-
This needs to be matched with a special computer for maintenance, and follow the tips above to operate [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
The hot car of this car is matched, and the computer is matched [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
Hello, you need a computer to match, 431 is OK [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
Hello, it's a pleasure to receive your inquiry. We'll be asking you for an analysis shortly. This can be matched manually, there are two methods, the first is to open the second gear, which is the gear where the instrument indicates full light, and then wait for 20 seconds, step on the accelerator to the end, hold for about 10 seconds, release the accelerator, turn off the ignition switch, pull out the key, and the initialization is completed.
The second is to open the second gear, hold it for 30 seconds, and then turn off the ignition and pull out the key. It should be noted that after the two methods are done, you have to wait for a period of time before you can try to ignition, generally wait for 15-20 seconds, and then ignition to see if the refueling is normal, whether the engine fault light is extinguished, if it is unsuccessful once, do it a second time, until it is successful, it can generally be successful at one time, at most twice. [If you have a problem with the car, ask the car master.]
4S shop professional technician, 10 minutes to solve. 】
-
Computer matching, enter 060 [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
1. Align the small notch of the timing mark on the camshaft with the blue link on the timing chain.
2. Align the timing mark triangle on the crankshaft gear with the blue link on the timing chain.
3. Install the tensioner of the timing chain.
4. Install the tensioning arm of the timing chain.
5. Mark the small dot on the timing of the balance shaft gear and align it with the blue link of the timing chain, and the operation is completed.
-
Skoda Octavia disassembles and matches the throttle.
Here's how:
Open the engine cover and the position of the throttle is clearly visible. In order to remove the throttle, the air filter must be removed first.
The hose connected to the throttle valve is removed. The two ends of the hose are secured with round iron hoops, and the iron hoops are fixed with screws, and the hose can be removed by loosening the screws.
<> here we recommend that if possible, it is better to use a sleeve to tighten the screws, because of the screwdriver.
It is easy to make the screw buckle, and the sleeve is relatively safer.
Once the screws are loosened, hold one end of the hose with both hands and step back firmly to remove the hose. Some car hoses may not be often disassembled or installed tightly, so it is not easy to unload, do not pull hard, it is easy to damage the hose, you can try to twist left and right at the same time, and then pull back after the whole is loose. The throttle valve can be seen when the hose is removed.
There will be a plug next to the throttle that needs to be removed before the throttle can be removed. For the car model that does not often disassemble the plug, the plug may be relatively tight, difficult to remove, at this time we can use a small screwdriver to pry around the plug, and it is easy to remove it after the overall loosening.
After removing the plug, the next step is to remove the throttle. The throttle is usually fixed with 4 screws, the upper two screws are easier to remove, and the lower screws are a little awkward. We recommend disassembling the two screws that are difficult to remove first, so as not to increase the difficulty of removing the lower screws due to the shaking of the throttle valve when they are finally disassembled because the upper screws have been removed and not fixed.
In our experience, here we only need to loosen the screws with the help of tools, and then it will be more convenient to remove the screws by hand, but be careful that the screws fall in the cabin.
After the <> 4 screws are removed, the throttle can be removed, and the exposed pipe is the intake tract. As you can see from the picture below, there is a lot of black carbon deposits in the air intake of our demonstration car.
However, we will talk about its cleaning in the future. Here we remind you that after removing the throttle valve, it is best to cover the entrance of the air intake with newspapers and other objects to prevent debris from leaking.
The method of matching the throttle of the Skoda Octavia:
The first is to open the second gear, which is the gear where the instrument indicates that it is fully lit, and then wait for 20 seconds, step on the accelerator to the end, hold it for about 10 seconds, release the throttle, turn off the ignition switch, pull out the key, and the initialization is completed.
The second way is to open the second gear of the key, hold it for 30 seconds, then turn off the ignition switch and pull out the key. It should be noted that after the two methods are done, you have to wait for a period of time before you can try to ignition, generally wait for 15-20 seconds, and then ignition to see if the refueling is normal, whether the engine fault light is extinguished, if it is unsuccessful once, do it a second time, until it is successful, it can generally be successful at one time, at most twice.
-
Summary. Dear, glad to answer for you! <>
Don't adjust it at will, because the throttle is still more important for the car power, comfort, etc. Moreover, the throttle position sensor senses the opening of the throttle and cannot be adjusted, and the opening of the throttle is controlled by the accelerator pedal.
Is the Skoda Skoda Octavia throttle angle adjustable.
Dear, glad to answer for you! <>
It's good not to adjust it at will, because the throttle is still more important for the car to burn the power, comfort and so on. Moreover, the throttle position sensor senses the opening of the throttle and cannot be adjusted, and the cracking degree of the throttle is controlled by the accelerator pedal.
However, special attention should be paid to the following points: 1. Before disassembly, the car key is removed, and the engine is in a power-off state. 2. After the throttle valve is removed, block the air intake with a clean cloth to prevent foreign matter from entering the air intake pipe. 3. When cleaning the throttle, use a special cleaning agent, and the upper end of the motor integrated circuit cover is upward, so as to prevent the cleaning agent from entering the integrated circuit and causing short circuit damage.
4. After cleaning, blow dry with air qiang, and touch the oil with the sealing ring to prevent air leakage. After the assembly of the source dissan 5, you must use a special instrument to match the throttle, if the old Honda machine is not successfully matched, the speed of idle and finch speed can not come down at 1600 rpm. After washing the throttle, you need to pull the high speed to remove the carbon deposit.
-
The Skoda throttle disassembly matching method on the Octavia is as follows:
Open the bonnet and you can clearly see where the throttle is. To remove the throttle, you must first remove the hose that connects the air filter to the throttle. The two ends of the hose are fixed with round iron hoops, which are fixed with screws, and the hose can be withdrawn by loosening the screws.
Here we recommend that if conditions permit, it is best to use a sleeve to screw, because the screwdriver is prone to scratching the screws, and the sleeve is relatively safer.
Once the screw is loosened, hold one end of the hose with both hands and push it back to remove the hose. Some vehicle hoses may not be easy to remove or not securely installed, so they are not easy to remove. Do not pull on them too hard, as this can easily damage the hose.
You can try twisting left and right at the same time to stare at them, loosen the whole thing and then take a step back. The throttle can be seen after the hose is withdrawn.
There will be a plug next to the throttle, and the plug will need to be unplugged before removing the throttle. For vehicles that don't pull the plug often, the plug may be tight and difficult to pull out. At this time, we can pry around the plug with the help of a small screwdriver, and it is easy to remove it after the whole is loose.
After removing the plug, the next step is to remove the throttle. Throttle valves are usually fixed with 4 screws. The top two screws are easy to remove, and the bottom one is more awkward.
We recommend removing the two hard-to-remove screws below first, so as to avoid that when they are removed at the end, the lower screws are difficult to remove, because the upper screws have been removed and not fixed, and the throttle is shaking. In our experience, here we only need to loosen the screws with the help of tools. It will be more convenient to remove the screws by hand afterwards, but be careful that the screws fall into the cabin.
After removing the four screws, the throttle can be removed, and the exposed pipe is the air intake. As you can see from the graph below, it is evident that there is a significant amount of black carbon deposits in the air intakes of our demonstrator car, although this will be discussed later. As a reminder, after removing the throttle, it is best to cover the entrance of the air intake with an item such as newspaper to prevent foreign objects from entering.
Octavia's throttle valve matching method;
The first is the second gear where the key is open, which is the gear where the instrument indicates the full light. Then wait for 20 seconds, press the throttle all the way down, hold it for about 10 seconds, then release the throttle, turn off the ignition, pull out the key, and the initialization is complete.
The second way is to turn on the second gear of the key, press and hold for 30 seconds, then turn off the ignition and pull out the key. It should be noted that after the two methods are done, it will take a while to try ignition, generally waiting for 15-mdash; 20 seconds, then ignition to see if the refueling is normal, the engine fault light is off. If you don't succeed the first time, you will do it a second time until you succeed.
It usually succeeds once, at most twice.
-
The Skoda Octavia valve is in the upper part of the Wang Xiangwei engine. The role of the car valve is to be responsible for inputting air into the engine and expelling the exhaust gases after combustion. In terms of the structure of the trapped engine, it is divided into intake valve and exhaust valve.
The function of the intake valve is to draw air into the engine and mix it with fuel for combustion; The function of the exhaust valve is to exhaust the exhaust gases after combustion and dissipate heat. The symptoms of car valve damage are as follows:
1. It will affect the working efficiency of the engine, and the power of the car will be reduced;
2. There will be abnormal sound of lead banquet, the engine will be unstable or unsmooth acceleration during operation, and the overtaking performance will also be reduced, and in serious cases, it will also lead to difficulty in starting the engine, and the phenomenon of not igniting will occur, and the car will also have air leakage or increased carbon deposits;
3. If the valve is broken, it will lead to unstable cylinder work, and unstable cylinder will cause the engine to shake, the engine will work weakly, and it will also lead to the blockage of the exhaust pipe, and in serious cases, it will also lead to black smoke from the exhaust.
-
Summary. Hello Skoda Octavia throttle control unit does not start matching. This requires throttle matching, and cleaning the throttle is matched with an instrument.
Hello Skoda Octavia throttle control unit does not start matching. This requires throttle matching, and cleaning the throttle is matched with an instrument.
1 Enter the engine system, enter the basic setting channel, enter 060, and wait for the display to be adaptive and normal.
2. It is recommended that the vehicle should clean the throttle every 2-30,000 kilometers, support the disassembly and cleaning method, and do the throttle initialization after cleaning.
3 cleaning the throttle valve is best to disassemble all to clean, each pore is cleaned with cleaning agent, but the line is blind is that some models have to be decoded after pulling the plug, although the wash is clean but can not be cleaned by themselves, in the car to start the state to clean some small channel gear digging empty there is no way to clear and wash thoroughly.
4 throttle is dirty (requires group lead cleaning and matching), which is very common. or throttle damage and throttle-related circuit failure, etc. It is recommended to go to the workshop for repairs.
Preheat the engine to normal operating temperature; Turn off the ignition and wait for at least 10 seconds; Make sure the accelerator pedal is fully released, turn the ignition to the ON position, and wait 3 seconds. The rain sensor installed in the base of Bora's new rearview mirror can adjust the speed of the wiper movement according to the amount of rain falling on the glass. And the wiping speed can be automatically adjusted at any time according to the rainfall.
In addition, the sensitivity of the sensor that controls the wiping frequency can also be set to meet the individual needs of users with different habits. Equipped with a new intelligent wiper, the wiper frequency can be automatically adjusted according to the rainfall when driving in rainy days, ensuring that the driver's vision is good and greatly improving driving safety; The boneless wiper collapses well against the curved glass, and the force is even, which ensures that the wiper is cleaner and reduces the trouble for drivers and passengers to use the car. <>
-
1.Remove the engine assembly.
2.Align crankshaft keyways and timing markers.
3.Align camshaft sprocket timing marks 2 and 3.
4.Install the timing chain, making sure that the links with the markings and the 6 are aligned.
5.Retract the tensioner and lock it with 1 pin 7.
6.Install the tensioner, tightening torque: 11nm.
7.Install the tensioner linkage 8, and remove the pin 7.
8.Turn the crankshaft 2 times clockwise until the crankshaft keyway aligns with the timing mark.
9.Check that the timing marks on the camshaft sprockets are aligned.
Hello, it is recommended that you wash the throttle once every 10,000 kilometers, and if you have the conditions, wash it yourself every 5,000 kilometers.
1. First of all, adjust the angle of the rearview mirror of SAIC Volkswagen Skoda Octavia and insert the screwdriver into it. >>>More
SAIC-GM Skoda Octavia does not ignite, the instrument light does not light up ASR light indicates that the throttle electronic system is faulty, and the Skoda Octavia throttle electronic system needs to be initialized and reset, and the specific operation steps for the initial reset of the Skoda Octavia throttle electronic system are as follows: >>>More
Octavia. If you think about it this way, Skoda's brand influence is far inferior to that of Volkswagen for two models of the same level created on the same platform, so the price point and maintenance are very attractive to the Volkswagen. The value retention rate of used cars is indeed lower than Skoda, but the cheaper new car makes up for it.
On the general highway, if you don't go uphill or go against the wind, you can drive up to 240km h. If you go downhill and downwind, the maximum speed can be even higher.