-
How to remove dry marks on floor tiles.
1. Water stains are alkaline mixtures, because acid and alkali can be neutralized, so dry traces of water stains can be removed with an acidic solution. The more common acidic solutions are edible vinegar and oxalic acid.
Hydrochloric acid, phosphoric acid, etc., any kind of acidic solution is fine, mix it with water and acidic solution, and then wipe it with a damp rag.
2. When wiping dry water stains with acidic mixture, use a clean rag, otherwise it will only get dirtier and dirtier. In addition, the acidic solutions mentioned above are corrosive except for vinegar, so wear gloves when doing cleaning work.
3. There are many cleaners on the market that specialize in removing water stains on ceramic tiles, you can follow the instructions on the manual, pour the cleaner directly on the water stains, let it stand for three minutes, then brush it with a brush, and then wipe it dry with a rag.
4. You can add a certain amount of ammonia with soapy water.
Add a few more drops of turpentine.
Mix and stir well, then pour the mixture on the water stain, let it stand for about five minutes, and then wipe it with a clean wet back, and the dry stain may be wiped clean.
5. If the surface of the tile is scratched by sharp objects, it will leave scratches, so you can apply toothpaste to the scratches, and then wipe it with a clean rag to restore the tiles to their original state. This method is suitable for not shallow scratches, but not for deep scratches.
6. The gap of the tile is a place where it is easier to hide dirt and dirt, and it should be cleaned regularly, which can be cleaned with detergent, and then brush a layer of waterproof agent on the gap, which can prevent the water in the gap from causing mildew and bacteria.
-
The house is full of dew, and the ceramic floors are full of water, and now the water is dry. There are traces of water on the ground, if it has seeped into the inside of the ceramic. This cannot be removed, if it is the surface of the table, then it can be gently wiped with a rag.
-
The house used to leak, the ceramic floor was full of water, but now it is dry, and there are scale and water marks on the ground, how to remove it? If there are limescale and water marks on the ground, then you should find a way to buy a special cleaner that removes limescale and water marks, so that this can be wiped off with a pot rubbing ball.
-
-50 degrees water + salt, many people will ignore the water temperature when mopping the floor, thinking that it is okay to use cold water, but this is not the case. The most suitable temperature for mopping water is 40-50 degrees Celsius, with 1-2 tablespoons of salt in it. Salt melts faster in warm water, and mopping the floor with salt water can not only disinfect and sterilize, but also make the floor shiny.
50 degree water + rice water, many housewives know that there are many uses for rice water, you can wash your hands and water your flowers. However, few people know that wiping the floor with rice water will also have a good effect, such as there will be no water stains after the ground is dry, and it is not easy to dust when wiping the floor with rice water. If you want to wipe the floor once in two days, try using rice water, and you will not be disappointed.
50 degree water + laundry detergent, it should be noted that the amount of laundry detergent must not be put too much, if you put too much, there will be a lot of foam, so even if you wipe the floor several times, there will still be water stains when it dries. Just add 1-2 drops to warm water, and there are two points to note, one is that the laundry detergent must be completely melted, and the other is that the mop needs to be soaked in warm water for a few minutes, so that the mop can completely absorb the laundry detergent!
-
The stains on the floor are not easy to remove, teach you a simple trick, no matter how dirty the floor is, you can mop it clean.
-
Wood floor cleaning work is divided into three categories:
One. It is harmful to the wooden floor (including strong corrosion, water immersion, hard friction, etc.).
Two. Medium damage (e.g. wet wipe, soft rubbing) three.
The damage is small, or there is no harm (dust adsorption, maintenance + cleaning) Therefore, in order to better protect from damage, the third type of method should be used as much as possible when cleaning the wooden floor
1. Wipes with dust adsorption function can be used for dry wiping;
2. You can use a vacuum cleaner to remove dust;
3. If there are stains on the wooden floor, you can use a natural dissolving agent with dissolving effect --- orange oil to dissolve the dirt, and then wipe and use a natural active agent that separates the dirt from the floor to --- soap corner, and after activation, wipe off the dirt or use a soft abrasive with a cleaning and destaining effect to wipe and remove the dirt; In short, try not to use a lot of water for wood floor cleaning.
-
Floor tiles are commonly used to decontaminate them.
1. Daily cleaning of ceramic tiles can be cleaned with dish soap, soap, etc.
2. Use soap and a little ammonia and turpentine to clean the tiles to make the tiles more shiny.
3. The polished tile should be waxed regularly, and the time interval should be 2-3 months.
4. If there are scratches on the brick surface, you can apply toothpaste to the scratches, and wipe them with a dry cloth to repair them.
5. The gaps between bricks and bricks can be removed from time to time with detergent, and then a layer of waterproof agent can be brushed on the gaps to prevent the growth of mold.
6. Sodium hydroxide or potassium bicarbonate solution is used for pollutants such as tea, coffee, beer, ice cream, and oil.
7. Ink, cement and other pollutants use dilute solutions such as hydrochloric acid and nitric acid.
8. Use special cleaners for paints, coatings and other pollutants.
9. The marks left by the burning of match stems and paper can be dipped in a small amount of diluted oxalic acid solution with a waste toothbrush.
-
Acidic solution method: an appropriate amount of acidic solution and water matching, mix and match, dip it with a brush, brush back and forth, brush it several times, and then clean it with water. Professional Cleaner:
Pour an appropriate amount of detergent onto a rag to wipe it and rinse it off with water. Soap: Add a section of soap, as well as ammonia and turpentine, and wipe the mixed liquid in the place where it is sprayed to scale.
1. Acidic solution method: an appropriate amount of acidic solution and water matching, mix and match, dip it with a brush, brush it back and forth, brush it several times, and then clean it with water.
2. Professional detergent: pour an appropriate amount of detergent on the rag to wipe it and wash it with water.
3. Soap: Add the soap to a section, mix it with ammonia and turpentine, and wipe the mixed liquid in the place where it is sprayed to the scale.
4. Vinegar + baking soda: Pour an appropriate amount of white vinegar and baking soda into the water, brush the floor with a brush, and then wash it with water.
-
1. Water ingress in a small area of the floor.
When the floor is flooded, the first thing to do is, of course, to dry the water, first wipe the moisture on the surface of the floor with a dry cloth, and then you can choose a practical vacuum cleaner to suck up the water vapor in the splicing gap of the soaked floor or use the cold air stall of the hair dryer to dry; Next, you can use some heavy objects to press on the small area of the warped area, and after a while, the wooden floor will return to normal on its own. If, after a period of time, the joints have to bulge, but they are too far from the original shape of the previous floor, you can try waxing the floor, and the soaked floor after waxing will basically be almost the same as the original. If the color and shape of the floor are still very different from the original state after waxing, then only a partial replacement of the floor is required.
2. The water ingress of the floor is serious.
If there is a large area of soaking water, then we can not deal with it so simply, we should carefully pry up the floor, according to the "well" shape superimposed in the ventilation place to dry, with its stacked weight to prevent the occurrence of deformation, in general, for the quality of the solid wood floor can be used again.
3. Laminate flooring soaking in water.
Whether it is a large area of water or a small area of water, it is not recommended to pry up the laminate floor to dry, which is easy to cause damage to the laminate flooring, and is likely to cause serious consequences that cannot be used again. It is best to drain the surface water of the floor quickly, and then remove the baseboard of the floor, expose the expansion joint, and dissipate the water vapor by the expansion joint, but according to the size of the water intake, it usually takes about seven to fifteen days to dry.
4. Add keel, a small area of water-soaked solid wood flooring.
If a small area of water ingress is found in time, the ground can be cleaned, the board can be pried up, and the wet floor can be dried and reinstalled; If the water inflow is slightly large, not only should the board at the leakage be pried up, but also the opposite board should be pried up along the direction of the keel arrangement, so that the internal air circulation can take away the moisture. If you can't determine the size of the incoming water, it is best to pry up the board in turn according to the flow direction of the inlet water to check the humidity situation to be foolproof.
5. Prevent water ingress into the floor.
After all, rescue after the fact is passive, and taking precautions is the best choice. Usually, pay more attention to the window not to open wide to prevent rain; Always check the air conditioner, plumbing pipes, and washing machine for water leaks. At present, the floor wax mainly plays the role of cleaning and maintenance, and cannot be completely waterproof, so it is very necessary to do early prevention.
-
You can use a mop to mop it clean.
-
Floor drains are the most frequently used facilities in our homes, and with the increase of use, floor drains tend to appear scale. The existence of scale will lead to poor water flow of floor drains, and even make floor drains blocked, which will bring certain troubles to our lives. So, what should I do if there is limescale in the floor drain?
Below, I will introduce the solution from the following three aspects.
1. Chemical detergent cleaning method.
Chemical cleaners can help us quickly and thoroughly clean limescale from floor drains. Here's how to use it: First, find an empty container, then mix the chemical cleaner with water in proportion, then spray it on the floor drain with a mop or sprayer, wait for a while, use a cleaning brush to brush the floor drain, and finally rinse it with clean water.
2. Homemade detergent cleaning method.
The advantage of homemade cleaners is that they are environmentally friendly, non-toxic, and harmless even if they are sprinkled on people. It's as simple as mixing baking soda, vinegar, lemon or alcohol in proportion. The specific use method is similar to chemical cleaners, but it should be noted that the water should be changed frequently, and the water should be thoroughly rinsed with water after washing to avoid health problems caused by detergent residues.
3. Manual cleaning method.
If you're not comfortable with cleaners, or don't like using chemical cleaners and homemade cleaners, you can opt for manual cleaning. This method is relatively simple, you only need to remove the parts of the floor drain and scrub it repeatedly with a cleaning brush and clean water. This method requires more time and effort, but avoids the worries that come with using detergents.
In short, the problem of scale in the floor drain is a problem that we often see in our daily life at home, but as long as we master the correct cleaning method, we can quickly arrange and solve it. Whichever cleaning method you choose, you need to be safe and environmentally friendly.
-
The dew on the floor is due to the high humidity in the room, which causes water vapor to condense on the ground, which brings certain damage to the floor and needs to be dealt with in time. Let's take a look at some common ways to deal with it.
1. Place the dehumidifier. The dehumidifier can effectively absorb indoor humidity, thereby reducing the probability of dew on the floor. At the same time, the windows can be opened for ventilation to accelerate air circulation and take away excess moisture.
2. Use underfloor heating. The use of underfloor heating can keep the ground warm, reduce the probability of water vapor condensing on the ground, and increase indoor comfort.
3. Keep the indoor ventilation state. Open windows regularly for ventilation to increase the circulation of indoor air and avoid condensation of water vapor on the ground after excessive indoor humidity.
4. Keep the ground dry. In the wet season, dry blankets and other items can be laid on the ground to avoid dew on the ground, and at the same time, the ground can be cleaned at any time to keep it dry.
5. Clean in time. Regular ground maintenance is carried out to clean the water stains on the ground to avoid water stains polluting the ground, and at the same time, it can clean up the stagnant water and ensure that the ground is dry.
The dew on the ground is a very troublesome thing and needs to be dealt with in time. It can be treated by adding medium to strong ventilation, reducing indoor humidity, and keeping it dry to ensure the normal use of the ground.
-
Water stains on the floor drain in the bathroom are a very common problem. This problem not only affects the overall hygiene environment of the restroom, but can also cause odors and even serious damage to the floor.
To deal with this problem, it is necessary to take different measures in a timely manner according to different situations. In general, the following points need to be noted:
1.Qing's erection bathroom floor drain.
First of all, the floor drain in the bathroom needs to be cleaned. You can use some effective cleaning agents such as toilet cleaners or bleach to thoroughly clean the floor drain and the surrounding area. This can effectively remove water stains and other debris and ensure the smooth flow of the floor drain.
2.Repair leaks in a timely manner.
If the water stain on the floor drain is caused by a water leak, the leak needs to be repaired in time to avoid greater damage. If you don't have relevant experience, it's best to ask a professional maintenance worker to deal with it.
3.Pay attention to hygiene.
In order to avoid water stains on the floor drain, it is necessary to pay attention to hygiene habits. Washing the bathroom frequently, not throwing a lot of hair or other hard-to-break substances into the sink, not littering the bathroom, etc., can help reduce the appearance of water stains on floor drains.
4.Maintenance and cleaning during the period of the fixed mu nuclear plexus.
In addition to the usual hygiene habits, regular maintenance and cleaning are required. Regular inspection and maintenance can detect water leakage in time and deal with it in time, and regular cleaning can effectively avoid water stains and odors. It's a good idea to clean your bathroom regularly once a month to keep your bathroom tidy and hygienic.
In short, for the water stains on the floor drain in the bathroom, it is necessary to take corresponding measures in time. Only by maintaining hygiene habits, regular maintenance and cleaning, timely repair of water leakage and a series of measures are used reasonably, can the floor drain in the bathroom be kept clean and smooth, and the environment of the toilet more healthy and comfortable.
First of all, you buy the developer's house, the property and the developer are two different things, the warranty period for the installation and use of the water pipe should be 2 years, I estimate that the developer is unwilling to bear, the property is even more unlikely to bear, your own water pipe is already in your own exclusive area, should be borne by the owner. If you can prove that the water pipe is the problem of the original construction, of course, you can ask the developer for compensation, but I guess it is difficult because your home inspection records are signed. If you want to view the original pipeline design drawing, this should be claimable and your right. >>>More
Some netizens mentioned the inconspicuous gasket, but he summarized the quality problem, which is actually a design problem, because the gasket itself is very wear-resistant of nylon, but the contact surface with the copper core is very frizzy and naturally not wear-resistant. >>>More
Before repairing the toilet leakage, it is necessary to determine the cause of the toilet leakage, and the two methods for judging the causes of water leakage are as follows: >>>More
First, the on-site situation:
1) The floor is hollow, and the effect of arching up obviously when walking; >>>More
Water leakage will lead to deformation of the wooden floor, if the water leaks, if it is a small area of water leakage, first clean up the stagnant water, if it is a large area of water leakage, you need to tell the master who installed the floor tiles, do after-sales treatment, and then clean up the water and remove the floor tiles and put them in a ventilated place to dry, in order to prevent the deformation of the floor tiles, the new house must be done rigid waterproof before decoration, especially the bathroom and kitchen, the sewer pipe can not be changed, and the construction waste in the room should also be cleaned up.