How to maintain the fish tank so that it does not leak?

First of all, there are several situations of water leakage in the fish tank: the first is that the joints of the fish tank are glued, and water seeps or leaks outward. It's not big, but it's a nuisance, and the tank will keep flowing outward, making the surroundings wet.

If this happens, you can't sit idly by, and you need to fix it in time to avoid the leakage from expanding. If the leakage of the fish tank is very slight, and the contents of the tank are inconvenient to move, you can also use glass glue to repair it on the outside, and apply the glass glue from the outside to the leakage until it does not leak. Although this method is convenient, it can only be used for very minor water leaks, and serious water leaks must be kept dry before they can be repaired.

If the leakage is more serious, repair such a fish tank first to find out the leakage, and then remove the fish and other things in the tank, put the water clean, after the fish tank is dry, use a glue gun to pour glass glue into the leakage point, and then coat a layer of glass glue on the outside.

The second type of leakage is the appearance of cracks in the glass, which is most likely caused by the collision of the glass, which is very dangerous and can cause the fish tank to burst if not treated in time. In this case, the only way to deal with this situation is to dry the fish tank, apply glass glue to the inside and outside of the crack, seal it well, and preferably stick a glass on the outside. Such a sticky fish tank is actually not very reliable, if it can be replaced, it should be replaced in time.

It will also affect the aesthetics of the aquarium, if it is acceptable on the back or side of the inconspicuous back, if it is on the front, I am afraid that the fish tank will have to be scrapped. But this situation is all caused by human causes! Therefore, the fish tank is basically not returned!

So when we initially chose a fish tank, we tried to choose a thicker glass, 8mm is better!

The third case of water leakage, is due to the installation of the master sloppy caused by the leakage, usually the side filter cylinder is prone to this problem, that is, the installation master did not tighten the drain at the rubber pad, this is just the phenomenon of water seepage, that is, open the bottom of the bottom filtration door, you will find that there are wet water droplets at the bottom of the tank above the water pump, generally in this case can only release the water from the fish tank, and then find the installation master to re-screw it. If you screw it yourself, you need two people to cooperate at the same time, and it can be screwed!

Therefore, in order to prevent such a situation from happening, first of all, we should pay attention to the quality of the fish tank and choose a fish tank with excellent quality; Secondly, before buying a fish tank, set the position, fix it, do not move, so as not to bump during the movement, and finally the pipe fittings, accessories or something must be screwed and fixed. Only by satisfying these three points can we provide the best guarantee for the future fish farming process!

I recommend putting more soft sand under the fish tank.

If it is a square fish tank, you can also buy a protective cover to protect the four corners, and for other fish tanks, you can add an anti-shock pad under the outside to avoid breaking the weight.

You'd better buy a *** fish tank.

1. Fish tank leakage can be quickly repaired, and water cannot be released, first find the place where the bathtub seeps.

2. Take out the wallpaper knife and cut off the old glue at the seepage little by little.

3. Wear a disposable waterproof finger sleeve on your finger and squeeze the glue on your finger.

4. Use the glue on your fingers to evenly apply to the water seepage of the fish tank. Wait for the glue to dry.

Notes:Fish tanks with cracking and infiltrating water caused by external collisions, especially large fish tanks, have gone for a long time to increase cracking, and can not rely only on adhesives, it is best to rivet cracks on both sides, add stainless steel splints and other protection of two rivets.

The distance between the rivet and the crack should not be too short, and the rivet should also be coated with glue to prevent leakage. This method is generally not recommended. This method of repair is expensive and requires a professional to do it. Only large fish tanks are recommended.

Applied directly with acidic silicone glass glue, it cures quickly within five to ten minutes, and there is a faster quick-drying that can be used to fill the leak in just two or three minutes.