How do I set up my router? Make 3M Telecom Broadband on four computers?

There are several possibilities:1The network cable is loose and the contact is not good.

2.Router settings problem, open a browser, type Yes router may be. Look at the router, the password is admin, follow the steps to set it.

3.There may also be a conflict between the IP of the computer when it is opened, and the IP of the computer is set to it.

See if the router settings are normal (how to read the manual).

To see that the connection is normal, it is to see if the light can be on all the time.

See if the three lights of the ADSL modem are on.

Plug in the admin password admin

Follow the steps to come.

For a moment, enter your router model and find one.

Hello, it is recommended to set it up as follows:

1.To connect the network cable to the router, first set the IP of the computer's wired connection to , open the browser and enter (some are, the computer IP is set to enter the user name: admin password admin

2.Find a setup wizard in the router, step by step, select the PPPoe dial-up method, and set up the Internet account and Internet password, 3If you need to set the wireless password, you can set the corresponding settings here, but finally set the encryption method to WPA2, because the password of the WEP encryption method is easy to crack, and it doesn't matter if you don't need it.

4.Confirm whether the DHCP service in the router is turned on, so that the computer can automatically obtain the IP address, I hope my answer will be helpful to you, more questions can be logged in to Hubei 10000 to know!

The IP on the computer can be obtained automatically, the router needs to be set up, but there are instructions for use, and when you buy it, the boss should tell you.

You can also use the router as a switch without setting a route. The cable that connects to the network is not plugged into the wan, but in one of 1, 2, 3, 4, and then 3 computers are plugged into the other 3 holes. That's how our dormitory is used.

If you want to add machines in the future, you'll have to think of something else.

However, it is also possible that the telecom company restricts the number of Internet access. After all, I only paid one money, but I used so many machines. Telcos will definitely restrict.

I have a two-megabit network speed with 11 computers, and the general computer maintenance personnel will set it, if you buy a router from him, he will usually set it up for you for free, but I bring 11 computers and use a switch. I'm all set up to get the IP address automatically. The three that you said will drop the line together may be the ghost of the telecommunications bureau, because they have recently blocked the route, which means that a ** line can only carry 2 computers at most.

But I don't seem to have the situation you mentioned here, it turns out that one night, two computers in my house can't access the Internet at the same time, if two at the same time, both computers will be disconnected at the same time. But that hasn't happened anymore.

If the local telecom allows multiple computers to share a single IP, then it is possible to view the routing interface and the network card of the computer that was disconnected. But this may not be the case.

If the telecom limit is up to two computers, then you can change the route that can break the block, just according to your settings, and it should be fine.

Didn't you let them set up the router when you bought it.

The IP of the computer is set to be obtained automatically.

If it doesn't work, the third computer will be modeled after the settings of the first two, and the last one will be changed to 003, as long as it does not conflict with the previous two, the problem is not big.

What does that one mean?

Hello: You first connect the device as shown below.

Enter the address you see on the router in your browser, which is usually.

Then enter,Enter the corresponding account and password,Generally, the newly bought admin is indeed the operation interface,You will see a setup wizard on the left,Enter the setup wizard interface。

Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

Then connect another computer to the router.

I don't understand the title, does it mean that Lu You uses Lu You to access the Internet on two computers? If you already have a cat at home,It depends on what your land by IP is,If it is,Enter that IP on IE and then it will run out of a window to enter the default account password admin,Enter the land by the settings in the selection,Setup wizard and then the next one,Select the first PPPoe option and then the next step,Enter your broadband account and password,It's done,Then it's on the land and then connect another network cable out,You can access the Internet on two or more units,If you have a wireless network card, you don't need a network cable. By the way, you have to set the IP on your computer to get it automatically, and it's OK to pull.

According to the relevant regulations of the Ministry of Public Security on protecting Internet security: one account, one terminal! When there are multiple terminals for one account:

The relevant certificates of the relevant end users must be issued, and the registration must be carried out in strict accordance with the record; In order for the network security department to monitor, supervise, supervise and monitor the network security; Prevent the use of the Internet to carry out sabotage activities on the Internet! Fight against the use of the Internet for criminal activities at any time! Copyright Notice:

This answer is original to "Harmony" and must not be stolen by anyone! At the technical level: using other technical measures such as routers, dual network cards and network switches, one account can be connected to the Internet with multiple machines, and there is absolutely no technical problem; For the security of the Internet, we still need to be law-abiding citizens and surf the Internet reasonably, reasonably and legally; Contribute to the maintenance of a harmonious society!

Operators use network monitoring software to implement real-time detection in accordance with the law; And take corresponding (page notification, forced removal of stitches, restrictions, etc.) to implement alarm measures for users in accordance with the law, and require users to go through the corresponding (one terminal and one account) procedures; Multiple terminals for one account must go through the corresponding procedures in accordance with the law and be carefully recorded. When you access the Internet through multiple devices of the router, you find that only one terminal can access the Internet, and the other terminals cannot access the Internet, you may be restricted by the operator. For details, please consult your local operator, okay?

Buy a separate head on the network cable connected to the computer (the one that connects the router to the computer), plugging one end into this computer and the other end into that computer.

Telecom Broadband Connection Router Method:

1. First of all, you need to connect the telecom optical modem, wireless router, and computer with network cables, and the correct connection method

1) Connect the LAN port on the telecom optical modem to the WAN port (Internet port) of the router with a network cable.

2) Connect your home computer to any LAN port in the router with a network cable.

1) Open the Control Panel.

2) Select Network & Sharing Center.

3) Select Change adapter settings.

4) Select Ethernet (local connection) and right-click.

5) Click Properties.

6) Double-click the IPv4 protocol.

7) Enter the corresponding information and click OK.

3. Set up a router to surf the Internet.

1) There is a sticker at the bottom of the router, in this sticker, it is recommended to view the management address (login address) of your router

3) The router will automatically detect the Internet access mode of your home broadband, wait for a few seconds, and set the Internet access parameters according to the detection result.

Note: If the Internet access method is detected: PPPoe dial-up, the system will prompt you to fill in the broadband account (Internet user name) and broadband password (Internet password) of your home broadband in the page.

If the system detects that the Internet access method is: dynamic IP Internet access (automatically obtaining IP address), the page for setting Internet access parameters will not appear, and it will jump directly to the interface of setting WiFi name and password.

4. Then set your router's wifi name and wifi password (wireless name, wireless password).

5. Set the management password of the router according to the prompts on the page.

6. Finally, according to the prompt information on the router settings page, end the router settings.

The installation and setup of the router is as follows:

1.First, connect the line between the broadband modem and the computer of the router, and use a network cable to connect the LAN port of the broadband modem to the WAN port of the router.

2.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

3.After logging in to the background, select Quick Settings, enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

4.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

5.Confirm it once the input is complete, and then restart the router to take effect.

Router Setup Tutorial

Home Network Environment Cabling]:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- a computer.

2. No telecom cat: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. Check your IP first, method: win+r--- enter: cmd--- enter in the black and white interface: ipconfig, press enter.

4. The router login interface pops up, enter the default login username of the router: admin and password: admin (if it is incorrect, look at the back of the router).

5. The above methods do not work, in the reset router. The address, account number, and password are all on the back of the router.

Set Router Dialing]:

The IP and DNS settings of the computer are automatically obtained.

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL dialing), follow the prompts to enter your Internet username and password, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

3. If you want to use wireless wifi, your router must have a wireless routing function, in the settings, turn on the wireless routing function, here, the wireless signal signal is changed to one of them. The strongest anti-interference.

You can also set a password for your Wi-Fi connection.

1.First of all, you need to connect the telecom optical modem, wireless router, and computer with network cables, and the correct connection method: (1) Put the network port on the optical modem.

Here's how to set up a telecom broadband connection:

1. First of all, go to the relevant business outlets to apply for the installation of broadband, and wait for the master to come to install. They will help you install your home gateway and import your internet information.

2. Next, connect the home gateway and router with a network cable, power on, and wait for them to turn on.

4. Follow the steps shown in the diagram > Set up the login password > Set up the wizard > Enter the account password > Follow the prompts >> Restart when everything is done.

5. Try to connect to the wifi you created, this is like connecting a hotspot on your mobile phone, and the connection may not be successful.

6. If you can't connect to the network, log in to the home gateway**2, check the network status, and follow the prompts to patch. Just be patient.

Common broadband errors** and how to resolve them.

1. Error **691

Solution: If the same 691 prompt still appears, it may be caused by the arrears of the Internet account or the hanging of the account, you can call China Telecom customer service **10000 to inquire or report the obstacle.

2. Error **678

Solution: If you encounter an error message of 678 during the Internet access, you can check and deal with it step by step by following the following steps.

1. First, check the modem status and determine whether the modem is normal.

2. Under normal circumstances, restart the computer after powering off the modem for 5 minutes. If the modem is abnormal, power off the modem and check whether the network cables between the modem and the NIC and between the modem and the splitter are connected.

3. When restarting the modem is invalid and the modem light is normal, it is recommended to uninstall the NIC driver and dial-up software, and reinstall it.

4. Still prompt 678, please call China Telecom customer service **10000 to report the fault, we will send someone to check whether there is a problem with the line for you.

3. Error **769

Solution: 769 failures generally occur in the XP operating system, which is due to the local connection disabled in the computer. All you need to do is restart your local connection and you'll be back to normal. First, find a "Neighbors" icon on your computer's desktop.

Next, you can directly right-click the online neighbor with the mouse, then click the property with the left mouse button and double-click the local connection, and the system will automatically enable the local connection. When the local connection is activated, re-dial to access the Internet.