-
We need to cut off the electricity, clean the outside of the water dispenser, prepare a clean rag, and then prepare white vinegar and disinfectant to dry the entire outside of the water dispenser. There is a locker underneath, take it out and wipe it one by one. Wash the outside first, then the inside.
Drain all the water in the water dispenser, take out the water storage tank inside, take out the parts inside the water dispenser, soak it in a solution containing white vinegar and disinfectant, soak it for a while, and then scrub it with a brush.
After cleaning, put it under the faucet and rinse it several times, and the internal and external parts can be cleaned, and when it is dry, there is no water and put it back one by one, so that the water dispenser will be very clean. There are many types of water dispensers on the market. If it is divided according to the appearance, one is a tabletop, and the other is vertical, which can be placed directly on the table, which belongs to a small water dispenser.
The other is placed directly on the ground, which is large in size and takes up a lot of space. The vertical type is more expensive than the desktop type, and you can choose according to your needs. Depending on the temperature, there are warm and hot and cold types.
If it is warm, the hot and cold type has two taps, one for cold water and one for hot water. When using a cup to hold water, it is easy to touch the back wall and the lower part of the water dispenser switch, and cannot be wiped with a rag. After turning off the refrigeration switch, it takes 3 minutes to turn on the refrigeration, otherwise the compressor will be damaged.
According to the water source, some are bottled water dispensers, some are tap water, and the water dispensers are different, drain all the water in the water dispenser, then remove the smart seat on the water dispenser, and then pour the pure water into the water storage tank, clean the water storage tank, and then turn on the faucet to drain all the dirty water. Prepare a bottle of beer, pour it into the water dispenser's tank, wait for an hour and a half or so, then slowly release the beer, then carefully wipe the tank with a clean cloth and rinse it with water two or three times. Then pour the white vinegar into the water tank of the water dispenser, plug it into the water dispenser again, turn on the water dispenser power switch, release all the white vinegar, and rinse it with water once or twice.
Turn on the red and green drain faucets until the sanitizer is complete. Then rinse several times with boiling or purified water; Complete disinfection and sterilization procedures. Dip cotton with alcohol and gently scrub the back wall and bottom of the faucet.
When heating, be sure to turn on the water pump switch, stop heating, install a water purifier, and prohibit single-cylinder heating when making hot drinks. Place the sealing ring.
Put it on the cylinder body of the hot and cold water dispenser, and pay attention to the adjustment of the sealing performance. Place the cylinder vertically on the base of the hot and cold water dispenser, and the seal must be firmly snapped into the groove to pour the prepared beverage into the beverage keg. Spray hot and cold water dispensers are generally suitable for making fruit juice drinks, while stirring hot and cold water dispensers are generally suitable for making pulp drinks; If the specific gravity of the drink is slightly heavier, you can choose a vortex hot and cold water dispenser.
-
The disassembly method of the direct drinking machine is to first remove the bucket on the direct drinking machine, then remove the tray, and finally use a screwdriver to unscrew the screws, so that the direct drinking machine is disassembled. Ordinary people can also disassemble it at will, because it will not affect the body.
-
The correct disassembly method of the direct drinking machine is: close the water inlet ball valve on the tee, open the water purification faucet, empty the rainwater in the machine, then hold the main filter element, rotate it horizontally about 90 degrees, take out the filter element downward, open the heart filter element packaging, take off the filter, vertically align the cover with the head and insert it upward, and then turn it horizontally about 90 degrees, fasten it, and finally open the water inlet ball valve. At the same time, it can also prolong life. It can be disassembled by ordinary people.
-
The direct drinking machine directly closes the water inlet ball valve on the tee, and opens the water purification faucet to empty the excess water in the machine; Then take out the main filter element in your hand; Ordinary people can disassemble according to the correct disassembly method.
-
The correct way to dismantle is to remove the chassis above, and then disconnect all the wires.
-
The disassembly of the water dispenser is generally carried out because of the need to replace the water pipe or clean and maintain, so let's introduce the disassembly method of the water dispenser.
1.First of all, disconnect the water dispenser from the water dispenser from the water hose to avoid dangers such as electric shock.
2.Make sure that there is no more water flowing out of the water dispenser after leaving the water dispenser, and then remove the water pipe from the water dispenser, this process requires the use of a wrench or a hose knife and other squeezing equipment.
3.Removing the water dispenser from a cupboard or placed counter while paying attention to the weight of the water dispenser may require the combined efforts of multiple people.
4.Disassembling the casing of the water dispenser requires the use of tools such as screwdrivers, which need to be handled carefully so as not to damage the internal structure of the water dispenser.
5.Identify the parts that need to be replaced or cleaned, and replace or clean them according to the instruction manual of the water dispenser.
6.After replacing or cleaning, reinstall the water dispenser housing and put the water dispenser back in place to reconnect the water pipes.
7.Finally, make sure that the water dispenser is firmly connected to the water pipe again, connect the power cord again, turn on the power supply of the water dispenser, and test.
In general, the disassembly method of the undercounter water dispenser is relatively simple, and you only need to follow the steps one by one. However, due to the large number of water dispenser components, care needs to be taken when disassembling them to avoid damaging critical components. It is best to have professional guidance or assistance to ensure that the disassembly process is safe and reliable.
-
Water dispensers are an essential device in our lives, but after a long period of use, they may need to be cleaned and maintained. The dismantling of the water dispenser is the first step in cleaning and maintenance. Here's how to disassemble the water dispenser::
1.First turn off the power and water inlet pipe of the water dispenser, take down the bucket of the water dispenser, and wrap the water pipe and power cord with a towel to prevent water leakage or electric shock.
2.Place the body of the water dispenser on a stable ground, loosen the "hot and cold water" switch, unplug the water pipe, and then use a screwdriver to remove the screws on the bottom of the body.
3.Gently pick up the body of the water dispenser, unplug the water pipe at the top of the mega mill body with needle-nose pliers, and then place the body on the workbench.
4.Use a screwdriver to remove the screws on the back of the fuselage, remove the back cover, and then use needle-nose pliers to remove the two water valve pullers on the top of the fuselage.
5.Separate the individual parts and clean them thoroughly with a brush and detergent, replace the parts that have deteriorated, and repair or replace them.
6.Once the disassembly is complete, follow the reverse steps for assembly.
It should be noted that before disassembling the water dispenser, it is important to make sure that you have understood the mechanism and working principle of the water dispenser, and take the correct safety measures to avoid causing injury to yourself. If you encounter a problem that you don't understand, it's best to ask a professional to repair and clean it.
The correct disassembly method is to cut off the power first, and then remove the outer iron shell by screwing, and then break the wires inside, and then take out the entire compartment, and then take out the motor to finish.
For the disinfection cabinet that you want to move at home, the correct disassembly method should be to turn off the power first, and then open the cabinet, you can see that there are screws on both sides of the cabinet. >>>More
Can a drum washing machine wash down jackets, this is the correct way to clean, try it after reading.
Partition scrubbing: The whole mouth teeth can be divided into two parts: maxillary teeth and mandibular teeth, the upper and lower parts are divided into left and right sides, and each side is subdivided into three areas: anterior, middle and posterior. Each cell consists of only 2 to 3 teeth, which is used as a unit for brushing the teeth, requiring one cell to be cleaned before another cell is brushed. >>>More
The first thing to look at is whether it is a screw or a card. >>>More