What should I do if I enter the wrong filter key password when I boot up?

The shift key is stuck, and a few more clicks will see if it bounces back.

It may be that the keyboard is sticky, so it is recommended to try a different keyboard.

I don't understand. If it's a desktop, just use the keypad.

If it's this, press the fn+numlk key combination, switch the keyboard to the keypad, the responsive keys have numeric identifiers, and enter your password.

If that doesn't work, you can try this again:

Restart the computer, when you boot to the system login interface, hold down the Ctrl+Alt key at the same time, and then click the del key twice, a new login interface will appear, enter the "administrator" password at the user name is empty, press enter to log in, after logging in, open the control panel and select User Account Change Account Click on the original "Account Name" Change my password Enter the new password, enter the new password again, and then click the "Change Password" button.

1.Restart the computer, press the F8 key after booting it and not move until the advanced options screen appears, then release your hand and select "Safe Mode of Command Prompt" to press Enter.

2. At the end of the running process, the system lists the selection menu of the system superuser "administrator" and the local user "**", and clicks "administrator" to enter the command line mode.

3. Type the command: "netuser."

add" to force the password of the user to be changed to "123456". If you want to add a new user here (e.g., username abcdef, password 123456), type "net."

userabcdef

add", after adding, you can use "net

localgroup

administrators

abcdef

add" command promotes the user to the user of the system administration group administrators and gives it super privileges.

4. Restart the computer, select Normal mode to run, and you can log in to the ** user with the changed password "123456".

Copy, you try it.

After logging in, you can right-click on My Computer, click on Manage, click on Local Users and Groups, click on Users to see all users on the computer, double-click on one of the usernames, you can see the attributes of that username and then you can change the attributes, click Apply, OK.

Click on a group to see all the groups, or you can double-click to view and change their properties.

Let's see if it's a keyboard problem. Try a different keyboard.

Plug your keyboard under the connector on the back of the case. Check your BIOS settings, the easy way is to put a charge on the CMOS battery. If it still doesn't work, try it with the keyboard of the PS2 interface, it can be used, check your system device, go to the device manager to see if your U-port keyboard is banned or you haven't found the hardware It's always plugged in the back of the case, and the light will be on when you just turn it on.

But when it's time to enter the password, it doesn't light up. This should be a problem with the BIOS settings, reboot and keep pressing Delete(del) or F2 or F12, then press F9, Y, Enter, F10, Enter, the computer will automatically restart, restore the BIOS default value to try.

1. First of all, we click on the "Start Menu", and click on the "Settings" icon in the Start Menu, as shown in the figure below;

2. Open the Windows Settings interface, find "Update & Security" and click to enter;

3. After turning on Update & Security, click the "Restart Now" button on the left side of "Recover" on the left side.

4. The system automatically enters the security operation interface and selects "Troubleshooting";

5. Click "Advanced Options", as shown in the figure below;

6. Click "Startup Settings" in the interface of advanced options;

7. Click the "Restart" button in the interface of the startup settings;

8. After restarting, press [F4] or 4 on the pop-up startup setting interface to enter "Safe Mode", so that you can log in normally;

9. Enter the system and press win+r to open and run, enter: "msconfig" command and click OK to open the system configuration;

10. Click [Normal Start] in the general options of system configuration and then click OK, and after restarting the computer, the win10 boot password input box can be displayed!

, about ten seconds. The Settings dialog box for setting the filter key appears. Set it up inside and you're good to go.

If it doesn't work. You can try to hold down the left shift for about ten seconds. Reinstalling the system will definitely solve the problem, but it's not necessary.

Or there may be that you have a bad keyboard. It's also possible that the shift key is stuck.

You keep holding down the shift key on the right side of the keyboard for about ten seconds or so. The Settings dialog box for setting the filter key appears. Set it up inside and you're good to go.

If it doesn't work. You can try to hold down the left shift for about ten seconds. Reinstalling the system will definitely solve the problem, but it's not necessary.

Or there may be that you have a bad keyboard. It's also possible that the shift key is stuck.

, about ten seconds. The Settings dialog box for setting the filter key appears. Set it up inside and you're good to go.

If it doesn't work. You can try to hold down the left shift for about ten seconds. Reinstalling the system will definitely solve the problem, but it's not necessary.

Or there may be that you have a bad keyboard. It's also possible that the shift key is stuck.

Need to use a USB flash drive PE or CD to crack the password:

1. After entering PE, open the software through "Program - System Maintenance - Windows User Password Modification". 2. The software will automatically locate the SAM file and click "Open".

3. After clicking "Open", the following interface appears, listing the system users.

4. Select "administrator", if you need to hack other users, select other users.

5. Click Change Password, and the following interface appears. If you need to reset your password, enter a new password in the input box. If you need to clear the password, click OK directly.

6. Click OK, and then click Save Changes. The password was cracked.

What kind of computer are you?

If you have a desktop, you may not press the numlock key on the numpad, you can see if the light is on.

It's possible that there is a problem with your shift key.

Press the fn+numlk key to have a light that is on or off, if you want to enter the keypad, it needs to be on, otherwise it is not on.

Pay attention to whether the numbers are capitalized and the keypad is locked.

The shift key is stuck, and a few more clicks will see if it bounces back.

Press the del key when the power is turned on.

advancedbios

boot - numlock status to on is fine.

This is the keyboard light switch under the BIOS.

This is generally not possible. It could be that you forgot your password.

1。Power on and press F8 to enter safe mode. If the administrator account does not have a password, use an empty password to change it back to the original password.

2。If the administrator user has set a password and forgot it. Just use a small program that you bought outside the system disk and has a clear system password inside. Just clear it.