I m a new car, and I ran more than 80 miles in third gear, okay?

Hello, try to avoid new cars, low-speed high-speed, high-end low-speed, [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, no, 80 yards must be in 5th gear. Thank you for supporting Auto Master. Hope mine is helpful to you. I wish you a happy life! [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello, of course, this kind of operation is not good, the speed of eighty miles should be more than four gears to be more appropriate, the speed of the third gear will be very good, and the engine wear and tear will be accelerated for a long time. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello, no problem, I wish you a pleasant use of the car [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello. There is no problem [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, it's better not to be like this at least 4th gear [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello has no effect. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello, try not to damage the engine like this [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

High rpm is not good for the car [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

This will cause a little damage to the car. Driving at low and high speeds increases engine speed, which can exacerbate engine wear. If the speed is 80 km h, you can use the highest forward gear and the engine speed is relatively low.

When driving a car with a manual transmission, the gears must match the engine speed and travel speed.

Most cars have a relatively economical speed range. While driving, the rider can keep the engine in this speed range all the time. If the speed is high, it will upshift, and if the speed is low, it will downshift.

Every time you change gears, you need to press the clutch pedal quickly to the end, otherwise you will not be able to change gears smoothly.

You also need to use the clutch when you start, and you need to use semi-linkage skills when you start.

In the beginning, the difference in quick-selling coincidence between the flywheel and the clutch plate was too large. If the clutch is engaged at this point, it will cause the engine to stall.

The use of semi-linkage technology at the start can gradually reduce the speed difference between the engine flywheel and the clutch plate, so that the car can start smoothly.

When using semi-linkage technology, it is important to control the time. If the clutch remains in a semi-synchronized state for a long time, it will accelerate the wear rate of the clutch plates, and even directly burn out the clutch plates.

As mileage increases, the clutch plates wear out, so the rider needs to replace the clutch plates.

It doesn't matter if you happen once in a while, don't tell it for a long time, otherwise it will have the following effects:

1.Fuel consumption: When the vehicle is driving at low speed and high speed, the faster the speed, the higher the speed required by the engine, and the fuel consumption will naturally increase at this time.

2.Impact on the gearbox: After the vehicle increases the speed, it has a forward traction force, which will drive the gears of the gearbox under the action of this traction, thereby driving the engine to run at high speed.

In this process, if the forward traction of the vehicle is larger, and the engine speed does not reach a certain value, the engine will give the gearbox a counter-impulse force, resulting in wear and damage to the gearbox, if the vehicle is under load, it is serious and easy to cause the engine to burst the cylinder. This situation is the same as the principle of using the engine to decelerate by downshifting when the brakes fail.

3.It is easy to illuminate carbon deposits: In the process of resisting high-speed driving, because the speed of the engine is accelerated, the piston movement speed in the engine is accelerated, which is easy to lead to insufficient combustion of gasoline in the cylinder, resulting in a large amount of carbon deposits.

For the current car engine, it is basically a high-speed engine, and the maximum output is about 3000 rpm, so there should be no big problem in general, but fuel consumption will definitely rise.

Preferably in 4th gear.

1.3 gears open 80 high fuel consumption.

2.If the engine revs too fast, the engine may overheat and torque too much, which is not good for the engine and transmission. Generally, it is best to control the speed of 60 yards at 2000, 2000 or more than 60 yards, and 3000 on the highway, it is best not to pass 4000 for a long time, which is not good for the engine.

When the car is in 3rd gear, the suitable speed is 30 to 50 miles, if the speed reaches 80 miles, it will have the following effects on the car:

2. The engine speed is too fast, which will cause the engine to overheat, and the low-speed and high-speed will make the fast work of the reed machine reach high speed, and the damage to the engine will be greater.