Does the Ward harvester need to adjust the soybean sieve

Can be adjusted. When harvesting soybeans, the speed of the Ryzen engine should be adjusted according to the crushing of soybeans, and the engine speed should generally be 1500-2200 rpm. However, it should be noted that if the soybean is crushed more, the corresponding reduction of the engine speed can reduce the speed of the threshing drum and reduce the crushing of soybeans, and the air volume of the fan can be adjusted to the maximum, so that the harvested soybeans are relatively clean.

*When the World harvester harvests soybeans, the sieve can be adjusted**. Generally speaking, the adjustment of the sieve includes the adjustment of the gong rod and the adjustment of the sieve blade.

Adjustment of the gong rod: When all the materials in the threshing drum are sent, the vibrating screen handle is offset to the right side until the gong rod is adjusted to a row that does not touch the left and right sieve pieces, and then adjust the position of the front and rear gong rods to align the upper and lower ends of the front and rear gong rods, and then adjust the left and right gong rods to align the upper and lower ends of the left gong rod and the upper and lower ends of the right gong rod.

Adjustment of the sieve sheet: first of all, after all the materials of the threshing drum are sent, the vibrating screen is offset to the right side, and then the upper sieve is adjusted to the front 1 3 arc is slightly smaller, and the rear 2 3 arc is slightly larger. The first 1 2 arcs of the lower sieve are slightly smaller, and the rear 1 2 radians are slightly larger.

It should be noted that the adjustment should be carried out after removing the safety screws to avoid accidents. The above suggestions are for reference only, if you need more detailed information, it is recommended to contact the after-sales service personnel of World harvester to get it.

Summary. 1. Master the appropriate harvester driving speed and feeding amount. Agricultural mechanics mainly consider straw and yield.

2. Master the rotation speed of the reel wheel, the speed is too low, the harvesting is difficult, and the threshing and other problems are too high. 3. Adjust the appropriate threshing gap. The minimum gap is not less than 4mm, and the upper sieve should be adjusted according to the maturity of the crop.

The upper sieve is 2 3 as the standard, and the lower sieve has also been 2 3 as the standard. 1. Master the appropriate harvester driving speed and feeding amount. Agricultural mechanics mainly consider straw and yield.

2. Master the rotation speed of the reel wheel, the speed is too low, the harvesting is difficult, and the threshing and other problems are too high. 3. Adjust the appropriate threshing gap. The minimum gap is not less than 4mm, and the upper sieve should be adjusted according to the maturity of the crop.

The upper sieve is 2 3 as the standard, and the lower sieve has also been 2 3 as the standard. If the stripping is not clean, the gap of the pressure feeding roller should be adjusted, and then there is the gap between the upper and lower and left and right sides of the peeling roller.

1. Master the appropriate harvester driving speed and feeding amount. Agricultural mechanics mainly consider straw and yield, and ask questions and questions. 2. Master the rotation speed of the reel wheel, the speed is too low, the harvesting is difficult, and the threshing and other problems are too high.

3. Adjust the appropriate threshing gap. The minimum gap is not less than 4mm, and the upper sieve should be adjusted according to the maturity of the crop. The upper sieve is 2 3 as the standard, and the lower sieve has also been 2 3 as the standard.

1. Master the appropriate harvester driving speed and feeding amount. Agricultural mechanics mainly consider straw and yield. 2. Master the rotation speed of the reel wheel, the speed is too low, the harvesting is difficult, and the threshing and other problems are caused by too high.

3. Adjust the pin only to complete the appropriate threshing gap. The minimum gap is not less than 4mm, and the upper sieve should be adjusted according to the maturity of the crop. The upper sieve is 2 3 as the standard, and the lower sieve has also been 2 3 as the standard.

If the stripping is not clean, the gap of the pressure feeding roller should be adjusted, and then there is the gap between the upper and lower and left and right sides of the peeling roller.

Capital items refer to the industrial products used by industrial buyers in the process of production and operation, including fixed equipment and auxiliary equipment. Fixed equipment is the main piece of equipment, and the purchase or construction process goes through a long decision-making process.

Summary. Hello, glad to answer for you.

a. The opening of the front part of the sieve is required to be the smallest (generally greater than the length of the crop grains, such as the length of wheat grains is 5-7 mm, so the front opening of the upper sieve should be greater than 7 mm, and it should be opened to about 8 mm);

b. The opening of the front part of the lower screen is slightly greater than that of the front part of the upper screen;

c. The rear part of the lower sieve is slightly larger than the front part of the lower sieve;

d. The opening of the rear part of the upper screen is generally twice that of the front part of the upper screen.

Hello, I have seen your question and am sorting out the answer, please wait a while Hello, I am happy to answer the chain core for you. a. The front part of the sieve requires the smallest opening (generally greater than the length of the crop grains, such as the length of wheat grains in 5-7 mm, so the front opening of the upper sieve should be greater than 7 mm, and it should be opened to 8 mm left rock dust right); b. The opening of the front part of the lower screen is slightly greater than that of the front part of the upper screen; c. The rear part of the lower sieve is slightly larger than the front part of the lower sieve; d. The opening of the rear part of the upper screen is generally twice that of the front part of the upper screen. The opening of these four sieves is generally not to be done again after opening, and it is required to use the hand throttle to start the jujube excavator, and the rated speed of 2200 rpm should be used.