-
1. If it is a one-button start installed after installation, including whether it is installed from 4S, the failure of the directional lock is artificial, otherwise it is impossible to drive.
2. If it is the original one-button start, this is the fault of the directional electronic lock.
-
It's just that there is no power, how long has the spare battery been left?
Directly call the car to come over and take the electricity, just a hand, but the main driver's one-key lifting will be invalid, you need to re-learn, operate according to the manual, start the car and hang up the reverse gear to see if the rear camera is hanging.
-
What to do if the steering column electronically unlocks the mountain.
-
Diagnosing electronic steering lock failure and queuing:
1) Check the steering gear, steering pump control valve, oil cup filter, steering oil, and clean the entire power steering system.
2) If the pump is dirty, be sure to clean the inside and outside of the booster pump and the oil pipe (cotton gauze or other multi-fiber cloth should not be used, clean with a clean brush), and exhaust air to the steering system according to the regulations.
3) Inflate the tires according to the regulations and adjust the performance of the engine.
5) Adjust the tension of the belt and tighten the connecting screws of each part according to the regulations.
6) Check the connection parts of the tubing and tighten the connecting bolts.
7) Replace the oil line, power steering pump, or power steering gear.
Electronic steering lock failures are usually due to the following reasons:
1) The inside of the oil cup is too dirty, the filter screen is blocked, or the oil level of the oil cup is low.
2) There is a lot of air in the power steering system.
3) There is a foreign object in the steering system, which causes the flow control valve of the steering pump to get stuck.
4) The tire pressure is insufficient, the steering column of the pump interferes, the connection is loose, the belt of the pump is loose, slipping or the pump installation position is loose.
5) The bolts of each connection part of the tubing are loose, resulting in the leakage of steering fluid.
6) The piston cylinder of the steering gear is worn too much, the oil seal is poorly sealed, and the control valve is bonded or damaged.
-
It is possible to contact the 4S store for processing.
Steering wheel locks are an effective anti-theft tool for cars. The steering wheel lock is generally composed of a lock handle, a lock seat and a lock lever, the lock seat and the lock shell are directly installed on the lock handle, one end of the lock handle is directly provided with a lock lever, and the side of the lock bar has a series of platforms on the vertical side, and the other side is the hypotenuse.
When using, the steering wheel is locked with a fork and hook, and it is stuck on the rim of the steering wheel of the car, so as to limit the rotation of the steering wheel, so as to achieve the anti-theft effect.
-
In this case, there is no way to start the electronic steering lock failure, because in this special institute now, it has an electronic steering lock lock block, which means that the steering wheel will be locked after the engine is turned off. This phenomenon may be caused by a problem with the circuit inside, or a problem with the motor inside. This specific word is that it needs to be disassembled, inspected, processed, and repaired.
-
How to deal with the failure of the electronic steering lock.
-
The failure of the electronic steering lock is that after you unlock it, Fang Tongshan Xiangzhu lock is not successfully unlocked in the local operation, or it is not quietly able to lock the car and cannot be successfully locked, so it is reported wrong, and you can go to 4S to overhaul it.
-
Summary. 1. The steering column lock motor works abnormally, and the steering column lock pin is driven by a motor, and the motor failure cannot drive the lock pin, and the lock fails.
Solution: Replace the brushes of the drive motor or replace the motor assembly.
2. The circuit of the steering column lock motor is broken, resulting in no current passing through the motor, which will be very troublesome.
Solution: First, use a multimeter to detect the location of the open circuit, and then connect the broken points.
3. The data of the electronic steering lock control unit is chaotic, resulting in the failure to output the signal or the output signal is wrong.
Solution: Replace the electronic steering lock control unit.
4. The insufficient battery of the vehicle causes no current to pass through the steering column lock motor.
Solution: Charge the vehicle battery or replace it with a new one.
How to solve the fault of the automotive electronic steering lock.
Hello, I am very happy to answer for you, the failure of the electronic steering lock will lead to the failure of the lock, the following are several common reasons for the failure of the electronic steering lock and solutions: 1. The steering column lock motor works abnormally, and the steering column lock pin is driven by a motor, and the motor failure cannot drive the lock pin, and the lock fails. Workaround:
Replace the brushes of the drive motor or replace the motor assembly. 2. The circuit of the steering column lock motor is broken, resulting in no current passing through the motor, which will be very troublesome. Workaround:
First, the location of the open circuit is detected with a multimeter, and then the open point is connected. 3. The data of the electronic steering lock control unit is chaotic, resulting in the failure to output the signal or the output signal is wrong. Workaround:
Replace the electronic steering lock control unit. 4. The insufficient battery of the vehicle causes no current to pass through the steering column lock motor. Workaround:
Charge your vehicle's battery or replace it with a new one.
Failure of the steering power assist does not ignite.
Baojun 510 electronic steering lock malfunction removed.
If the electronic steering lock fails to start the vehicle, first of all, you can adjust the tension of the belt and tighten the connecting screws of each component according to the regulations, check the connecting parts of the oil pipe, tighten the connecting bolts, and replace the oil pipe, power steering pump or power steering gear. If the above cannot solve the problem, it may be that the vehicle anti-theft system is faulty, or the steering column locking mechanism is faulty, and the trailer can only be towed to the 4S shop for inspection and maintenance.
-
Summary. Hello, I am happy to answer your car master exclusive technician to answer your car questions sincerely and sincerely for you, and find solutions and methods for you to ask questions. This problem occurs due to a malfunction in the communication between the electronic lock under the steering wheel and the PEP S of the body, or a problem caused by a damaged electronic lock.
You can lock the car with the remote control and wait for more than 10 minutes before trying again, if it still doesn't work, you can shake the steering wheel repeatedly, gently tap the steering column with your hand, and try to see if it can return to normal. Still doesn't work, you need to replace the electronic lock, I hope mine is helpful to you.
Hello, I have seen your inquiry, please wait for a moment and answer it for you immediately.
Hello, I am happy to answer your car master exclusive technician to answer your car questions sincerely and sincerely for you, and find solutions and methods for you to ask questions. This problem is caused by a malfunction in the communication between the electric remnant Lu Zhao lock under the steering wheel and the body of the body, or due to a damage to the electronic lock. You can lock the car with the remote control and wait for more than 10 minutes before trying again, if it still doesn't work, you can shake the steering wheel repeatedly, gently tap the steering column with your hand, and try to see if it can return to normal.
Still doesn't work, you need to replace the electronic lock, I hope mine is helpful to you.
-
Summary. Dear, the reasons for the failure of steering lock certification are: 1. The voltage of the car is low; 2. The steering column lock of the car is not opened; 3. The remote control key does not match the system; 4. The steering column lock cannot be unlocked or the steering column is faulty.
Pro, the reasons for the failure of steering lock authentication are: 1. The number of vertical lines of the car's electric surplus first voltage deviation is low; 2. The front pillar lock of the steering belt of the car is not opened; 3. The remote control key does not match the system; 4. The steering column lock cannot be unlocked or the steering column is faulty.
And it can't ignite, as soon as the door opens, the electronic lock fails.
The failure of the electronic steering lock will lead to the failure of the locking, and the following are several common reasons for the failure of the electronic steering lock and the solutions: 1. The steering column lock motor works abnormally, and the steering column lock lock pin is driven by a motor, and the motor failure cannot drive the lock pin, and the lock fails. Workaround:
Replace the brushes of the drive motor or replace the motor assembly. 2. The circuit of the steering column lock motor is broken, resulting in no current passing through the motor, which will be very troublesome. Workaround:
First of all, He Song uses a multimeter to detect the location of the open circuit, and then connects the broken points. 3. The data of the electronic steering lock control unit is chaotic, resulting in the inability to output the signal or the output signal is wrong. Workaround:
Replace the electronic steering lock control unit.
In this case, the direction is generally not fully returned when parking, and the electronic trillion branch lock fails to lock, and it is recommended to shake the steering wheel while starting the button to see if it can be started.
1.Be clear about your needs, your budget and the best results you expect; >>>More
Question: What is led display?
That's a good question. >>>More
A monitor is an IO device of a computer, i.e., an input and output device. A monitor is a device that displays an operation screen on a computer. >>>More
The reason why the car display screen suddenly went blank:1. The vehicle module fails. >>>More
Like desktop LCD displays, LCD screens rely on the backlight to irradiate liquid crystal molecules and transmit light, so the life of the LCD screen mainly depends on the backlight, not the liquid crystal molecules. When the screen is idle, it is better to turn off the LCD screen directly than to let the LCD screen protect the content. >>>More