What kind of wax is generally bought outside of mahogany boiling wax that specializes in treating wo

with solid wax. Solid wax is often used to protect topcoats and is sometimes used to finish bare wood furniture. This method is best suited for fully sanded smooth, dense-grained hardwoods, such as maple.

Some waxes add color and are specifically used for darker woods, such as walnut. These waxes paint the wood, and if the topcoat applied to the wood is uneven, the colored wax can be used to cover the imperfections. However, wax cannot color wood or restore the topcoat.

Before using the polishing wax, check that the surface of the paint layer is intact. For newer wood furniture, the surface dust should be wiped off with a muslin cloth first, and the stains that have been left for too long or are difficult to remove can be wiped with a cotton cloth dipped in a small amount of gasoline or alcohol. Secondly, use a piece of cotton cloth to polish an appropriate amount of wax and coat a large area, and then use a larger dry cloth to wipe the wax evenly according to the circumferential block, so as not to leave traces as the standard.

If the wax is used too much, it will not only leave streaks and markings, which will affect the luster, but also soften the paint layer over time, which is not easy to remove. It should be noted that the area where the paint layer has been damaged should be treated before waxing. If the scorched area is limited to the surface paint, you can use fine sandpaper dipped in water and gently grind away the stain, then apply wax.

If the surface is scratched but not deep into the wood, it can be directly polished with polishing wax. Shoe polishes of similar colors can do the same.

The wax used is liquid beeswax. Waxing is a very practical and common way to protect wood.

The specific steps are as follows:

Step 1: Melt the wax.

The beeswax is heated in a metal container and melts into a liquid.

Step 2: Use a two-pass (or three-pass) bristle brush to spot the beeswax on the furniture like a scattered star (one side at a time).

Step 3: Blanch the wax.

Wax scalding process. Heating with an electric pantograph, when holding the pantograph is heated, be sure to keep moving, and use a large plate brush to evenly brush the wax back and forth to all parts, and the pantograph should move with it. Be careful not to burn**, this step is the most critical.

If the moisture content of the (new) furniture is high, the heating must be gradual, not too violent, so that the wax gradually penetrates into the inner layer of the wood. When the wax foams evenly and no more.

Continue until the inner layer of wood seeps in.

Step 4: Waxing.

Use a wax driver to shovel the remaining floating wax on the surface of the furniture until it feels non-sticky to the touch.

Step 5: Wipe the wax.

Rub it repeatedly with a cotton cloth like a bath until it is shiny, and it is better to feel lubricated.

The wax used to cook wood is liquid beeswax. Waxing is a very practical and common way to protect wood. The specific steps are as follows:

Step 1: Melting Wax The beeswax is heated in a metal container to melt into a liquid. Step 2:

Use a two-(or three-pass) bristle brush to dot the beeswax on the furniture like scattered stars (one side at a time). Step 3: The wax scalding process is heated with an electric bow, and the pantograph must be kept moving when it is heated, and the wax is evenly brushed back and forth to all parts with a large board brush, and the pantograph should move accordingly.

Be careful not to burn**, this step is the most critical. If the moisture content of the (new) furniture is high, the heating must be gradual, not too violent, so that the wax gradually penetrates into the inner layer of wood. When the wax blisters evenly and does not continue to seep into the inner layer of the wood.

Step 4: Waxing Use a wax You Bihong driver to shovel the remaining floating wax on the surface of the furniture until it feels non-sticky to the touch. Step 5:

1. The operation is different

Waxing needs to be carried out in strict accordance with a series of steps such as boiling, baking, scraping, wiping, etc., while waxing is only to wipe the wax on the furniture with tools.

2. The time is different:

Waxing usually takes a while and is a very careful process, while waxing usually takes only one or half a day.

3. The duration is different:

1) With the passage of time, this protective film is constantly affected by factors such as air oxidation, human hand touching and wiping with rags, so that the surface, edges and edges of the furniture appear a natural, translucent, warm and moist surface form.

2) Waxing is to rub wax on the surface of wood, and after one or two months of use, it will gradually disappear.

The mahogany wax boiling and drying process uses liquid beeswax.

Mahogany wax boiled wood drying technology uses chemical drying, which refers to the use of organic or inorganic compound solutions or vaporization as drying medium to heat and dry wood. Wood is boiled in a hydrophobic solution of wax liquid, which can be heated in a solution higher than 100 degrees Celsius and dried quickly in a boiling condition because the boiling point of paraffin liquid is higher than that of water. This drying method reduces the temperature absorption of the wood and enhances the wood corrosion resistance.

However, in the process of cooking, although the wax will penetrate into the wood little by little, the temperature and process of the wax cannot be mastered, which may damage the woodiness of the wood. Secondly, cook the wood with soil wax, if the temperature is not well controlled, the wood is easy to deform or burst.

Your question, the mahogany wax boiling and drying process uses liquid beeswax; Best wishes for the Year of the Snake!!

Method steps.

1. Mahogany furniture waxing is divided into closed waxing and open waxing, if it is closed waxing, it is necessary to use an explosion-proof agent for mahogany semi-finished products, close the wood eye of the mahogany, so that the inside of the wood can not exchange moisture with the outside world. If you open the waxing, you don't need to put on the anti-explosion agent.

2. Closed waxing: For mahogany products with explosion-proof agent, it is necessary to give the product a batch of ash to fill the wooden eye. Open waxing does not need to batch ash.

3. The mahogany products that are given batch of ash should be dried. The process of back closed waxing is the same as that of open waxing. The mahogany products need to be sanded with sandpaper until the surface is smooth and smooth.

4. Molten wax, hot wax, etc., by manually using a soft cotton cloth dipped in beeswax solution on the surface of the polished furniture to wipe, dry, wipe ,..Until the waxed mahogany furniture has a smooth surface and meets the requirements.

5. For waxing and maintenance of mahogany furniture, it is necessary to wax after dust removal and cleaning. Generally, after one month of use of mahogany furniture, wipe the wax with a soft cotton cloth with wax, and wax it once a quarter. Try not to let the mahogany furniture come into contact with water and moisture when waxing.

First of all, wipe the furniture with a clean rag, first remove the dust on the surface of the furniture, especially the places that are easy to fall dust. Then use a brush to dip an appropriate amount of Mo Luo and apply gently. Be careful not to be too sticky.

Hold the edges first, and then apply the middle part to avoid leaving too much wax on the edges. After applying the wax, wait 3 to 4 minutes before applying, and wipe off the excess wax with a towel when it is not completely dry.

How do you wax mahogany furniture? Mahogany furniture has received praise from the majority of collectors for its graceful and luxurious appearance, but there are many friends who rack their brains for how to maintain mahogany furniture, and even because of the wrong maintenance method, the quality of mahogany furniture is damaged.

A month after the purchase of new mahogany furniture, it is necessary to wax once, to choose natural wood wax, wiping supplies can not be chosen at will, it is best to use soft cotton cloth, so that it will not hurt the surface of the mahogany. From then on, waxing should be done regularly at regular intervals. The interval can be one wax refill every month and one full wax every quarter.

Don't wax too often, but be sure to remember when you'll wax next.