How do you knit handmade woolen shoes? How to knit woolen shoes by hand

Tools Raw materials: wool thread, wool needle.

1. Prepare the yarn and knitting needle. Take 6 stitches to do a knitting demonstration, as shown in the figure below.

2. Start knitting the needle, and add a needle to the winding when there is still the last needle left. Then after weaving the last stitch, turn it over, continue to knit the next stitch, knit until there is still the last stitch left, and then wind the thread and add another stitch, as shown in the figure below.

3. Knit repeatedly until 10 stitches are added to the needle, as shown in the figure below.

4. Then knit the needle without adding or subtracting, and start to reduce the needle from the heel to the toe, as shown in the figure below.

5. The needle reduction method, the last 2 needles in each row and one needle, as shown in the figure below.

6. It is good to reduce to the needle and there are 6 stitches, these 6 stitches are used as the toe cap, and the sole is completed, as shown in the figure below.

7. Use a needle to pick 1 needle in each hole on both sides of the toe cap, pick it on 2 needles respectively, and start to knit the needle, as shown in the figure below.

8. When knitting to the left and right sides of the toe cap, there are 2 needles and one knitting needle, as shown in the figure below.

9. Weave it to the height of the upper in this way, as shown in the figure below.

10. After the upper is woven, start to weave the shoe tube, knit a needle, and then knit a needle, as shown in the figure below.

11. Weave to the required height, 5 and then close the needle and break the thread, hide the thread, and the woolen shoes will be knitted, as shown in the figure below.

1. We need to weave shoes from 3 parts. the first part of the sole; The second part is the upper, and the third part is the tube. Prepare the rod needle and rod needle thread. Start knitting the soles. Let's start with 4 needles and we'll do the demonstration.

2. Then start to add the needle, and add the last shot after the first needle. Then turn over the surface to knit the needle back. At this point, there are 6 coils on the rod pin.

3. Next, add a needle to the head and tail again, and then return without adding or subtracting the next needle. At this point, there are 8 coils on the rod pin. Then knit the needle on both sides without adding or subtracting, and weave it to the required length.

Then start to subtract the needle, as with the additional needle, after the first needle, before the last needle, 2 needles and one needle.

4. There are 4 more needles on the stick needle, and these 4 needles are used as the toe cap. The sole is knitted.

5. Then start knitting the second part of the upper. Use a stick needle to pick out one stitch from each of the other 3 sides and start knitting the needle. Every time you knit to the left and right sides of the toe cap, you have to reduce the stitch, that is, you have to have 2 stitches and one stitch.

6. Repeat the weaving to the height required by the upper. So that the upper is knitted. The next step is to weave the shoe tubes.

7. To knit the shoe tube, change the stitching method of knitting, and start to knit a needle under the needle and a needle on the needle. Weave to the desired length without adding or subtracting. Then close the needle. So that the shoe tube is knitted.

8. Then tidy it up and turn the shoe tube down. In this way, the knitting of the woolen shoes is complete.

1. Weaving slippers face: (using two colors of wool, red and yellow) 1. 6 needles from the red wool and weaving the first row; When turning back to weave the second row, the first stitch is not knitted, and a stitch is added before the last stitch, and the last stitch is knitted; Then go back and weave the third row, the first needle is not knitted, at this time, it is already 7 needles. 2. At the beginning of the fourth line, use yellow wool, tighten the red line a little, pull it to the back, and use the yellow line to cross the red line and start weaving.

The first stitch is removed directly and is not knitted; The second needle begins to weave the yellow thread, and when it reaches the penultimate needle, one more needle is added, and the last one is knitted; Then go back and weave the fifth row, and the first stitch is not knitted, at this time there are a total of 8 stitches. 3. At the beginning of the sixth line, first pull the yellow line to the back, press (cross) with the red line and start weaving the sixth line, the method is the same as above.

4. Repeat this and weave it to about 54 stitches (you can use the sole to measure the edge of the needle, tighten it a little, and measure half of the sole - the midline is separated, and only half of the edge is measured.) ), starting with the front toe part of the shuttle shoe. Take the yellow line as an example.

The first row of yellow thread is woven in the past, and the last 4 stitches are not woven in the rest, and the red thread is woven in the past, and the red thread is woven in the past (so that the front is flat, not pointed.) Then go back to weave until there are 4 needles left from the yellow thread just now, change the yellow thread to weave, so that 8 small pieces of shuttle (5 needles each, a total of 40 needles), the remaining source of more than 10 needles without hail and lack of weaving, remember to change the thread with the same pretence, weave three back and forth (that is, yellow-red-yellow, the middle is facing red).

First of all, start with 10 stitches for size 38-39 shoes, add 5 stitches for each color knitted, and continue until the end of 35 stitches.

Weave back and forth 30 circles, this color back and forth 15 rows of weaving the first needle, the second needle plus a needle, knitting to the last 2 needles when the left 2 needles with a needle to pick out 2 needles not to weave.

The latter is to add a needle when weaving the second needle, and the last two needles are not knitted, and only 12 needles are left in the end. Knit all the 12 needles and the 46 needles you just picked out, and then weave the thread of another color.

Okay, now the weaving flowers, first knit 9 stitches and then pick one stitch not to weave. Knit three more needles, and pick a piece of talk about the needle is not weaving, has been repeating 11 needles do not weave the past, only the back 8 needles are left, and the reverse weaving is also like that, pick the past 11 single needles are still like that pick the past not to weave, and the rest are all woven under the needle.

Change the thread, weave out 11 needles to pick 1 needle not to weave the same as the previous line, but the previous line can now be knitted, and then knit three needles, and pick a needle not to weave, has been repeated 10 needles do not weave past, only the back 10 needles are left, and vice versa, just picked out or not knitted, directly pick over.

Change the thread, the same as the first row of pick weaving, first weave 9 needles and then pick a group to lift a needle without weaving. Knit three more needles, and pick a needle not to weave, has been repeated 11 needles do not weave the past, only the back 8 needles are left, in turn weaving is also like that, pick the past 11 single needles are still like that pick the past not to weave, the rest of all the knitting needles, to the first pick of the needle.

Switch threads and weave back and forth, and then start picking. Change the thread to weave a back and forth, pick out 12 knitting back and forth, the second row of weaving to the left needle on the pick 2 needles, weaving back is the last second or third needle and into a needle, just like the left pick 2 knitting, the right last two or three needles and a needle, has been weaving like this, and finally knitted 35 needles. 35 stitches have been knitting 30 back and forth, and then combined, you see I combined the blue 5 stitches, press the beginning of the knitting piece, knit whatever color and finish all the color.

Then go to the bottom, start work after the bottom, stitch the woolen upper and the sole, first turn the woven woolen upper over, and how to wrap the upper around the mouth down. The middle of both ends should be sewn with thread, so that the yarn is fixed, and the sewing will not be crooked.

The knitting method of woolen shoes is as follows:

1. Tie the yarn into a slipknot, thread the rod needle into the slipknot, and wrap the needle with your fingers. Take 6 stitches to do a knitting demonstration.

2. Then start to knit the sole part, start to add needles, knit a needle, and then wrap the thread on the rod needle, so that a needle is added.

3. When this row is woven to the last stitch, the needle is also wound on the rod needle.

4. Then weave the needle back to return. Repeat the weaving in this way, adding the needle to the 12 coils on the rod needle.

5. Then start to weave the needle on the front and back without adding or subtracting, and weave it to the length of the foot.

6. Start to collect the needle, after knitting a needle, two needles and one needle to collect the needle, when weaving to the last 3 needles, two needles and one needle to close the needle, and the last knitting needle.

7. Then weave the needle in reverse. Repeat this until there are 6 stitches in the rod. The sole weave is finished.

8. Use these six needles as the toe cap, and pick up the other three sides with two stick needles.

9. Start knitting and tie it, and when weaving to the toe cap, collect a needle on the left and right sides. Always keep the 6 stitches on the toe cap.

10. After weaving to the height of the required upper, start weaving the edge of the shoe.

11. On the top of the shoes, knit with a needle and a needle to the height you like.

12. After the completion of the weaving of the shoe edge, the needle is closed, and the needle is knitted on the needle, knitted on the needle, and the needle is wound from behind the rod needle.

13. After all the needles are collected, tidy them up, and finally sew them into a small flower, so that the weaving of the woolen shoes pattern is completed.

Wool usually refers to yarn spun from wool, and also refers to threads spun from different types of chemical fiber materials, such as: acrylic fiber, polyester fiber, persian fiber and so on. According to the people of Lanzhou, the capital of Gansu Province, the ancient silk city

Wool means disdain and contempt. It can also be used for the depth of brotherly love, commonly known as "inserting a knife in the ribs of a brother and inserting a brother twice in a woman" is not at all between brothers who are casually called "wool".

Crochet method of woolen slippers

Step 1: Hook shoes should be selected with a good bottom, I bought a good line, or I can put it on my own. I figured it conveniently and the price was about the same, so I chose it.

Step 2: I use a short needle to hook the sole of the shoe, which is one circle smaller than the sole. After the hook is done, a circle of short needles is hooked around, and the number of needles is determined by the upper line of the sole.

Step 3: Place the bottom surface on the sole. The number of needles should be evenly distributed. Because this will affect whether the upper looks good or not.

Step 4: Hook two short needles at the junction between the edge of the sole surface and the center.

Step 5: The upper can be hooked below. First, the toe hook six to seven groups of medium and long needles or long needles (two needles in each group), and leave a certain length of thread on the left side to close the needle.

Step 6: Four or five rows of toe toe heads, each row of starting and closing needles should be close to the previous row, and one needle is separated from each row of starting and closing needles in the back.

Step 7: Hook until the end. I sample the diagram.

There are thousands of ways to knit woolen shoes, whether you want them for adults or children, men or women.

Red wool from 6 knitting first row, back to knit the second line when the first needle is not knitted, the last needle before the addition of a needle and then knit the last needle, and then back to weave the third row, the first needle is not knitted, at this time it is already 7 needles.

1. 4 needles from the first step.

2. Start to knit the needle on the front and back, and add a needle in front of the last needle. The method of adding needles is to wind the thread from top to bottom, and the thread wound is a needle.

3. In this way, add one needle before the last needle in each row, and add 12 coils to the rod needle.

4. Do not add or subtract the front and back of the needle. Weave to the desired length.

5. Then start to reduce the needle, and the needle is reduced in the last 2 needles of each row and one needle. There are 4 more stitches on the stick needle, and these 4 stitches are used as toe caps. So that the soles are knitted.

6. Thread the other sides with a rod needle.

7. Each row is woven to the left and right sides of the toe cap by one stitch. It's 2 stitches and 1 stitch.

8. Continue to reduce the needle to the height of the upper you need.

9. Shoe tube weaving with a needle on the needle and a needle on the needle. Weave to the desired height.

10. Start to collect the needle and finish the coils on the rod needle.

11. In this way, the woolen shoes are knitted.

Ingredients: Spoke No. 4, Hook No. 3 scissors.

1.Start with 10 stitches.

2.Weave 16 rows, and measure the square in 6 times 6 with a ruler.

3.Continue to knit 19 stitches.

4.Loop, knitted 16 rows - 6 cm.

5.Continue to knit 9 more stitches on the other side.

6.Collect 9 stitches on one side.

7.Knit 16 rows as in the same steps before synchronization, 6 cm long. Then take all the rest and start attaching the slippers.

8.Hook out the lace seams with pale wool.

9.Twist the needle around the corner and continue, then fold the slippers.

10.Three-dimensional effect.

1. Look at the different thread thicknesses, the number of needles is slightly different, I started 16 needles, and the general wool thickness. In order to prevent it from being too loose, look for a thinner rod needle, as long as the woven upper is not so hard and not soft, it is suitable.

2. The second line begins to add needles (one back and forth counts two rows), and I posted a picture of the position of the needle, that is, when there is still one needle left on the far left of each row, add a set of needles.

3. After the upper is enough for the width of the shoes you usually wear, you will start to add no needles.

5. After weaving two layers of uppers, you'd better find some cloth, clip it in the middle of the upper, and sew it, so that the upper of the woolen yarn is not easy to get out of shape. Also, because the side of the line change just now has already reached the mezzanine, your feet will not hook those lines.

6. After getting the upper and then look at the sole, the pattern is the same, you just knit it according to the size of the sole, which is slightly smaller than the sole you bought, because the wool is an easy stretching thing. When stitching, you'd better add something under the sole. This makes it easier to keep warm.

Needle position (one needle at the outermost point of each round-trip).

1. First sew the bought soles and woven soles (you can use the needle of the general hand sewing clothes, or you can use the tools that look like changing the taper), if the woven sole is not thick enough, you can also add elastic wadding or the like, a thicker such as fragmented tweed materials are also made, as long as you have a way to fix them on the purchased soles.

2. The upper does not need to be mixed with the purchased sole, you only need to sew the sole you knit with the upper, and simply sew it with the needle of the general sweater.

Simpler infant woolen shoes knitting tutorials, all basic needles, lazy people can also learn.