What should I do if the VGA line signal is interfered with?

Updated on technology 2024-08-05
12 answers
  1. Anonymous users2024-02-15

    The main reason is that the line is too long, which makes it susceptible to interference and the signal attenuation is serious. You can change to a shorter and interference-resistant VGA cable. If you don't change the wire, you can also wrap a thin layer of iron sheet or several layers of metal foil on the surface to prevent interference.

  2. Anonymous users2024-02-14

    1: Use a VGA extension amplifier. The project I did was in the generator room, 100 meters, no problem.

    2: Carry out casing, VGA line - PVC pipe - steel pipe, this way, subway weak current installation is this way.

    3: Eliminate interference, and the VGA line runs from somewhere else.

    The above is my experience in engineering installation!

  3. Anonymous users2024-02-13

    Interference, change the *** line, with a VGA extender.

  4. Anonymous users2024-02-12

    If the computer needs to use three plugs with ground wires, it must be grounded, otherwise it can't be shielded, and if the connector is loose, the pins will be tinned and coated with a drop of solder paste, not too much, and the air gun will melt.

  5. Anonymous users2024-02-11

    VGA's line anti-interference ability is not strong, the line length generally does not exceed 15 meters, and the line greater than 5 meters should try to choose the best wire, otherwise the display quality will be affected under some conditions.

    To put it simply, don't be greedy for cheap and buy cheap threads, and there will be a chance that the screen will be full of snowflakes when the time comes.

  6. Anonymous users2024-02-10

    Why do you need a VGA cable,42Inch TV was bought several years ago,No HDMI interface?

    Even the DVI interface is much better than the VGA.

  7. Anonymous users2024-02-09

    The effective distance of the VGA cable is generally 20 meters, and it is recommended to buy the best one.

  8. Anonymous users2024-02-08

    The VGA crossover divides the same frequency to different display devices, and it can only accept one working frequency, otherwise it will be subject to mutual interference.

    Method 1: Adjust the refresh rate of the monitor and the refresh rate of the LCD at the same time: 60Hz(Provided with: no TV).

    Method 2: Only one display device is ensured. Trap this.

    This Wang Xun is a little suggestion from me, you can try it!

  9. Anonymous users2024-02-07

    Solution: Check the image first: unplug a cable with serious interference from the main unit, and use a monitor (or TV) to directly view the image.

    That is, the camera - the transmission cable - the monitor, to see if there is any interference? If the monitor power supply is 2 plugs, do not touch the ground, and do not touch other grounding objects.

    1.There is interference - check the front-end camera output again for interference? If not, it means that the interference is from line coupling, which is true interference; If there is interference in the front-end camera output,—— camera or power supply failure, troubleshoot - this is false interference;

    2.If you look at the lack of interference with a stand-alone monitor, there is no interference from the camera output and no interference from the line. But when you get to the host, there is interference on this way - it must be false interference, most of it is ground loop interference introduced by "multi-point grounding" - the correct design is:

    The system can only be connected to the ground at one point, and all cameras and power sources at the front end should be insulated from the ground. There is no need for anti-jammers or changes in the transmission mode, it is solved, and more importantly, the "potential safety hazards" are eliminated;

    3.The real interference introduced by the line is generally not particularly powerful, and the image can be seen clearly, which can be effectively solved with an anti-jammer; If the interference is severe, the image can hardly be seen clearly, and it is mostly false interference.

  10. Anonymous users2024-02-06

    1. For the problem of closed routes, re-joint.

    2、The problem of TV's anti-interference ability,You can only turn off the computer and watch TV again。

    3. Problems with VGA cables. Try wrapping the VGA cable in aluminum foil.

    4. Try to change the direction of the line. Try not to guess the waiting.

    5. There is a problem with the high-frequency head of the TV itself6The mode of the computer is different from the mode of the TV, and the mode can be converted with the remote control, 7The VGA outlet of the computer is connected to a splitter, and a better VGA cable is used to disturb 8Problems with your computer's graphics card.

  11. Anonymous users2024-02-05

    Cable TV ground string a non-polarized capacitor to try.

  12. Anonymous users2024-02-04

    It could be a problem with the graphics card mismatch.

Related questions
8 answers2024-08-05

One way to make a joke: power off or airplane mode.

Hahahaha, this method is not very feasible, after all, many things still need to be contacted by mobile phone. >>>More

13 answers2024-08-05

There are four main reasons for this:

The first main reason: that is, the connection data cable between the computer host and the LCD screen is off or the connection cable is damaged, a black screen will appear, and the detection signal line will be displayed, you can dial the connection cable back up and plug it in, and then turn it on again, you know, if it is normal, it is this connection that falls off. If the problem persists, see the reasons below. >>>More

6 answers2024-08-05

Let's see for yourself,!Find a place with a signal. Wish.

17 answers2024-08-05

Hello, if you are a Beijing Mobile customer, it is recommended that you take a look at the surrounding customer network, if the surrounding customer network is not good, you can call 10086 for feedback. If there is no problem with the network situation of the surrounding users, then there may be a problem with the settings on your mobile phone, and it is recommended that you troubleshoot as follows: >>>More

15 answers2024-08-05

The solution to a particularly poor mobile phone signal is to turn on airplane mode. >>>More