What should I do if the washing machine can t drain How much does it cost to repair

You are the result of the poor working of the drain solenoid valve. This kind of washing machine does not have a drainage motor, there is only one solenoid valve, when draining, the main board gives the drainage instruction, and the solenoid valve is electrified to drive the drainage valve, and the water can be discharged smoothly. Just replace a solenoid valve of the same model, and the problem can be solved.

This kind of solenoid valve is not expensive, only more than 20 yuan a piece. It is generally sold in electrical and electronic components stores.

Washing machine poor drain elimination method.

When the washing machine does not drain well, you can find the cause from the following aspects and eliminate it:

1.At the corner of the rubber drain pipe connecting the washing machine bucket and the drain valve, dirt is deposited and the drain pipe passage is blocked, and the dirt in the pipe can be dredged as long as the dirt in the pipe is flushed out with clean water.

2.The drain screen at the bottom of the laundry bucket has accumulated too much dirt and blocked the flow holes. At this time, the dirt on the mesh screen of the drainage hole can be removed, and the flowing water hole can be dredged.

3.The tension spring on the discharge valve that controls the tightness of the tension belt loses its elasticity, and the drain can be fully opened. Adjustable short control strap allows the drain hole to be fully open.

4.Due to long-term use, or improper use, the drainage pipe is distorted and deformed and affects the drainage, and the pipe should be repaired or replaced with a new one.

Causes and countermeasures of poor drainage of washing machines.

The drain screen at the bottom of the laundry bucket has accumulated too much dirt, so the drainage is not smooth. The solution is: take out the drainage screen and wash it, and dredge the drainage hole.

At the corner of the rubber drain pipe connecting the laundry bucket and the drain valve, a lot of dirt is deposited, which blocks the inner diameter of the drain pipe, so the drainage is not smooth. The solution is: unclog the rubber drain pipe and flush out the dirt with clean water.

The tension spring on the drain valve that controls the tension of the belt loses its elasticity because of long-term use, and the rubber valve in the drain valve cannot be fully opened, and the drain hole is not large, so the drainage is not smooth. The solution is: adjust the control tension spring to make the drainage hole wider. There is no motor, so there is no need to change it.

Yours is a drum or a straight one, the drum has a drainage motor, if it is manual can be discharged, it should be straight, you can move it twice, it may be that the drain valve is stuck, and it should be possible to change one. 50 pieces should be able to get it, it won't be too expensive, give 70 at mostDon't give more, (if the valve is broken).

If the maintenance drum washing machine does not drain, it depends on the condition of the stool, if the drainage is caused by dirty blockages, then the maintenance of only jujube slag Bu will charge a door-to-door fee, generally 50 yuan. If parts need to be replaced. You need to charge a material fee plus a start-up fee plus a door fee, which is about 300 yuan.

The drainage problem of repairing washing machines varies from city to city, with different levels of engineers preparing rulers, and different levels of failure. In general, the cost will be lower if the drainage fault is smaller, and the cost will be higher if the drainage fault is large.

1.Clean the drain pipes.

If there is a problem with the drain pipe of the washing machine, it may be necessary to clean the drain pipe. The cost of this project is generally between 100 and 200 yuan, depending on the difficulty and length of the cleaning pipes.

2.Check the drain pump.

If the drain pump fails, it is necessary to check the fault point and then troubleshoot it. If you need to replace parts, it will cost about 200 yuan to 400 yuan. If the drain pump needs to be replaced, then the cost will be higher, about 300 yuan to 500 yuan.

3.Replace drains.

If there is a serious problem with the drain, then the entire drain may need to be replaced. The cost of this project is relatively high, and it may cost anywhere from 400 yuan to 600 yuan, depending on the length of the drainage pipe and the cost of the engineer's work.

4.Troubleshoot other issues.

If none of the above maintenance methods solve the problem, then some more advanced maintenance methods are needed. For example, replacing the dehydration motor, checking the circuit, troubleshooting, and so on. These repairs are generally costly, ranging from $500 to $1,000, depending on the severity of the failure.

In general, the cost of repairing the drainage problem of the washing machine is about 100 yuan to 1000 yuan. The exact cost also depends on the specific cause of the failure. When choosing a maintenance engineer, you must choose a professional and reliable one, and try to choose a service provider with a warranty to avoid problems such as low-cost maintenance and poor quality.

The washing machine can not drain the water so repaired:

1. Check whether the drain filter at the bottom right of the washing machine is blocked by fluff and dirt, and if it is blocked, it should be cleaned up. Rotate the filter in a counterclockwise direction and gently pull it out, remove the fluff and dirt, wash it with water, and then put it in place and tighten it.

2. Check and clean the connecting pipe between the bellows and the drainage filter. The dirt in the connecting pipe between the filter and the washing machine drain pump and the drainage pipeline should be removed to ensure that the drainage pipeline is unblocked.

Washing machines that use shaded pole drain pumps should check that the drain pump cooling fan is blocked. Due to transportation or other reasons, the plastic cooling fan of the drain pump may be entangled or blocked by debris, making the fan unable to rotate and preventing the drain pump from turning.

3. Due to improper use, coins, buttons and other objects fall into the chamber of the drainage pump, blocking the rotation of the impeller of the drainage pump and making it unable to drain water. The impeller chamber cover of the drain pump can be opened and the foreign matter can be removed, and the fault can be eliminated.

4. Small pieces of clothing enter between the inner and outer cylinders and are pressed against the lower drain of the outer cylinder, blocking the drain opening. At this time, the back cover of the washing machine should be opened, the heater or bellows should be removed, and the laundry should be removed with tweezers.

5. The drainage pump is damp and rusty, causing the rotor to fail to rotate, resulting in the drainage pump being unable to drain. Remove the drain pump, remove rust spots, add lubricant, and the fault can be eliminated.

6. Check whether the two wires of the washing machine drain pump are falling off, if the wires connected to the drain pump are intact, use a multimeter to measure the DC resistance of the drain pump.

7. It can be seen from the drainage circuit that the drainage pump is controlled by the two pairs of contacts -30 of the program controller, and the drainage pump works only when the two pairs of contacts are turned on at the same time.

8. The power supply voltage is too low, the drainage pump cannot be started, or the operation is weak, resulting in no drainage or slow drainage. Unplug the washing machine and measure the power supply voltage with a multimeter, if the voltage is lower than 187V, the drain pump will not work properly.

Operating tools: washing machine, drain valve, traction.

1. First check whether the adjusting rod nut on the drain valve is loose, which causes the tractor to be unable to pull the drain valve core apart and causes non-drainage.

2. In this case, we can fix the nut with the corresponding screwdriver or movable wrench, so that it can open the drain valve core.

3. If the nut is not loose or the cable is not loose, it may be that the tractor is damaged.

4. If the drain valve core cannot be opened, then we can replace the tractor.

The reason why the washing machine does not drain water

1. Blockage problem.

Blockages are a common cause of washing machines not draining water, so we need to check this aspect first. If the inspection finds that the drain filter of the washing machine is indeed blocked by foreign objects, the foreign objects should be removed when the state is empty. Once you've cleaned up the spine, put it back in place.

2. Foreign body obstruction.

I usually don't pay attention to the clothes when I throw them into the washing machine, and the small things in the pockets, such as coins and buttons, cause problems. At this time, take out the foreign object and the problem is solved.

Summary. Hello, very happy to solve the problem for you. If the drum washing machine can not drain the water, we only need to unscrew the sewage outlet at the bottom, after unscrewing, take out the sewage box, here is easy to be stuck by hairpins, steel hammers and other things, if you feel that the valve of the sewage outlet is loose, but you can't pull it, at this time it is possible to be stuck by those dirty things, in this case we need to put the washing machine down, open the drain pipe, and take out the clogged foreign objects in the pipe, then the drum washing machine does not drain the problem can be solved.

Hello, very happy to solve the problem for you. Hello dear if the trapped drum washing machine can not drain the water, we only need to unscrew the sewage outlet at the bottom, after unscrewing, take out the sewage box, here is easy to be stuck by hairpins, steel hammers and other things, if you feel that the valve of the sewage outlet is loose, but you can't pull it, at this time it is possible to be stuck by those dirty things, in this case we need to put the washing machine down, open the drain pipe, and take out the blocked foreign matter in the pipe, Then the problem of the drum washing machine not draining can be solved.

The washing machine does not drain may be blocked by the drain port, there is a lost electric valve for draining under the washing machine, and there is a wire pull rope in the middle, when we click on the switch button, this pull rope will pull the water switch in the banquet hall, so as to open the drain valve, so that the water can be discharged. If the electric valve of the washing machine is broken, it will not be able to pull the drain switch, and the washing machine will not be able to drain the water, which is the reason why the washing machine cannot drain the water.

CheckIf there is any foreign object blocking the drain port, check the adjustment nut on the drain valve. Check that the drain pipe is not bent and that clothing is not improperly placed, detailed steps:

1. Check whether the drain is blocked by foreign objects.

2. Check the adjusting nut on the drain valve.

3. Check whether the drainage pipe is bent.

4. Check whether the clothes are improperly placed.

How to repair the washing machine without water storage and drainage.

1. The drain pipe in the washing machine may also be damaged or blocked. A washing machine is made up of many parts. Once there is a problem inside the body, it is easy to cause the washing machine to not drain water.

You can check that the drain pipe of the washing machine is blocked or damaged, and dredge the drain pipe in time, if it is damaged, you need to replace the drain pipe with a new one.

2. The operation of the washing machine washing program may also be incorrect. Once the washing machine is used improperly, it is easy to cause the washing machine to not drain. Just follow the right procedure and you're good to go.

3. The water level in the washing machine may also be too high, and it may not be able to drain the water within the specified time. If the water level is too high, the washing machine will be overloaded while washing clothes, which will also cause the water to be unable to drain in the short term. You can wait a little longer, the water in the washing machine can be discharged normally, and don't put too much laundry when washing clothes.

4. If the drain of the washing machine is installed too high, the water in the washing machine cannot be discharged, and the position of the drain pipe needs to be lowered, and the fault can be eliminated.

5. If the washing machine drain gate assembly is loose or damaged, the washing machine cannot drain normally. Just tighten it or replace it with a new component.

6. If the fixing nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time.