-
The ball lock removal process is as follows:1. First find a small tool at hand, such as a thin wire or a slotted driver, and then find the small hole on the side of the lock, and then use the gadget to card the small hole on the side lock, pay attention to the downward direction from the inside in.
2.Then remove the collar and spiral twist that decorate the door lock, you can see that there are two fixed screws, and then use a screw to screw it down, you can pull the ball door handle on the outside side out of the hole.
3.In the end, only the side deadbolt remains, which is held in place by two screws and removed with a driver.
-
How to remove and install a ball lock?
-
If the door is open:
Both inside and outside the handle, there is a small hole in the side. After turning a certain angle in the direction of opening, you can see the bayonet in the small hole. Hold it down with a pointed object and pull out the handle at the same time.
Let's see for yourself. Some locks have to be turned in the other direction to see the bayonet.
If the door is locked and there is no key, and the person is outside:
You can use small scissors to insert into the small hole, cut it to the bayonet (the iron sheet is very thin and easy to cut), and then press down the bayonet and pull out the handle. When you put it back on, the incision is smoothed out, and you can't see it if you don't want to see it (usually on the side or underneath).
-
Ball removal steps on the outside of the spherical lock:1. Use the iron piece attached to the ball lock fitting to remove the handle and insert it into the small hole under the handle.
2. Follow the previous steps and the handle can be easily unscrewed.
3. Tie the latch in the small hole on the side of the door panel, press down on the latch so that the protruding part is stuck in the notch, and turn the door handle to ensure that the latch is well connected with the lock.
4. Install the ring, tighten the screws, turn the door handle after tightening, confirm that the ring is correct, and install the rear door handle.
5. Fix the bayonet of the door hole of the screw box on the bolt, and try not to lock the door after installation.
6. Use an electric screwdriver or Phillips screwdriver to remove the locking bolts.
-
To remove the ball lock on the door, you need the following tools: a Phillips screwdriver.
-
Disassemble the handle first, there is a spring steel wire pin or spring steel sheet pin at the junction of the handle shaft, and the handle can be removed by poking the spring or spring wire with a tool.
Then remove the deadbolt, remove the deadbolt fixing screw, and rotate the deadbolt 90 degrees to remove the lower deadbolt.
Finally, the decorative pieces at both ends of the handle shaft are removed, and some locks have decorative pieces only on one side The decorative pieces are also fixed with spring steel wires, and the decorative pieces can be removed by poking the steel wire with a tool, and the screws on the lock body fixing clip pieces are unscrewed after removing the decorative pieces, and after unscrewing, the spherical lock rotating mechanical theme can be removed, and the spherical lock is disassembled.
-
Use a small flat file to break the front knife edge, then put it on the lock mouth to align, hit it with the appropriate force of the hammer, break each marble inside, and finally take out the lock bladder, but the original lock will be abolished, and it should be replaced with a new one. Hope to choose, thank you! Just break off the tip of the small file Actually, it's my words.
Blew the door straight away.
-
When you buy a lock, bring something that you know the key, first use it to remove the handle behind the lock, then unscrew the lid inside, and then use a plum blossom driver to remove it.
-
The steps for installing and removing the spherical door lock are as follows:
Tool materials: electric drills, screwdrivers, tape measures, hole openers, woodworking poke knives.
1. Positioning of the size of the lock groove: in the direction of opening the door, measure the size of the lock groove (about 900 mm) on the ground on the inside of the door sleeve, according to the size and depth of the lock groove, make a lock groove with a carpentry poke knife, put on the plastic gasket, close the lock plate of the lock groove, and fix it with self-tapping screws.
2. Lock body size positioning: close the lock tongue with the lock body, and use a tape measure to measure the size (70 mm) of the lock tongue baffle from the center point of the lock body, which is the size of the corresponding lock body in the door opening.
3. Door lock body opening positioning: it is known that the lock body is 70 mm away from the lock tongue baffle, close the door leaf, find out the center point of the parallel lock groove baffle, draw a parallel line greater than 70 mm, and then measure 70 mm from the edge of the door leaf (find the upper, middle and lower, three positioning points), and the distance from the parallel line up and down is about 100 mm, and the accurate position of the lock body opening can be obtained.
4. Spherical lock lock body opening: measure the diameter of the concave and convex round mouth in the inner side baffle of the lock body, that is, greater than the lock body aperture (50 mm), according to the positioning before the uproar, the hole opener is used to punch the limb Lu Kai hole at the position of the cross marking point, and then the deadbolt hole is opened with an electric drill on the side.
5. Install the lock body: put the lock body into the opening hole from the front (the direction of the bedroom door), the lock body and the deadbolt joint correspond to the deadbolt hole, connect the deadbolt buckle firmly with it, fix the deadbolt baffle plate with self-tapping screws, and then adjust the position of the lock body installation block on the back of the door, fix it with a nut, screw on the cover and press the handle.
Lock installation learning and ball lock installation.
Quite simply, do you put the back of the lock unfit with 2 screws that fix the lock panel? You disassemble the 2 screws, the panel will be removed, and then you will see the front and back of the cover lock cylinder 2 covers, there are 2 screws on the two sides of the cover, disassemble and remove the cover plate, you will see the head of the lock cylinder, and then on the side of the lock on the side of the lock tongue there is a screw that fixes the lock cylinder (the screw in the horizontal position of the lock cylinder), remove the screws and then you remember to insert the lock cylinder The position of the lock cylinder must be horizontal, so that you can remove the lock cylinder, and then insert the lock cylinder according to the original lock cylinder position length after removing the lock cylinder. Then install it in the order you just dismantled, remember to install the iron rod of the shaft at the position of the lock handle when installing the panel, according to the method you just disassembled, (remember that there is a bolt below the panel to insert the hole where the bolt is placed), and there may be a new lock cylinder that is still inflexible, that is, the upper and lower tongues of your upper and lower connecting rods are rusty, if the installation is not flexible, you can disassemble the screws of the upper and lower deadbolts, take the cover of the deadbolt, and apply some oil.
1. Check whether the signs outside the packaging of the purchased products are complete (including the relevant implementation standards of the product, the name and address of the manufacturer, and the date of production), whether the packaging is firm, and whether the content of the manual is consistent with the product itself, so as to prevent the exaggeration of some products and the fact that they are not consistent. >>>More
Remove the old door lock before installing it. >>>More
Let me introduce to you some matters to pay attention to in the maintenance of door locks: 1. Don't use lubricant casually Some friends often like to drip some lubricating oil on the keyhole when the door lock is astringent or tight, so that the whole body of the door lock may be smooth immediately, but because the oil is easy to stick to the ash, it will be easy to slowly accumulate dust in the keyhole in the future, and form putty, which makes the door lock more likely to malfunction. The right solution: >>>More