Crystal epoxy tutorial, how to clean crystal epoxy?

1. Place the object flat on the countertop and wait for the drip.

2. According to the dosage, take a cup, accurately weigh A glue and B glue, mix and stir evenly according to the ratio of 3:1.

3. Take a clean syringe, suck the prepared glue into the syringe and evenly drip it on the surface of signs, trademarks, etc.

4. 3 to 5 minutes after instilling crystal glue, observe whether there are bubbles or dust particles on the rubber surface, if there are small bubbles, you can use a small needle to pick it off.

The poured epoxy glue is cured at room temperature of 20 to 22 for 10 hours to harden to become a crystal epoxy glue that does not stick to the surface. After the drip plastic, the container needs to be cleaned, after the glue hardens, it is insoluble in any solvent, and the machine and container need to be cleaned before it is hardened.

The storage period of crystal epoxy is generally 6 months, and it can still be used if the performance is good for more than 6 months. When using the configured crystal glue and encountering the remaining glue, do not pour it back into the original unconfigured package, so as not to react and cause jelly.

Crystal glue needs to be sealed in a ventilated, cool and dry place, and the shelf life can reach 360 days.

Crystal epoxy is a common handmade material that can be used to make various jewelry, bracelets, earrings, etc. Here's a simple crystal glue tutorial to help you get started quickly making crystal jewelry.

Preparation of materials:1Crystal beads: You can choose crystal beads of different colors and shapes according to your preference.

2.Dispensing gun: used to drip glue evenly on the crystal beads.

3.Glue stick: The glue used to load the glue dispensing gun.

4.Jewelry accessories: such as bracelets, studs, etc., which are used to fasten the crystal beads to them.

5.Wire or pliers: used to attach jewelry accessories to crystal beads.

Steps:1Plug the dispensing gun into a power source and preheat it for a few minutes until the glue melts completely.

2.Insert the glue stick into the dispensing gun and wait for the glue to melt.

3.Place the crystal beads on a flat bench and prepare to start dispensing.

4.Aim the glue dispenser at the bottom of the crystal beads and gently press the trigger of the glue gun to let the glue drip evenly on the crystal beads. You can choose the amount and location of the dispenses according to your preference.

5.Wait for the glue to dry completely, which usually takes a few minutes to ten minutes.

6.Insert wire or pliers into the glue on the crystal beads to secure the jewelry accessories. Make sure the jewelry accessories are securely fastened to the crystal beads.

7.Check whether the crystal jewelry is firm, if there is a loose place, you can drip the glue again.

8.When you're done, wait for the glue to dry completely to make sure the crystal jewelry is firm and reliable.

Notes:1Be careful of burns when using the dispensing gun to avoid dripping glue onto your hands.

2.Pay attention to the uniformity and quantity of glue when dispensing glue, and avoid too much or too little glue.

3.When fixing the jewelry accessories, it is necessary to ensure that they are firm and reliable to avoid the jewelry from falling.

4.Pay attention to ventilation when using glue and avoid inhaling harmful gases.

The above is a simple crystal drip tutorial, I hope it can help you. It takes a certain amount of patience and care to make crystal jewelry, and I believe you can make beautiful crystal jewelry!

1.Soap washing.

If the epoxy is not completely dry, you can wipe the epoxy with a paper towel, wipe the undried part, then apply soap to the place where the epoxy remains, wipe it with your hands, and finally wash it with water.

2.Soak in hot water.

If the glue has cured, use a hot towel. Soak the towel in hot water, wait for the towel to soak, take it out, wring it out, fold it, then apply it to the drops, wait for the drops to soften, and then easily remove them.

3.Alcohol rub.

If the drops are difficult to clean, apply alcohol to the area containing the drops, wait for the alcohol to break down, and then wipe them clean with a damp cloth or use a cotton swab dipped in alcohol to wipe the drops clean.

Toilet water has a good cleaning effect.

Crystal glue is a chemical glue that can be cleaned with an acidic solution. In general, you can choose to remove it with acetic acid, soak the part with crystal glue with white vinegar, and wash it with water after dissolving.

You can use crystal drops to dip your hands and wash them with shower gel, and you can wear disposable gloves or clean plastic bags on your hands during operation, and then scrub them clean with laundry detergent.

If you want to drop glue like this crystal, you can use something strict, or something like dish soap, that has a strong smile, and wash it off.

First of all, you should clean this thing out and put it back in its original place.

It is better to soak in laundry detergent for a while or wash with warm water.

The crystal glue tutorial is as follows:

1. A group of crystal epoxy glue (epoxy resin A and B glue) is two cans, and the ratio is A glue 3: B glue 1.

2. Use the stirring rod to slowly stir well until it is completely transparent (without a trace of it).

3. Pour the glue into the silicone mold, pour it into the 4 1 bottom layer first, and put it in the box to wait for hardening.

4. Put the insect specimen in, confirm the position, and then continue to pour the glue slowly.

5. After the demoulding is completed, the bottom or edges and corners, if it is uneven, sandpaper can be used to polish.

Materials required for crystal epoxy:

Crystal epoxy glue (epoxy resin A, B glue), dried insect specimens, electronic scales, silicone molds, sandpaper, plastic droppers, disposable plastic cups, disposable chopsticks, gloves, pins, tweezers, stirring rods, dust box.

Crystal Epoxy Tutorial:

Main materials: about 40g of crystal epoxy glue AB glue, bracelet silicone mold, dried flowers blue and red branches full of stars, small broken stones black and white, color essence (red, sky blue, white), toothpicks, droppers, tweezers, plastic cups.

Production steps: 1. Prepare a group photo of the materials.

2. Mix the glue according to the quality ratio of 3 to 1.

3. Stir clockwise or counterclockwise along the edge of the plastic cup until there is no flocculent at all, bubbles may appear, and let stand until the bubbles disappear.

4. Arrange flowers for the mold while standing, and pour part of the glue after standing, no more than half of the mold.

5. Take part of the transparent glue and fine-tune it to white, and take the dropper and drop it into the mold (disperse the drop).

6. The toothpick head skims off the color essence, pokes it directly into the mold for color mixing, and then pours in the transparent drop glue.

7. When it is about a centimeter high from the top of the mold, stop pouring the glue and let it stand for at least 6 hours.

8. The previous flowers and glue are already in a very viscous state, gently cut off the flower stem that is higher than the mold, and then put in the stone after adjusting the glue and stir it slightly and let it stand together.

9. After standing still, take out one grain by one with tweezers, and put the black and white into the mold separately.

10. Poke a little bit of color essence (blue, white and red) with a toothpick, stir them into the mold respectively, and make a circle of white, and the blue and red correspond to the previous color.

11. Then add the stone and add glue to the liquid level to protrude a little bit from the mold, and then wait for 18 hours.