How many kilometers does the Prado change the belt when it is corrected

Morning number, if this car is a timing belt, it needs to be replaced before 80,000 kilometers, when the timing belt is aging and damaged, if the timing is misaligned more, it will top the valve, and if the misalignment is less, the engine will work unstable, shaking, and fuel consumption.

Hello, for Toyota Prado, it is recommended that you replace the timing belt every 100,000 kilometers, as long as the number of kilometers does not exceed 100,000, there is generally no problem, this can be replaced regularly.

This is a timing chain, no need to replace, the transmission belt, need to be replaced, generally 100,000 kilometers to replace once, oh, it is best to replace the original effect will be better, about 500 yuan.

Toyota Prado this car is recommended to replace the timing belt for about 100,000 kilometers, for reference.

The timing belt of the Toyota Prado car is recommended to be replaced once in about 100,000 kilometers.

Generally speaking, the timing belt of this motor vehicle is built at about 60,000 kilometers, which can be considered to be replaced, which is relatively reasonable.

Hello, the car timing belt is generally replaced once every 80,000 kilometers, and the tensioner and the peripheral belt are replaced together, I hope it will help you.

Hello, this Toyota Prado generally replaces the timing belt at about 100,000 kilometers, and replaces it with the tensioner.

Hello, if the timing belt is replaced, the Prado car can be replaced for about 80,000 kilometers.

Hello! The Prado vehicle generally travels between 8 and 100,000 kilometers and needs to be replaced with a timing belt.

Hello, this car is generally 8-100,000 kilometers to replace the timing belt once, you can go and check it.

Hello, Prado's car can be replaced normally for 100,000 kilometers, and there is no abnormal situation that does not need to be replaced too early.

Toyota Prado If the timing belt is replaced, it is recommended that it needs to be replaced for 80,000 kilometers.

Hello, Prado recommends driving 80,000 kilometers to replace the official belt, you can refer to the maintenance on time!

Hello! Generally, the formal belt is about 60,000 kilometers in three years. It is necessary to check and replace it, and if there is a crack, it needs to be replaced in time.

Hello, the timing belt of this vehicle is recommended to be replaced every 80,000 km. You can check the instructions for use of the vehicle.

Hello, Toyota Prado, this model is generally about 80,000 kilometers away from replacing the timing belt. For details, please refer to the maintenance manual.

How many kilometers does the Toyota Prado timing belt change? Toyota Prado ( Check price |.)How many kilometers of timing belt to change? The timing belt is generally replaced at 6-8w kilometers, and it is recommended to refer to the vehicle maintenance manual for the number of kilometers of replacement time.

The Toyota Prado uses a timing chain and is maintenance-free. The main function of the engine timing belt is to drive the valve mechanism of the engine to make the engine intake and exhaust valves open or close at the appropriate time, so as to ensure that the engine cylinder can suction and exhaust normally. Here are the steps to replace the timing belt:

1. Disassemble the valve chamber cover, disassemble the crankshaft pulley, and remove the timing chain shell; Rotate the crankshaft, turn the crankshaft to the top dead center of a cylinder, screw the crankshaft fixing screw, and fix the crankshaft; 2. Rotate the intake and exhaust camshaft, there is a groove at the rear end of the camshaft, align the grooves of the two camshafts in a balanced manner, and snap the special tool into it; 3. Dismantle the old chain under the line and replace it with a new one. The crankshaft pulley is also without a slide key, and when installed, there is a round hole on the pulley, which is aligned in the groove above the chain shell; 4. The crankshaft position sensor can be adjusted, and the gap should be adjusted in place during installation, otherwise the fault code will be reported; Both the crankshaft sprocket and the pulley are self-fiddling and rotating. @2019

Prado belts are generally 60,000 kilometers and need to be replaced. A car belt has two, a timing belt and an accessory belt. When the belt is replaced, the tensioner and idler pulley need to be replaced at the same time, because the life of the belt and the tensioner is almost the same.

The engine drives various auxiliary mechanisms through belt drive, such as the compressor of the air conditioner, the power steering oil pump, the alternator, etc., if the belt slips or breaks, the related auxiliary mechanisms will not be able to operate normally, and the normal use of the car will be affected. Therefore, it is necessary to regularly inspect the transmission belt.

There are three types of belts commonly found in automobiles: fan belts, swift ribbed belts, and positive belts. Among them, the timing belt is an important part of the engine valve system, which ensures the accuracy of the intake and exhaust time through the connection with the crankshaft and a certain transmission ratio.

Installation location of automobile belt: In automotive applications, it is mainly installed in the position of automobile engine crankshaft wheel to cam, water pump, generator, air conditioning compressor, steering power pump and other positions. (Photo by photo:.)

Li Linwei) @2019

The replacement method of the Toyota Prado timing belt is as follows:

1. Disassemble the valve chamber cover, disassemble the crankshaft pulley, and remove the timing chain shell; Rotate the crankshaft, turn the crankshaft to the top dead center of a cylinder, screw the crankshaft fixing screw, and fix the crankshaft;

2. Rotate the intake and exhaust camshaft, there is a groove at the rear end of the camshaft, align the grooves of the two camshafts in a balanced manner, and snap the special tool into it;

3. Remove the old chain and replace it with a new one. The crankshaft pulley is also without a slide key, and when installed, there is a round hole on the pulley, which is aligned in the groove above the chain shell;

4. The crankshaft position sensor can be adjusted, and the gap should be adjusted in place during installation, otherwise the fault code will be reported; Both the crankshaft sprocket and the pulley rotate freely.

The Prado timing chain is generally the same as the life of the car, and the answer given by the mechanic of the 4S shop is 18-200,000 kilometers.

However, this is only an approximate replacement range, because some cars have problems above 100,000 points, and some cars can run 25-300,000 kilometers. But to be on the safe side, even if there is no problem with 200,000 km, it is better to replace it in case something goes wrong.

If your car is a timing chain, the timing chain has a long service life and low failure rate compared to the timing belt, and it is not maintenance-free for life. In the process of starting the operation of the lifting and changing machine, there will be wear between the timing chain and the sprocket, and there is also a certain service life.

If the engine lubricating oil is not replaced for a long time or the quality of the oil is not good, it is easy to aggravate the wear and reduce the life of the timing chain.

Maintenance method of timing chain.

For the maintenance of timing chains, we can first look at the working principle of timing chains: timing chains are not directly rubbed against the sprocket, but lubricated with lubricating oil. If there is direct friction, the life of the chain is also short.

Therefore, when our car is maintained, we must ensure that the engine lubricating oil is changed frequently to ensure the quality of the oil, so that the service life of the timing chain can be guaranteed by hail lead.

1.The piston of the first cylinder is held in the top dead center position, and the notch on the outer edge of the crankshaft timing pulley is aligned with the raised "|" on the pulley cavitytags. 2.

Make sure the pulley chamber and transmission pulley are clean and oil-free and water-free, and wipe them with a clean white cloth if necessary. 3.After fixing the timing pulley of the fuel injection pump with a special tool, tighten the nut according to the specified torque.

Assemble the belt transition wheel and tighten the hexagonal flange face positioning bolt connecting the belt transition wheel to the specified 110 10N·m.4.The camshaft timing pulley and the fuel injection pump timing pulley are positioned at the corresponding threaded hole position in the pulley cavity at the same time with M8 process positioning bolts; The pulleys have been marked with assembly markings, and the assembly line assembly has been changed to a marked assembly.

5.In accordance with the requirements of 1 crankshaft timing pulley - 2 camshaft timing pulley - 3 belt transition wheel - 4 fuel injection pump timing pulley, the timing belt assembly is loaded into each transmission pulley in turn, and the marks on the belt should be aligned with the marks on each pulley. The belt timing arrow is in the same direction as the engine (clockwise), the outer edge of the belt is flush with the outer edge of the camshaft (the distance between the outer edge of the belt and the outer edge of the camshaft pulley is 0 mm), and the end face of the belt is in the same plane.

6.Assemble the tensioner assembly on the pulley chamber, and fix the tensioner assembly with hexagonal flange face positioning bolts, but do not tighten it for the time being, so as to ensure that the tensioner assembly can move freely. After assembly, it must be ensured that there is no multi-tooth or wrong tooth phenomenon between the camshaft timing pulley and the fuel injection pump timing pulley, between the crankshaft pulley and the camshaft pulley, and it is absolutely not allowed to bend the timing belt assembly during assembly.

Millions of car purchase subsidies.

Generally speaking, the vehicle should be replaced when it travels to 6-80,000 kilometers, especially in the northern region, it is recommended to be 60,000, preferably not more than 80,000, and in the south, it can be extended to 8-100,000 kilometers. It is recommended to refer to the vehicle maintenance manual for the replacement time and kilometers.

The timing belt is an important part of the engine valve system, which ensures the accuracy of the intake and exhaust times through the connection with the crankshaft and a certain transmission ratio.

The timing belt is very important for the normal operation of the group line engine, once the timing belt is damaged, the valve collapse beam, the ignition work will stop and will not work, and the cylinder head will be damaged in serious cases.

As the working time of the slag hood engine increases, the timing belt and its accessories, such as timing belt tensioners, timing belt tensioners and water pumps, etc., will wear or age, so carefully check whether these accessories are good every time you replace the belt.

When in use, it is necessary to regularly check the use of the timing belt, if you see cracks on the surface of the timing belt, you need to pay attention to whether the timing belt is aging, there is abnormal noise when driving, and you need to pay attention to whether the timing belt is installed correctly. (Photo by Chen Min 2 of Pacific Automobile Network).