside of the two ends and the outside of the two sewer pipes.

You can buy waterproof tape to repair the sewer pipe, just wrap it up, and then use mortar waterproofing agent and cement to wipe it on. If you can't handle it yourself, it's better to find a professional company.

Plastic water pipe leakage solution:

First, use a small hacksaw to see off the leak - the saw edge should be flat, use sandpaper to gently sand the newly exposed port, and do not wipe the port too much with a clean cloth. Apply to the port with special glue and let it dry for a while; At this time, apply glue to the "bamboo" joint, connect the port with the "bamboo", and turn it repeatedly until it is firm. In the same way, apply an appropriate amount of glue to the seam after everything is ok to ensure that there is no leakage.

Extended Materials. PVC Pipe Installation Instructions:

1. Saw pipe and groove.

The length of the sawed pipe is determined layer by layer according to the actual measurement and the size of each connecting pipe fitting. Tools such as fine-toothed saws, cutters and pipe cutters should be used for pipe sawing tools. The fracture should be smooth, and there should be no deformation at the section.

The socket part to be bonded can be filed into a 15o 30o groove with a medium plate file. The length of the groove is generally not less than 3mm, and the thickness of the groove should be 1 3 1 2 of the thickness of the pipe wall. Once the beveling is complete, the debris should be removed.

2. Protection of socket interface.

After the socket interface is connected, the extruded adhesive should be scrubbed clean with cotton yarn or a dry cloth dipped in a little acetone and other detergents. Depending on the performance of the adhesive and climatic conditions, it is static until the interface is cured. The curing time should be appropriately extended during winter construction.

What to do if the sewer pipe is leaking?

In many cases, the basic cause of sewer leakage is due to its own aging and loosening of parts.

1. If it is a PVC water pipe, you can buy a PVC water pipe to connect it yourself, first cut the broken pipe, put the interface into one end of the pipe first, so that the cutting position of the other end is just flush with the other opening of the interface, so that it can just be straightened, and then send it directly to this end, so that both ends have a certain cross connection distance (length) and then disassemble it, and use PVC glue to apply it to the inside of the two ends and the outside of the two sewer pipes.

2. You can buy waterproof tape to repair the sewer pipe, and then wrap it up, it is generally recommended to choose a strong waterproof tape that is resistant to low and high temperatures, and then use mortar waterproofing agent and cement to wipe it on.

3. It's better to find a professional company, if you can't handle it yourself.

What to do if the sewer pipe is leaking?

What to do if a plastic sewer pipe is leaking?

If it is a leak in a plastic water pipe, it is actually very easy to solve. You can buy a plastic water pipe of about the same size and repair it yourself. First cut off the section of the previous sewer pipe leakage, and then connect the joint of the newly bought sewer pipe with the old water pipe joint, or wrap the interface of the new sewer pipe with the interface of the old water pipe, so that the two ends are like a pipe, and then apply a layer of glue on the outer layer of the sewer pipe, wrap it with a watertight cloth bag, and wrap it a few more times, and then the end of the new water pipe connection, according to the previous disassembly method, the in-situ device will be on the line.

What to do if the sewer pipe is leaking?

What should I do if my stainless steel sewer pipe is leaking?

So what if you use a stainless steel hose series of sewer pipes at home? What should I do if the sewer pipe leaks? In fact, this repair solution is not much different from the solution to the leakage of plastic sewer pipes.

According to the advice of professionals, it is to use waterproof tape to repair the leakage of the sewer pipe, in a few circles of tightness, and then use the cement and mortar waterproofing agent, you can, in addition, if it is not convenient to do it, you can find a professional company to repair the leakage of the sewer pipe, it is better.

What should I do if the water pipe in the wall is leaking?

If there is a leak in the water pipe in the wall, you can only chisel the wall to really find the leakage point of the water pipe and repair it thoroughly. In addition, you can also find a property or renovation company to see what the situation is.

What to do if the sewer pipe is leaking?

Precautions for water pipe leakage.

When the water pipe is leaking, you need to turn off the power supply first, and before checking the cause of the water leakage, check whether the power supply is turned off, because water conducts electricity and is prone to danger. Then wrap the leak with a soft object such as a rag to prevent the water from splashing around. Find the valve of the water pipe and tighten it until the water no longer flows.

If you can't handle it yourself, you should find a repairman to repair the water pipes.

Generally, there are many kinds of waterproof tapes on the market, but many people don't know which one is good, according to the test, as long as it is waterproof and sealing, can withstand low and high temperatures, adapts to extreme environments, has strong viscosity, and is light and thin, it can be selected.

What to do if a water pipe is leaking? The tutorial is very detailed and easy to follow.

If the plastic water pipe at home is leaking, the solution will be different depending on the situation! 1. The water leakage point is small; Directly buy the glue for the special water pipe, and then use a special plastic spray gun, plus a plastic welding rod to make up for it. 2. Leakage of sewer pipe; If it is a PVC water pipe, you can buy a PVC water pipe to connect it yourself, first cut the broken pipe, put the interface into one end of the pipe first, so that the cutting position of the other end is just flush with the other opening of the interface, so that it can be straightened, and then send it directly to this end, so that both ends have a certain cross distance (length) and then disassemble it, and use PVC glue to apply it to the inside of the two ends and the outside of the two sewer pipes.

3. The joint is loose; The first thing to see is whether the plastic water pipe joint is broken, or can not be used, if it can be used, it can be tightened directly with equipment tools, if it has been produced cracks or broken, can not be used in the case, then it is best to buy a new installation. If it can be repaired with glue, it can be repaired as much as possible, and it can be repaired with cement, waterproofing agent, waterproof glue and other products.

With rubber is the section sealed. It seems that the cross-section is not flat enough. Try grinding on the wire cross-section. If you don't use the sealing tape to wrap a few times around the wire mouth, it should solve the problem.

If the water pipe is leaking, you can buy a new one and splice it or repair it with waterproof glue. If the water pipe is made of PVC material, when there is a water leak, cut off the leaking part, buy a new water pipe, replace it, and the connection must be firm. For water pipes of other materials, buy waterproof glue in the market, coat it in the leaky water pipe, and then use mortar waterproofing agent and cement to apply it.

1.Find the location of the water leak: The first thing to do is to determine the location of the water leak, which can be judged by looking at whether there are traces of water or water droplets around the water pipe.

2.Turn off the water source: Before repairing the water pipe, the water source must be turned off to prevent the water from continuing to flow out.

3.Clean up the leakage: Clean the leak and remove the surrounding debris for better repairs.

4.Use tape or glue: If the leak is small, you can use tape or glue to repair it.

Apply the tape or glue to the leak and wait for it to dry. 5.Replacement of pipes:

If the leak is severe, the pipe needs to be replaced. You can make Zheng lead bird use a pipe cutter to cut off the leaking part and replace it with a new pipe. 6.

Have a professional fix it: If you can't fix the leak yourself, you can ask a professional to fix it. They will be more professional and effective in solving problems.

If the water pipe is leaking, it is necessary to take measures to repair it in time, and the specific methods are as follows

1.Turn off the water source: First, close the valve at the inlet pipe and cut off the water source.

2.Drain the pipe: Open the faucet, flush tank and other equipment to drain the water in the pipe jujube vertical to reduce the pressure in the pipe.

3.Find the location of the water leakage: use the feel, listen to the sound, observe and other ways to find the location of the water leakage, and find the location of the water leakage by touching whether the pipe has a wet feeling, listening to whether the pipe has a sound, and observing whether the extended pipe has stagnant water.

4.Fix the vulnerability: Use copper pipe fittings, plastic pipe fittings, pipe clamps and other tools to repair water leaks, and pay attention to the selection of repair tools to match the material of the water pipe.

When using the pipe clamp, ensure that the surface of the pipe is dry and clean, and follow the instructions for use when installing.

5.Test the leakage: After repairing the leak, first open the valve to check whether the water source is restored, then check whether the pipeline is leaking, if there is no problem, the repair is considered successful.

If you are not familiar with the repair operation of water pipe leakage, it is recommended that you seek the help of a professional plumber to repair it to avoid unnecessary safety hazards.