What is the use of having two holes in the bottom of a toilet?

The two holes at the bottom of the toilet are the screw holes that fix the toilet to the ground, but now the toilet is not fixed with screws, and it is usually fixed with glass glue. The toilet is a kind of utensil that we often use in our daily life, and there are many things to pay attention to when using the toilet.

Generally speaking, most families will set up a waste paper basket on the side of the toilet to store used toilet paper, but this will form bacteria to spread with the air, so the waste paper basket next to the toilet bowl is best to be replaced once a day, the longer the storage, the more bacteria will be produced.

When flushing the toilet, it is best to close the lid before flushing, so that some bad things in the toilet bowl cannot be suspended in the air. The cyclone inside the toilet is prone to bacterial growth, and then after a few hours in the air, our toothbrushes, mouthwash cups, and towels will become infected with bacteria.

Keep the toilet brush clean. If the toilet brush is not cleaned and dried, this kind of thing can also become a source of pollution. Every time you brush the toilet, if you don't clean up the dirt on the toilet brush in time, the dirt on the toilet brush will become more and more at this time.

Once the brush is stained with some dirt, be sure to clean it up in time, rinse it well, drain it, spray it with disinfectant, and hang up the toilet brush.

It is a reserved outfall, which refers to the distance between the pit (the distance between the wall and the center of the outfall), which is divided into 30 cm and 40 cm, if the distance from the reserved outfall to the corner of the wall is 30 cm.

The two holes at the bottom of the toilet are reserved sewage outlets, which refer to the pit distance, (the distance between the wall and the center of the sewage outlet), which are divided into 30 cm and 40 cm

The small hole on the side of the bottom of the toilet is used for installationToiletsThe screw at the bottom is a mounting hole.

However, in order to prevent damage to the waterproof layer of the ground, you can also do not install screws, and now many people basically do not use this screw when installing, and will put the sealing ring.

or sealant.

Installed on the toilet, so this hole does not play much of a role now and can be left alone.

However, if it is installed with a seal, it can also effectively seal the seal in place, and at the same time, it can also prevent odors from escaping from the bottom of the toilet.

How to buy a toilet

When buying a toilet, you need to pay attention to the fact that if it is an elderly house, you can replace the split toilet. If it's a newly renovated house, you can choose an integrated toilet.

In addition, the better the quality of the toilet bowl of the same size, the denser and heavier it is. Finally, the size of the toilet is also very important, which is related to whether it can drain water and defecate smoothly.

Summary. There are two small holes in the bottom of the toilet, what is this for? 1.

Auxiliary flushing, cleaning toilet bowl function. 2.To illustrate this problem, we also need to talk about the types of toilets, which are generally called siphon toilets with two eyes under the toilet.

3.The structure of the siphon toilet is that the drainage pipe is of the " type, after the drainage pipe is filled with water, there will be a certain water level difference, and the poop will be discharged by the suction generated by the flushing water in the sewage pipe in the toilet, because the siphon toilet flushing is not with the help of water flow impulse, so the water surface in the pool is larger, and the flushing noise is smaller. Siphon toilets are also divided into two types: vortex siphon and jet siphon.

4.The flush port of the vortex siphon is located on the side of the bottom of the toilet, and the water flow forms a vortex along the pool wall when flushing, which will increase the flushing force of the water flow on the pool wall, and also increase the suction power of the siphon effect, which is more conducive to the discharge of the dirt in the toilet.

There are two small holes in the bottom of the toilet, what is this for?

Please wait patiently for 3 minutes, we are sorting out, and we will answer you immediately, and please do not end the consultation.

There are two small holes in the bottom of the toilet, what is this for? 1.Auxiliary flushing, cleaning toilet bowl function.

2.To illustrate this problem, we also need to talk about the types of toilets, which are generally called siphon toilets with two eyes under the toilet. 3.

The structure of the siphon toilet is that the drainage pipe is of the " type, after the drainage pipe is filled with water, there will be a certain water level difference, and the poop will be discharged by the suction generated by the flushing water in the sewage pipe in the toilet, because the siphon toilet flushing is not with the help of water flow impulse, so the water surface in the pool is larger, and the flushing noise is smaller. Siphon toilets are also divided into two types: vortex siphon and jet siphon. 4.

The flush port of the vortex siphon is located on the side of the bottom of the toilet, and the water flow forms a vortex along the pool wall when flushing, which will increase the flushing force of the water flow on the pool wall, and also increase the suction power of the siphon effect, which is more conducive to the discharge of the dirt in the toilet.

1.Auxiliary flushing, cleaning toilet bowl function. 2.

To illustrate this problem, we also need to talk about the types of toilets, which are generally called siphon toilets with two eyes under the toilet. 3.The structure of the siphon toilet is that the drainage pipe is of the " type, after the drainage pipe is filled with water, there will be a certain water level difference, and the poop will be discharged by the suction generated by the flushing water in the sewage pipe in the toilet, because the siphon toilet flushing is not with the help of water flow impulse, so the water surface in the pool is larger, and the flushing noise is smaller.

Siphon toilets are also divided into two types: vortex siphon and jet siphon. 4.The flush port of the vortex siphon is located on the side of the bottom of the toilet, and the water flow forms a vortex along the pool wall when flushing, which will increase the flushing force of the water flow on the pool wall, and also increase the suction power of the siphon effect, which is more conducive to the discharge of the dirt in the toilet.

What to do with the anti-odor from those two holes in the back.

Okay, pro, wait a minute.

Generally, there will be two symmetrical casting holes behind the toilet, although there is an S-shaped water seal inside the toilet, but the casting holes will still smell back, and you can plug it with glass glue.

There are two holes in the bottom of the toilet, what is the purpose of each?

There are two holes at the bottom of the toilet: one is the sewage hole, and the other is the jet secondary channel, aimed at the center of the sewage outlet, when flushing, part of the water flows out of the water hole around the toilet circle, and part of it is sprayed out by the nozzle, this kind of toilet is on the basis of siphon with the help of a larger water flow impulse, the dirt is quickly flushed away.

The difference between single and double hole toilet bowls.

For those who do not understand the product when choosing the toilet, they can not only look at the difference between their own products, but also look at the difference between their own products.

1. The difference between single hole and double hole of toilet.

1. From the perspective of the two products, the price of single-hole toilets is more expensive, and the price of double-hole toilets is cheaper, which is also the current ** positioning.

2. From the perspective of performance, single-hole toilets are more flexible and smooth, and the design is more reasonable, while double-hole toilets are easy to be clogged and easy to hide dirt and dirt, so they are gradually replaced.

3. From the perspective of maintenance differences, single-hole toilets are easy to maintain, while double-hole toilets are more troublesome to maintain, and maintenance is very expensive.

Second, the analysis of the key points of toilet selection.

1. Use and test water-saving, because it will be used a lot, so you can take a closer look at its water consumption, whether it has a water-saving and energy-saving sign.

2. Look at the glaze is also the basic selection point, feel whether its glaze is smooth and flat by hand, if the glaze is rough, the surface of its workmanship is poor, easy to scratch, and easy to block.

3. Look at the gloss.

It is important to choose a toilet bowl, if the toilet bowl has a higher gloss, it will be denser and easier to clean.

4. Listening to the sound is the way to distinguish, the sound is crisp, it means that its water tank is smooth, and it is smooth to use, if it is stuck when pressed halfway, it means that the quality of its water tank is not good, which affects the use.

It is located on both sides of the bottom of the toilet.

The two small holes in the toilet base are the toilet foot screw mounting holes. Due to the possibility of damaging the waterproof layer of the ground, the foot screws of the toilet are basically not installed, and the toilet is installed by a sealing ring with silicone sealant.

If the toilet leaks here, it means that the sealing ring is not installed or the installation is not in place, the flush can not be drained from the sewer pipe, and some of the water will flow to the base area, if the hole is not sealed, it will come out, and the installer will generally seal the two holes with glue to prevent the sealing ring from failing.

How to install two holes in the bottom of the toilet?

First, the screw hole should be embedded in the ground and the embedded expansion bolt should be buried; Then tighten the expansion bolt and let the expansion screw completely release; Then unscrew the screws, put the toilet bowl away, and tighten the screw connectors. However, due to the fact that drilling screw holes is easy to damage the ground waterproof layer, it is basically not installed now, and it can be directly sealed and installed with glass glue.

What should I pay attention to when installing a toilet?

1. Before installing the toilet, check the sewage pipe, check whether there is mud, sand, waste paper and other sundries inside, and check whether the installation ground is flat. If there is unevenness, you can cut the toilet drain, 2-5 mm higher than the ground.

2. Choose the toilet according to the distance from the water at home, generally only two standards of millimeters, and before the toilet is installed, you should carefully read the instructions to verify the integrity of the accessories. Avoid cutting corners and shoddy.