How to wear shoelaces for leather shoes with 3 holes, and how to perforate shoelaces?

Three ways to tie your shoelaces.

Lattice system. 1.Thread the head of the shoe straight through the bottom (gray part) and up from the underside of each hole.

2.Skip the two rows of holes, cross and thread into the fourth row.

3.The two ends of the laces are vertically downwards and skip one row of holes and are threaded by the second row of holes.

Go out. 4.Repeat steps 2 and 3 to thread through the fifth row of holes, then straight down through the third row of holes.

5.It is completed by crossing and exiting through the top hole.

European-style flat straight system.

1.Thread the head of the shoe straight from the bottom (grey part) into the bottom two holes at the bottom.

2.One end of the lace (the light end) is worn diagonally diagonally from the bottom up and straight into another hole in the transverse second row.

3.The other end of the lace (the dark end) is diagonally diagonally threaded through the third row of holes from bottom to top and straight into the other hole.

4.Repeat the operation, alternating the two lace heads.

Trapezoidal knotting method.

1.After adjusting the length of the ends of the laces, pull out the laces from the inside out.

2.Pull out the laces and thread them into the second hole from the outside in.

3.The left lace is worn under the lace between the two holes on the right, and the right side is the same.

4.Repeat the operation.

Hello, thread the head of the shoe straight from the bottom to the bottom of the two holes. One end of the lace is diagonally threaded diagonally from the bottom up and straight into another hole in the transverse second row. The other end of the lace is diagonally diagonally through the third row of holes from bottom to top and straight into the other hole.

Look good with shoelaces**, the specific steps are as follows:

1. First, align the ends of the laces, and then pass through the holes on both sides, as shown in the inner and lower volume diagrams.

2. Next, after the shoelaces are put on, cross them as shown in the figure below.

3. Then, the shoelace holes in the back can be threaded in the same way, as shown in the figure below.

4. Next, when going through the hole in the middle of the shoe, put both laces through the hole, as shown in the picture below.

5. Then, according to the above crossing method, at this time, you can wear to the last lace hole, as shown in the figure below.

6. Finally, when wearing, you can unify the upper and lower shoelaces on the left side, which will be more beautiful, as shown in the figure below.

Kiss! Hello, happy to answer your <>

Pro, shoelace perforation method: 01, first of all, under the shoehole, carefully wear the shoelaces in accordance with the top-down way, and the shoelaces are worn to the bottom with the upper shoeholes, which will be visually more beautiful, and there will be no visual effect that the lace is layered below. 02. Next, follow the Z-shaped route and pass the shoelaces through the third shoehole.

It should be noted that there is a shoehole in the middle, which is operated in order to tie a straight and beautiful shoelace shape at the back. 03. The old god on the other side of the shoelace passes through the second shoehole on the opposite side, because the second shoehole is worn here, and the back can pass through the second shoehole on the opposite side in parallel, creating a straight carrying effect. 04. The next step is to follow the same wiring and steps for piercing, in fact, as long as you master the rules, the operation is also very simple.

05. According to this Z-shaped way, through all the holes, the good-looking McQueen shoelaces are tied, I hope mine can help you <>

If you have any other questions, you can ask me again<>

Hello, I am happy to serve you and give you the following answers: Piercing shoes are a simple way to wear, but sometimes there will be difficult piercing. Original Quiet Crude Cause:

1.Shoelaces that are too stiff: Some laces are too stiff and can be resisted when pierced, making them difficult to pierce.

2.Shoelaces are too soft: Some laces are too soft and can be stretched when pierced, making them difficult.

Workaround:1Use a shoelace piercer:

A needle can be used, the lace is placed on the needle, and the lace is pulled out so firmly that it is perforated. Steps:1

Prepare the lace piercer or needle: Prepare the lace piercer or needle for the piercing shoe belt. 2.

Place the laces on the perforator: Place the shoelaces on the perforator and press down on the perforator to perforate the shoelaces. 3.

Place the lace on the needle: Place the lace on the needle and pull the lace out so firmly that it is perforated. Personal Experience:

Perforated laces can make your shoes more delicate, but sometimes it is difficult to pierce, in which case you can use a shoelace piercer or needle to help you pierce your shoelaces. In addition, when piercing shoelaces, pay attention to the material of the laces, if they are too hard or too soft, it will affect the effect of the piercing.

Hello, it is a pleasure to serve you and give you the following answers: Steps to pierce shoelaces:1

Prepare a pair of scissors with a sharp needle tip, a shoelace, a thin needle or a sharp thread picker; 2.Place the shoelaces on the plane of the sock posture, and pull out a small hole with scissors at the positive position of the shoelaces; 3.Use a thin needle or a sharp thread picker to widen the small hole and draw it to a suitable size; 4.

Put one end of the lace into the small hole that is pulled out, put the other end into the other side, and the piercing is completed; 5.If the laces are too short, you can add a clasp to the two good ends of the laces to allow for perforations; 6.If the laces are too long, you can add a buckle to one end of the laces, cut the other end with scissors, and then perforate them; Personal Tips:

1.When piercing shoelaces, be sure to use sharp scissors or thread pickers to avoid shoelace breakage; 2.When piercing, avoid pulling out too large a small hole to avoid slipping out of the laces; 3.

If the laces are too short or too long, you can add buckles to the ends of the laces to allow for perforations.