What to do if the heating pipe is broken and leaking, what should I do if the radiator is cracked an

If the heating pipe is broken and leaking, turn off the main valve immediately, and then find a plumber to fix it as soon as possible, and then you can continue to open the valve and continue to heat.

First of all, the heating pipe valve should be closed first, so that the water inlet should be cut off first, and then the ** should be repaired by professionals, so as not to leave hidden dangers due to improper repair.

Close the main valve first to avoid continuous leakage, and then find someone to repair it.

Make a note of the leak and quickly close the heating valves.

Usually, there is a locking valve at the connection between the inlet and return pipes and the radiator of each group of radiators, which is used to shut off the group of radiators during maintenance or overhaul. If a certain group of radiators leaks a large amount of water, you should find the control valve of the leaking radiator, and the valve rotates clockwise until it cannot be screwed, so that the group of radiators is turned off.

It should be noted that the design of radiator heating system in new buildings is usually double-pipe parallel, and the advantage of this heating system is that turning off a certain group of radiators will not affect the normal heating of radiators in other rooms. However, if it is a tandem heating system, it should be noted that after the first set of radiators is turned off, it may affect the heating of radiators in other rooms.

There is also a more old-fashioned heating system, the whole building and each floor share a master valve, each group of radiators does not have a lock valve, to turn off the leaking radiator, you need to contact the property or heating company in time to ask it to close the main valve, do not turn off privately, otherwise it will affect the normal heating of the users of the floor. However, the number of such heating systems is very small.

For a small amount of gaskets, joints, and small leakage of sand holes, a larger container can be used to connect the water in an emergency to avoid soaking the ground, and the radiator can still be heated normally. However, the third step mentioned in this article must be taken immediately, and it is absolutely necessary not to compromise in order to prevent the leakage from becoming larger and causing greater losses.

What should I do if the radiator cracks?

1. Water leakage at the connection point of the heating system.

The most likely place for the radiator to leak is the connection point of the heating system, once the connection is loose or not connected well, then the leakage is certain. If you find that there is a leak at the connection point, you should close the valve immediately and then contact the maintenance personnel to repair it. However, if the water leakage is not very serious, and someone knows a little professional maintenance knowledge and has complete tools, you can try to solve it yourself, and you can save a maintenance fee.

Of course, the premise is that it is not serious and someone in the family understands the pure car key, otherwise in this winter, it is better to spend more money and not find guilt!

2. Leakage of sand hole in the heating pipe.

If the radiator is leaking, you need to wrap a towel or rag around the tube, and then set aside a section and put it in the basin to draw water in. Friends who have a bicycle inner tube at home and don't use it, you can cut it into a section of 1cm wide and 50cm long, and then pull the inner tube 3cm away from the trachoma, and wrap it around the trachoma 3cm with a buckle, and wait until 3-5 days later, the trachoma will automatically rust to death.

3. The exhaust valve is broken and leaking.

Sometimes in the process of water injection and pressure test, some pipes will enter the air, and some owners will unscrew the exhaust valve by themselves to give up, and then improper operation will lead to water leakage. At this time, it is recommended that you quickly use a chopstick as a wedge to nail into the leakage and find a professional to repair it.

4. The radiator bursts and leaks.

If it is a leak caused by the bursting of the radiator, the sail bucket is terrible, quickly use thick towels, rags and other more absorbent items to plug the leakage, if it is a house with one ring, it is necessary to close the valve as soon as possible, call the maintenance of the district heating unit, and find someone to repair.

If the leak is small, you can buy two tubes of cement glue online and smear it on the leakage.

If there are many leaks, you can deal with them like this.

1.For example, the trachoma of the radiator leaking is very large, and the water leakage is very serious. It must be replaced, it cannot be repaired.

2.If the radiator is made of alloy, even if the trachoma is small. It can't be repaired either, so replace it with the best policy.

3.If it is a traditional iron radiator, the trachoma is very small and the water leakage is not serious, then you don't need to pay attention to it, just find a container to receive the leaked water, and the trachoma will be embroidered by itself in the next heating period. No more water leaks.

<>1. Find the cause of the heating pipe leakage. First, close the valve of the heating pipe and the valve of the water separator, and then open the valve of the water separator to release the pressure. 2. Investigate the cause of water leakage of heating pipes.

Find out whether there are cracks in the heating pipe, whether the interface is intact, etc., if it is because of the sand hole in the iron pipe, remove the inner tube of a section of the bicycle and deal with the leakage. If there is a sand hole in the heating pipe, wrap it in a towel and then treat it with a bicycle inner tube. 3. In the case of serious water leakage, you can directly choose to replace it with PPR pipe, which is corrosion-resistant, long-life, and low-cost, so as to avoid greater losses.

The water leakage treatment method of the heating pipe is that the water leakage is more serious, and there are many water leaks, the good way is to change the PPR pipe, which is corrosion-resistant and heat-resistant, and has a long life. The pipeline is complex, it is difficult to change the pipe, and the leakage area is large, use a raw meal belt, wrap the leakage, wrap it a few more times, and then wrap it with aluminum foil outside, if the sand hole is not big, it can also be solved.

If there is no leak point in the ground, the pipes in the heating ditch may leak, so the heating ditch needs to be inspected. It is recommended to find a professional. If the radiator is leaking, close the water supply and return valves next to the radiator and adjust the manual release valve on the radiator.

If it is missing, replace the parts in time, if the pipeline leaks, you need to close the control valve of the leaking pipeline, after determining the position of the control valve, turn the valve handwheel clockwise by hand until it can not be rotated.

If the problem of water leakage is more serious, it is also necessary to plug the leakage. Choose a coagulant and apply it to the leaky joints, but you need to wipe it clean and apply it evenly. After solidification, it can form a plugging effect.

If there is an aging problem at the joint, replace the interface, and the relevant accessories or heating pipes can also be replaced, so as to avoid the trouble of water leakage again in the future.

Kiss! Hello, happy to answer your <>

1. First of all, we need to understand the cause of water seepage, and then solve it in combination with the cause. Close the heating valve first, then open the air valve, and empty all the pressure inside. 2. It may be that the pipeline has been used for a long time, and there are some trachoma causing water leakage, which is not difficult to deal with.

Prepare an inner tube of the bicycle, wipe the surface clean, then stretch it in the leaky place, buckle it, and then tie it tightly with a wire, it will rust to death after a long time. 3. The water leakage is not particularly serious, and the surface can also be wiped clean first, and then pasted with a special sealant, which can play a role in sealing. In addition, glass glue can also be used, it is best to choose neutral, otherwise the acidic one will have a corrosive effect.

4. If the water leakage is more serious, in this case, it is best to replace it with a new pipe, replace it with PE material, which is better for its pressure resistance, and then wrap the raw meal belt, wrap it a few more times, and finally wrap it in aluminum foil. 5. If there is a problem of water leakage at the head, the joint needs to be replaced, especially at the interface of the valve, which is most likely to leak. 6. If there is water leakage in the valve, it may be that the sealing ring inside is damaged.

It is necessary to replace the gasket and then reinstall it back to burn it. 7. The last method, if you really don't know it, you can only ask professional personnel to come to the door to solve the maintenance. I hope I can help you <>

Do you have any other questions?