What are the anti slip methods for the ground to freeze

Non-slipWalking Notes:

1. Wear a pair of non-slip shoes when you go out, preferably with rubber soles. When going out in winter, you must keep abreast of the road conditions, generally if the temperature is particularly low and it has just rained or snowed in front, then the road will definitely be icy. Try not to wear high heels and leather shoes, because they have poor slip resistance and are very prone to slipping.

2. Wear thicker clothing. Sometimes the road is really slippery and you have to go out, so it's inevitable that you will slip (slipping is common in the northern winter). At this time, if you dress thicker, then you won't feel so painful. Of course, try to avoid slipping.

3. Walk slowly, in this case, if you are still in a hurry, then it can only be a slippery rhythm. After all, you can't walk, the ice is on the road. If there is a railing or something else next to you that will prevent you from falling, you can grab it.

4. Use anti-slip tools. There are also a lot of anti-slip tools** on the market** that can be attached to boots, so as to strengthen resistance when walking and avoid slipping and falling.

5. If you accidentally slip, remember not to use your hands to support the ground, which can easily lead to fractures.

Wounded. Also, protect your head in time to avoid direct contact between your head and the ground. If the situation is serious, be sure to call 120 in time.

When driving through icy roads, drive slowly, do not overtake at will, tap the accelerator, tap the brakes, slow down the direction, any big movement or improper operation may bring danger. If necessary, the tire can be deflated to increase the contact area between the car and the slippery road surface and enhance the tire adhesion; The ice and snow road should be slowly lifted and refueled slowly at any time, and it is easy to slide or idle when refueling vigorously; Remember to keep your distance, as vehicles in front and behind you may roll or slide sideways when braking or starting.

In addition, if the road surface is icy, there is another measure to prevent skidding - sprinkling salt on the road surface in winter can make the snow water less likely to form ice; It is also possible to increase friction by sprinkling sand and coal ash on the road surface.

If only it was a short road. Spread dirt, gravel, branches and dead grass on the ground. If the trail is very long, you will need to install snow chains or special snow tires on the wheels.

If you are walking on foot, sprinkle some sand, stones (to increase friction) and salt (to increase friction and prevent freezing) on the road; Wear non-slip shoes. If you're driving, put a few turns of chains on the tires (to increase friction).

1. Reduce the speed of the vehicle. Drive at the speed predicted on the highway variable information display board to prevent the vehicle from skidding and shorten the braking distance.

2. Increase the distance between vehicles. The distance between vehicles on ice and snow roads should be 2 or 3 times that of dry roads.

3. Drive along the rut of the car in front, and generally do not overtake, accelerate, make sharp turns or brake urgently. When you need to stop, you should take measures in advance, use more gear shifting, and less braking to prevent side slipping caused by various reasons.

4. When driving on curves or ramps with ice and snow, slow down in advance.

5. Install tire snow chains or change to snow tires in time.

For large trucks, it is better to use iron snow chains for icy and slippery roads, while for private cars, rubber snow chains can be used.

At present, the more common snow chains are iron snow chains, beef tendon snow chains and rubber snow chains. There are also some precautions for installing snow chains, snow chains need to be installed on the driving wheels, if it is a four-wheel drive vehicle, all four wheels need to be installed; If it is a 2WD vehicle, it needs to be installed only on the drive wheels, of course, it is more secure to install it all.

Also, after installing the snow chains, the owner needs to control the speed of the car during driving, remember to slow down, the speed should be controlled as much as possible within 40 kilometers per hour, and do not carry out sharp acceleration, sharp deceleration, sharp turns and other operations.

If you are driving on a normal road, you should also remove the snow chains on the wheels in time. Because if snow chains are still used on the normal road surface, there will be certain consequences, which will restrict the driving of the owner, affect the driving experience and riding experience, and cause a certain degree of damage to the vehicle.

Therefore, it is necessary to use snow chains in an appropriate environment to better protect our travel, reduce certain safety hazards, and have a better driving experience.

The rubber snow chain is made of pure rubber, which has strong tensile resistance and ductility, and should not be broken at low temperatures, and the installation method is relatively simple and convenient.

Generally, snow chains are installed on the driving wheels, if it is a four-wheel drive vehicle, all four wheels need to be installed with snow chains, and if it is a front-wheel drive car or a rear-wheel drive vehicle, two driving wheels can be installed or all of them can be installed.

However, it is recommended that if the owner has the conditions, it will be more appropriate to install all the wheels together, and it will be relatively safe, such as only installing snow chains on the two driving wheels behind the rear-wheel drive car, which will make the front wheels not have a good grip and lose their pointing ability, which will cause deviation and other phenomena, which has a certain danger.

It should be noted that the use of snow chains must be used on ice and snow roads, and the use of snow chains on snow-free roads will cause damage to tires and road surfaces, and when using snow chains, you should also pay attention to the speed, remember to slow down, try to control the speed within 50 kilometers and hours, and do not carry out sharp turns, sharp braking, rapid forward and other operations.

Iron snow chains are better, and iron snow chains are more capable of helping cars catch the ground when it is snowing.

It is better to choose iron snow chains as much as possible, and such anti-slip mats are also stronger, and the anti-slip effect is also very good.

When it snows, snow chains made of iron chains for tires have a better effect, are stronger, and are not easy for the car to roll over.

You should choose some good quality snow chains, and you should also choose some snow chains with relatively large resistance, which can increase friction well.

You can choose a special tire one, you must choose a more cost-effective one, you must choose a more stable one, the ground is more slippery, the snow is relatively large, try not to go out by car.

Method 1: De-icing with snow melting agent.

If the ground freezes and it interferes with travel, you can melt the ice by sprinkling snow melt on the ground. Once the snow and ice have melted, the snow and ice can be quickly cleared. This is one of the more commonly used methods of de-icing and snowing.

Method 2: Sprinkle salt and de-ice.

Or you can sprinkle salt on the ground to melt the ice. Just sprinkle a light layer of salt and let it sit for about fifteen minutes to quickly melt the ice, which can then be easily removed.

If the ground is too frozen, it will take about 30 minutes or more to melt the ice. Salt lowers the freezing point of water, and after the snow has melted, a layer of salt sprinkled can prevent the melted ice from condensing again.

Method 3: De-icing hot water.

It can also be de-iced by pouring hot water over the ice. This method can easily melt the ice, but it is important to de-ice the ice quickly when it melts to prevent the melted ice water from condensing again.

However, hot water de-icing actually has many drawbacks, such as a large amount of repetition, high cost and dangerous operation. Therefore, de-icing with hot water is only suitable for de-icing small areas.

1. Use an ice shovel to shovel.

2. Sprinkle salt to promote rapid dissolution (currently used in too many cities) 3. Sprinkle carbon black to promote heat absorption and accelerate dissolution.

4. Cover the grass and cover it with the heat absorbed by it to slowly dissolve.

Different methods can be used in different situations. For your choice.

You can sprinkle slag, salt, etc. Or just shovel it.

1. The snow on the road becomes ice, and the usual way to do it quietly is to spread chemical agents, which is usually used in the world for road surface de-icing, and the ice and snow melting agents mainly include salt substances and alcohol cluster matrix.

2. However, this method will be greatly affected by the ambient temperature, as long as the ambient temperature drops, the melted snow will freeze into ice again, so that the road surface will be more slippery.

3. If the snowfall is too large or the ambient temperature is too low, it is difficult for the snow melting agent itself to dissolve and melt quickly, so it has to be rolled by vehicle tires.

4. There is also to sprinkle some salt, cinder, and materials with a certain particle size on the ice and snow Qizhengheng pavement, which can improve the friction coefficient of the ice and snow pavement.

1. The snow on the road is turned into ice, and the usual method is to spread chemical agents, which is usually used in the international community for road surface de-icing, and the ice and snow melting agents mainly include salt substances and alcohol substances.

2. However, this method will be greatly affected by the ambient temperature, as long as the ambient temperature drops, the melted snow will freeze into ice again, so that the road surface will be more slippery.

3. If the snowfall is too large or the ambient temperature is too low, the snow melting agent itself is difficult to dissolve and melt quickly, so it has to be rolled by the tires of the vehicle.

4. There is also to sprinkle some salt, cinder, and materials with a certain particle size on the ice and snow pavement, which can improve the friction coefficient of the ice and snow pavement.

Methods of ground icing treatment:

1. Use an ice shovel to shovel.

2. Sprinkle salt to promote rapid dissolution (currently used in many cities where it is passable and too noisy).

3. Sprinkle carbon black to promote heat absorption and accelerate dissolving.

4. Cover the grass and cover it with the heat absorbed by it to slowly dissolve.

Different methods can be used in different situations.

1. Use anti-synovial fluid for "formless" anti-slip treatment.

Anti-slip liquid is a product that is coated on ceramic tiles, polished tiles, glazed tiles, artificial stones and other ground materials to play an anti-slip role. The principle is that this liquid penetrates into the surface of the ground material, and when it is in contact with the sole of the foot, it forms a suction cup to achieve the purpose of anti-slip, and the friction coefficient reaches 0 5 0 8, which has a good effect on wet ground. According to the lack of various floor materials, such as marble, balance finger granite, ceramic tiles, artificial stone, wood flooring, concrete, etc., choose the corresponding type of non-slip material.

2. Use the stamper tool to carry out the "pressure mode" anti-slip treatment.

Molded flooring is a kind of green environmental protection floor material that has been popular in the United States, Canada, Australia, Europe and has been rapidly promoted in major developed countries in the world in recent years. It can create a variety of natural marble, granite, bricks, tiles, wooden floors and other laying effects on the surface of the original ordinary new and old concrete, with beautiful and natural graphics, real and durable colors, and strong and durable texture.

The molded floor made of Ruiyi environmental protection hardener material has the characteristics of wear-resistant, anti-slip, anti-freezing, not easy to dust, easy to clean, high strength, impact resistance, and a wide range of selectivity in terms of color and style, low cost and green environmental protection, etc., which is an ideal choice in the fields of garden, municipal, parking lot, park path, commercial and cultural facilities.

3. Use metal and other materials for "concave and convex" anti-slip treatment.

The tread surface layer should be easy to walk on, wear-resistant, non-slip and easy to clean The practice of the ground layer of the same building is basically the same. Commonly used are cement mortar surface layer, terrazzo surface layer, stone surface layer, cylinder brick surface layer, non-slip floor tile surface layer, carpet surface layer, etc., such as in order to avoid pedestrians slipping when walking, the tread surface layer is the largest stair tread surface should be equipped with anti-slip strips, and at the same time play a role in protecting the tread angle. The anti-slip strip is usually located close to the tread, but it should not be too high, otherwise it will cause inconvenience in walking The commonly used anti-slip strip materials are cement iron filings, corundum, metal strips (cast iron, aluminum strips, copper strips), ceramic mosaic tiles, etc.

4. Use resins and new epoxy materials for "covering" anti-slip treatment.

Polyurethane flooring refers to the use of polyurethane floor coating combined with a new solvent-free or water-based, pollution-free ground functional construction technology to meet some specific use requirements (high-end conference or entertainment centers focus on comfort requirements; Industrial and mining enterprises pay attention to anti-corrosion and wear-resistant requirements; The food industry pays attention to high and low temperature resistance, and the logistics industry requires rapid use, etc.), so it is especially suitable for the coating of floors with anti-slip, anti-corrosion and wear-resistant requirements in various industrial and mining enterprise workshops, parking lots, sports fields, etc. The new generation of polyurethane flooring is mainly a generation of new flooring to replace epoxy flooring, and it is more wear-resistant, flexible, and convenient to construct, and the floor construction can meet the use requirements after 2 hours, which completely changes the time problem that enterprises are concerned about floor renovation. It is widely used in machinery, food, electronics, chemical, pharmaceutical, tobacco, textile, furniture, light industry, plastics, stationery and sports supplies, etc.