Do I need to unplug the kettle after boiling water

The electric kettle needs to be unplugged after boiling water to prevent unsafe accidents.

Always keep the power plug, socket, power cord and automatic switch device of the electric kettle dry and clean, and should not be rinsed with water, so as not to damage the electrical insulation due to moisture, causing failure and leakage.

Flushing water or brewing drinks with an electric kettle that is still connected to the power after just boiling is easy to cause harm. Unplug the plug first, cut off the power supply and then take boiling water to ensure safety.

Every time the kettle has boiled milk, coffee, etc., a layer of residue and dirt may be attached to the electric heating pipe, and it should be carefully cleaned after each use. After a long period of use, some scale or other dirt will be attached to the inside of the pot or on the surface of the electric heating pipe, which should be checked and cleaned regularly. The automatic kettle should not be immersed in water when cleaning, so as not to affect the electrical insulation of the automatic switch.

Extended Materials. Maintenance work:

1) In order to prolong the service life of the kettle, the mineral sediment in the kettle should be cleaned regularly.

2) When cleaning, be sure to disconnect the power supply first.

3) Please do not soak the base of the kettle in water.

4) Mix the vinegar and water in a 1:2 ratio and pour it into the kettle, then plug it in, let the kettle work and wait for it to jump off automatically.

5) Let the mixture be stored in the kettle for 24 hours, then pour out the mixture, then fill it with water to a certain position, and then work.

6) Pour out the water to remove the limescale and vinegar, and finally clean the inside of the pot with clean water, if necessary, please repeat the above operation.

7) During the use of the electric kettle, if there is a failure, the kettle should be taken out of the heating chassis, the water in the kettle should be poured out, and then let it cool to room temperature before fault detection or cleaning.

From a user security perspective.

Unplug the socket side first.

Then pull out the side of the kettle.

Because the kettle side is often exposed to high temperatures.

Prone to damage. Just in case.

Or unplug the socket side first.

Poor contact causes too much resistance between the plug and the socket, and the heat burns out.

There are many reasons why sockets are burned out, generally the following:

1) Short circuit: check whether there is a short circuit phenomenon at the accident point or each power terminal, such as the socket and electrical equipment, and the instantaneous high current generated by the short circuit is the main reason for the socket to be burned.

2) Overload: Check and count the total power of all electrical equipment, whether it exceeds the load of the circuit breaker and overloads the operation.

3) Line aging: check whether the power supply line wires are aging.

4) Check whether the short circuit occurs due to the quality problem of the socket itself, causing damage.

The basic forms of short circuit are: three-phase short circuit, two-phase short circuit, single-phase grounding short circuit, two-phase grounding short circuit. An abnormal connection (i.e., short circuit) occurs between phases or between phases (or neutrals), sometimes when a very large current flows.

The current value is much greater than the rated current and depends on the electrical distance from the power supply at the short-circuit point. A short circuit is a low-resistance short circuit between conductive parts of different potentials, which is equivalent to a closed circuit directly connected by the wire without passing through the load.

Cause of burnt out line:

1. The power of the electric kettle is too large, and the heating current is too large, resulting in the burning of the power cord.

2. The power cord of the electric kettle is too thin or the quality is unqualified, and a square power cord is generally required.

3. The power cord is in poor contact with the kettle, and long-term use will cause the power cord to burn out.

Precautions: The electric kettle is not suitable for continuous use, after all, the power is particularly large, and the high current is not good for the indoor wires and power cords, and at the same time, pay attention to the kettle not to be too full, so as not to leak to the base in danger.

This is very important, it is best to unplug the power cord when the electric kettle is not in use, of course, if there is a switch on the socket plugged into the power cord, you can also turn off the switch, because it is safer, and it is the same for mobile phones to take some chargers. If it helps, please adopt

Very important, it is best to unplug the power cord when the electric kettle is not in use, of course, if there is a switch on the socket plugged into the power cord, you can also turn off the switch, because it is safer.

The kettle plug is not pulled out is will consume electricity, but the power consumption is not very high, the wattage of each appliance depends on its power consumption, if you have a socket for switching appliances in the kitchen, then turn off the switch directly without pulling the plug, if not, it is recommended to unplug it safer!

1. Does the kettle plug not be pulled out and consumes electricity?

Yes, especially for electrical appliances that consume a lot of power, it is also very troublesome to unplug it, and it is better to turn off the switch with a switch, such as the socket of the air conditioner needs to be equipped with a switch, and the switch needs to be turned off for a long time. Nowadays, many smart home appliances such as computers and TVs also need to turn off the switch not only because of power consumption, but also in some lines without lightning protection measures, thunderstorms are unsafe for electrical appliances.

Second, will the electric kettle burn if the plug is not pulled?

It mainly depends on the kettle you buy, and if it is a product from a roadside stall, it is estimated to burn out. The bottom of the electric kettle has two contact points, which may touch and cause electric shock if not properly designed, and then consider some unexpected situations, such as a paper clip that is common in the office falling into the base, or accidental water leakage and other situations that can cause short circuits and fires.

3. Do you need to unplug the electric kettle when it runs out?

1. The electric kettle is heated by the electric heating wire at the bottom after the water is energized, and the plug can be pulled out after use to prevent adults or children from accidentally touching the switch, and the electric kettle will start to produce dry boiling, causing damage and danger.

2. Split electric kettle, the chassis and the kettle body are separated, press the switch to make the chassis and the kettle body energized, but when the kettle body takes the plug and does not pull it out, the metal copper sheet of the chassis is in a energized state, and there is a certain danger of water spilling into it, and this situation can be avoided by pulling out the plug.

Yes, but it's best to turn it off.

The base of the electric kettle is designed to power the electric kettle. When the water is not boiling, if the electric kettle is still on it, it is best to unplug the power plug of the base to prevent the electric kettle from drying out. If not in use, do not place the electric kettle on the base, and there is no need to unplug the base.

It is used to boil water after the electric kettle is filled with water.

Attention needs to be paid to the use of electric kettles.

1. The electric kettle can only be used to boil water, not to boil milk, soup, coffee or tea, etc., and must be supervised during the boiling process, and the potatoes must be placed out of the reach of children, when the water is boiling. When boiling, the water vapor can cause burns, so pay attention to the maximum amount of water.

2. The water in the electric kettle should not be too full, otherwise it is easy to cause water overflow during boiling, which will affect the service life of the electric kettle.

3. When using the electric kettle for the first time, you can pour out the first pot of boiling water, the purpose of which is to disinfect the toxic substances remaining in the electric kettle.

4. Do not put the electric kettle on the surface of the heat source or next to the heat source, such as rice cooker, oven, etc., before plugging in the plug to turn on the power, be sure to turn off the kettle switch, do not dry, otherwise it will lead to the reduction of the life of the stainless steel base.

When the electric kettle is not in use, it is best to unplug the power supply, which is safer, especially if there are children at home.

The slow boiling of the electric kettle has something to do with the plug.

Common causes of slow heating are low power supply voltage, poor indoor power plug socket or line contact, which should be ruled out first. Then check whether the contact between the pot body and the stool letter power plug seat of the base is not in good contact, and whether there is serious fouling in the electric heating pipe.

Introduction to the electric kettle.

The working principle of the electric kettle is that the water vapor generated when the water boils deforms the bimetal sheet of the steam temperature sensing element, and this deformation pushes the power switch to power off through the lever principle. It is not self-resetting when it is powered off, so the kettle will not automatically reheat after the power is off.

Electric kettles were born in Chicago in 1891. With the development of science and technology, the fast, safe, convenient, and full use of energy have increasingly become the main characteristics of the kettle, and the British who love tea have fallen in love with it since then. In the 21st century, it has become a bestseller in the world.

The electric kettle adopts steam intelligent induction temperature control, which has the functions of automatic power-off after water boiling and anti-dry-boiling power-off.

With the needs of life, the current electric kettle is also developing in the direction of multi-function, such as leak-proof, anti-scalding, water locking, etc. The electric kettle has the advantages of fast heating speed, good heat preservation effect, strong filtration function and many styles.