What s the deal with a dripping sound in the toilet drain?

A common way to deal with toilet dripping sound repairs.

Toilet drip sound repair.

Toilet drip repair - the cause of toilet drip sound.

1. Inferior material: some manufacturers blindly reduce production costs.

The selection of inferior materials causes the water inlet valve outlet and the water inlet pipe itself to crack during injection molding, resulting in sealing failure, the toilet produces a dripping sound, and the water in the water tank flows into the toilet through the overflow pipe of the drain valve.

Causing a "long flowing water".

2. The inlet valve cannot be closed. When the water submerges the float (or floating bucket), the inlet valve still cannot be closed, so that the water continues to flow into the water tank, and finally flows into the toilet from the overflow pipe to cause water leakage. This phenomenon is especially noticeable when the tap water pressure is high.

3. Improper design: the mechanism of the water tank accessories will interfere during operation, resulting in water leakage. For example, when the water tank is discharged, the float and the float rod will affect the normal reset of the flap and cause water leakage.

There are also float rods that are too long and floats that are too large, causing friction between them and the walls of the water tank, affecting the dripping sound of the toilet, resulting in seal failure and water leakage.

Toilet drip sound repair - the method of toilet drip sound repair.

1. Check whether the flush switch is reset. The plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored. Generally, the switch can be reset by repeating it several times.

Check whether the rubber gasket of the drain port under the ball valve is aged and the seal is not tight, and the problem needs to be replaced. The sound of the toilet dripping can be dealt with.

2. Check whether the connection between the spherical float of the water tank and the water inlet switch is loose. The float is in place and the switch is not turned off, resulting in the water inlet does not stop, and the water flows out from the upright drain pipe after the water is full, as long as the connection between the float and the water valve switch is tightened. If the rubber ball valve is damaged, the seal is not tight, there is a water leakage, and the toilet bowl dripping sound is produced, and it needs to be replaced immediately.

3. Check the rubber plug at the outlet of the water tank. Water tank leakage, basically a problem with the drain valve, check the situation of the rubber plug at the outlet of the water tank, if the rubber plug at the outlet is damaged or blocked by foreign objects, resulting in the rubber plug is not tightly sealed, it will also cause the toilet drip sound. If the water supply pipe in the tank is not placed correctly, it will also affect it to a greater or lesser extent.

This is the sound of leakage caused by the loose closure of the valve controlling the water in the toilet, which will lose a lot of water for no reason, resulting in waste, and it is enough to repair or replace the valve. The valve in this toilet is not expensive, it is available in hardware stores, and the installation is very simple.

Toilet leakage, remove the toilet lid and adjust the toilet water level,

This may be due to the dripping sound of some water flowing from the tank to the inside of the toilet when the water is filled with water in the toilet tank, but when the water becomes more and the pressure makes the tank water sealed, it will not make a sound. If there is still a sound, you can lower the blue float on the left side of the toilet, or you can press the two hemispherical buttons back and forth to reset.

What are the precautions for installing toilet sewers?

1. It can pass through the roof, which can avoid man-made damage, and can also make the later inspection more convenient, pay attention to the hot and cold pipe interface must be in the same plane as the outlet, the normal water pipe is hot on the left and cold on the right, do not bend the pipe when designing, so that it can be far away from the circuit, to ensure that each valve is flat when installed, so that the later maintenance and application will be more convenient.

2. When laying the hot water pipe, it must be separated from the outlet, the water inlet needs to be connected with the main valve, and the water outlet should be connected to the toilet pipe, and the valve needs to be opened after installation to ensure that there will be no water leakage.

3. Because the bathroom will be in contact with water vapor for a long time, it is necessary to do a good job of ventilation, it is best to design windows inside, if the conditions do not allow, in order to avoid the problem of mold and dampness, you need to set up an exhaust fan inside.

4. The sewer pipe of the normal bathroom still has to go to the dark pipe, the water is flowing towards the low-lying place, if it is laid from the ground, it is difficult to find the leakage problem, only when the leakage is more serious, it can be found, so if you go from the top floor, even if there is a water leakage problem, it can be repaired as soon as possible.

1. The water drops in the submersible bend of the sewer pipe, because the submersible bend is filled with water, so that the water pipe itself may be a little leaky when it is pedaling, so that the water becomes dripping when it flows down.

2. Consider wrapping thick dots with soundproof cotton or other soundproof soft objects. It can reduce the impact of points and completely eliminate non-diversion and blocking.

The house I rent now is like this, the upstairs sewer pipe is on the top of my bathroom, the reason for this drop of water is that the water drops in the submersible bend of the sewer pipe, because the submersible bend is stored with water, so that the water pipe itself may be pedaling the toilet is a little leaky, so that when the water flows down, it becomes dripping, and it is really noisy. It is noisy during the day, and at night it is louder and annoying. I also reacted to the resident upstairs, who said it was leaking, but the landlord didn't care.

Because if you change it, it will cost money. The landlord saw that the leak was either large or dripping. The landlord didn't care, and the noise annoyed me and the tenants upstairs.

I heard the loudest. You can go upstairs and report the situation.

Replace the original sewer pipe with a spiral pipe (with spiral corrugations on the inner wall).

Welcome to choose the noise reduction solution of Zhongcai Home Decoration Integrated System, the noise of the partition drainage is a big problem that plagues home life, we have a noise reduction solution. It can be covered with a silencing device, and it is also solved by using a spiral silencing tube by nature.

The sound of dripping water is due to the fact that the drainage on the side of the trap is not very smooth, and the water inside is uneven and has been flowing.

Kiss, <>

I'm glad to answer for you Oh, there is a sound of ticking water in the bathroom sewer pipe: this may be a dripping sound that occurs when the toilet tank is filled with water that does not reach the pressure standard, and part of the water flows from the tank to the inside of the toilet, but when the water becomes more and the pressure makes the water tank water sealed, it will not make a sound. If there is still a sound, you can lower the blue float on the left side of the toilet, or you can press the two hemispherical buttons back and forth to reset the expansion data 1, the drainage pipe of the upstairs home is not common sense (the place that should be low is not low).

2. There are debris in the drainage pipes of the upstairs house that affect the normal drainage. For both of these reasons, there will be a dripping sound, but it will not last too long. 3. If there is a dripping sound all the time, but the cause of the leakage can not be found, it should be the reason for the toilet, and the sealing gasket of the toilet tank is not tight, I hope I can help you!

Summary. 1. What is the reason why the sewer keeps rumbling 1. The sewer pipe keeps bubbling with the sound of running water, which is actually a normal phenomenon, because the sewer pipe will run from the top floor to the bathroom of every household on the ground floor, so when other people's households use water, the sewer pipe of their own home will also make a sound of rushing water. Second, how to solve the sound of running water in the toilet sewer pipe 1, the sound of the sewer pipe is a normal phenomenon, do not need to disassemble the interior for maintenance, if there is no way to accept this noise, we can use the sound insulation method to insulate the sound of the water.

2. We can buy some soundproof cotton and wrap all the water pipes with soundproof cotton, so that there will be no sound of water pipes rushing water. 2. You don't have to panic too much when you hear this voice, it's not that there is a malfunction, but a normal phenomenon.

Why is there a dripping sound in the sewer pipe.

1. What is the reason why the sewer keeps rumbling 1. The sewer pipe keeps bubbling with the sound of running water, which is actually a normal phenomenon, because the sewer pipe will run from the top floor to the bathroom of every household on the ground floor, so when other people's households use water, the sewer pipe of their own home will also make a sound of rushing water. Second, how to solve the sound of running water in the toilet sewer pipe 1, the sound of the sewer pipe is a normal phenomenon, do not need to disassemble the interior for maintenance, if there is no way to accept this noise, we can use the sound insulation method to insulate the sound of the water. 2. We can buy some soundproof cotton and wrap all the water pipes with soundproof cotton, so that there will be no sound of water pipes rushing water.

2. You don't have to panic too much when you hear this voice, it's not that there is a malfunction, but a normal phenomenon.

3. How to prevent the sewer pipe from being clogged 1. When we usually wash vegetables or wash our hair, try to put a funnel in the pool, which can help us filter solid debris and hair, and the debris and hair are not left in the sewer, and basically the sewer will not be blocked. 2. When choosing a sewer pipe, you should choose a slightly thicker, smoother, so that there will be no adhesive stuck to the sewer pipe.

Summary. Hello. This is still a problem with the flush valve of the water tank that has not been repaired (a leaky toilet is generally a problem with the flush valve)!

The flush valve is not closed and dripping, because the water level of the water tank is not visible to a certain extent, and the float valve will be replenished in time (you should hear the sound of water entering after observing for a while), and the dripping water must flow into the toilet (because the water in the tank has only one outlet to enter the toilet)!Because there's so little water, it's not easy for you not to see it! I don't know what structure your drain valve is?

You should be able to fix it yourself! If it is the kind of flap type, it is easier to change without dismantling the water tank, if it is the kind of press, it is more troublesome, and the water tank can be changed first.

There is a dripping sound in the toilet drain.

Hello. This is still a problem with the flush valve of the water tank that has not been repaired (a leaky toilet is generally a problem with the flush valve)!The flush valve is not closed and dripping, because the water level of the water tank is not visible to a certain extent, and the float valve will be replenished in time (you should hear the sound of water entering after observing for a while), and the dripping water must flow into the toilet (because the water in the tank has only one outlet to enter the toilet)!

Because there's so little water, it's not easy for you not to see it! I don't know what structure your drain valve is? You should be able to fix it yourself!

If it is the kind of flap type, it is easier to change without dismantling the water tank, if it is the kind of press, it is more troublesome, and the water tank can be changed first.

If you can be sure that it is the sound of the toilet draining, then don't worry, the accessories in the water tank are not closed tightly after flushing, which is often referred to as constant running water. Since there is no leakage, it proves that the water is flowing normally from the sewer pipe and has no effect on your home.

Toilet dripping sounds can have several causes, including a problem inside the tank or a malfunctioning valve. Here are some possible solutions for Chunhui:1

Check the water level in the tank: Make sure the water level in the tank is not too high, as too high a water level may cause water to flow into the overflow pipe, causing a dripping sound. If the water level is too high, you can adjust the float inside the tank or the water level regulator to lower the water level.

2.Check the seals inside the tank: Check whether the seals inside the tank are damaged or deteriorated.

If a problem is found with the seal, it can be replaced with a new one. 3.Check the tank valve:

If the valve in the tank fails, it can also cause a dripping sound. Check the valve for loose or damaged valves, and replace them with new ones if needed. 4.

Check the parts inside the tank: Other parts inside the tank, such as water level regulators, floats, etc., can also malfunction, resulting in the generation of dripping sounds. Check the functioning of these components and repair or replace them if necessary.

5.If none of the above methods can solve the problem, it is recommended to contact a professional toilet repair service personnel for overhaul and repair. They have the professional knowledge and tools to help solve the problem of dripping sounds.