How do you tie a sweatshirt strap? Knotting method of clothing straps

1. First of all, make the length of one of the two ropes a little longer, as shown in the figure below

2. Tie two knots, as shown in the figure below

3. Pull the left rope back a little bit, and then pass through the hole in the middle to form a circle, as shown in the figure below

<>6. Finally, wear back to the middle, leave the fifth circle, for the sake of beauty, hide the rope end, as shown in the following figure:

7. Finally, the chrysanthemum knot is completed, as shown in the figure below

<> the second step, wrap the folded strap down, as shown in the picture below.

The third step is to wrap the tape in a circle to look like the one shown in the figure below, as shown in the figure below.

<> the fifth step and finally tighten the knot, as shown in the figure below.

1. The length of one of the ropes is a little longer, which is very important and will affect the length and overall effect of the later ties.

2. Tie two knots, leaving a gap between them, so as to facilitate the operation later, so that the rope will not be too tight to penetrate.

3. Pull the left rope back a little, and then go through the hole in the middle to form a circle, in order to test the length of the rope, leave the loop not too big.

4. The left rope is threaded back into the middle, leaving a circle again.

5. Pick up the rope on the right and pass it through the middle, leaving a circle as well.

6. Finally, wear it back into the middle, leaving the fifth circle, and hide the rope head for the sake of beauty.

7. The chrysanthemum knot is completed.

The straps on the sweatshirt are knotted in this way, which is fashionable and simple.

Knotting method of clothing straps: single tail type, double tail type, tight type, bow tie type.

1. Single tail type

Slip the belt into the buckle. Make a loop and thread the initial end of the belt through the buckle from bottom to top. Go through the freshly made circle from top to bottom. After completion, you can freely adjust the length of the sag by passing it through the loop you just made several times.

2. Double tail type

The belt starts with one end at the top and the buckle at the bottom and crosses each other. The initial end is threaded from the bottom up through the belt that clings to the part of the garment and tied in a knot. Make a circular motion and let the starting end go down from top to bottom again through the belt that clings to the part of the garment.

Let the initial end pass through the circle you just made, adjust the shape and you're done.

3. Firming type

Buckle the belt to the last hole. Let the initial end pass through the hole on the left side where the belt is secured. Go through the part that was originally close to the innermost layer of the garment. Once again, go through the hole on the right to secure the belt and you're done.

4. Bow tie type

The belt starts with one end at the top and the buckle at the bottom and crosses each other. The initial end of the belt is wrapped around the end with the buckle and made a circle. Wrap the initial end of the belt around the back of the cross and run it through the loop from the bottom up.

Adjust the shape of the knot to the bow tie and you're done. In this way, the clothes are tied with simple and stylish straps.

How to tie a knot in clothes with two straps1. It looks better to tie a bow, first wrap the strap of the clothes into a loop from the back.

2. Wrap the strap back from back to front.

3. Make a loop underneath the strap that comes back and pinch it with your thumb.

4. According to the above method, wrap 2-3 times according to the length of the clothes strap.

5. Thread the strap of the garment into the ring pinched by your thumb and tighten the knot.

1. Cross the two straps first, one on the top and one on the bottom.

2. The upper strap bypasses the lower belt, and then hangs down from the middle of the two straps and tightens it, and then ties a slipknot.

3. Fold the strap below into an S shape on one side of the bow and place it on the right side in the direction of the ribbon.

4. Then use the top strap to wrap it from the top to the bottom of the bow.

5. The top strap wraps around the bow on the right side and folds into a bow on the other side.

6. Slowly arrange the formed bow.

7. After a little more tidying, the beautiful and flat bow will come out.

As follows:

<> the second step, wrap the folded strap down, as shown in the picture below.

Step 3: Wrap the belt banquet Luzi in a circle into the shape shown in the picture below, as shown in the picture below.

<> Step 5: Finally, tighten the knot to complete the burning, as shown in the figure below.

<> the second step, wrap the folded strap down, as shown in the picture below.

The third step is to wrap the tape in a circle to look like the one shown in the figure below, as shown in the figure below.

<> the fifth step and finally tighten the knot, as shown in the figure below.

How to knot the sweater strap looks good, so that the knot is both fashionable and individual, and the method is simple.

The sweatshirt flat strap play style is auspicious and slow motion steps are as follows:Tool: Sweatshirt.

1. First of all, we prepare a sweatshirt and pick up one of the straps.

2. Then coil the rope up and wrap it around in a circle.

3. Then go around one, two, and three times to the back.

4. Then from the bottom hole through the back through the front to star.

5. Slow oak sells slowly.

6. Finally, pull it tightly and it's done.

How to knot the rope on the sweatshirt:

1. For braids, first grab one end of the drawstring of the sweatshirt and roll up a circle of sensitive limbs.

2. Then weave the rolled loop and the remaining part of the rope alternately, just like the ordinary braiding method.

3. Tie the knot to the end, pass the remaining part of the rope through the loop left at the end, and tie it tightly.

4. The second is a four-leaf clover knotted rope, first grab the end of the old chain sweatshirt drawstring and roll it upward, but this time it is a small circle in the middle.

5. Then pass the rope under the small circle through the small circle and then pull it out.

6. Repeat the same action, but this time don't go through, but leave a circle.

7. Then pass the upper part of the rope on the drawstring of the sweatshirt through this circle, and leave a circle when passing through, so that there is a small circle on the left and right sides of the grandson.

8. Finally, adjust the knot around the small circle to weave it into the shape of a four-leaf clover.

9. The third is the shape of a hydrangea, and two small circles are rolled out with the index finger on the drawstring.

10. Then grab the bottom end of the supergod and pass through the holes of the two small circles from the bottom to the top in turn.

11. Finally, pull it out and go around to the hole at the bottom, and pass through the hole in this circle.

The function of the drawstring: the wind resistance is actually used The two ropes on the sweatshirt and hat were originally used as a windproof effect, and the sweater and hat were very easy to be blown down by the wind when they were worn, and the two ropes could be tied tightly to prevent this problem.