What should I do if my home is heated but the temperature in my bedroom is not high?

Updated on home 2024-08-03
18 answers
  1. Anonymous users2024-02-15

    It's the same at home, the bedroom is 2 3 lower than the living room.

    Underfloor heating, water separator is used.

    It's right in the living room. The heating duct in the living room is close to the water divider, so there is almost no heat loss. The bedroom is different, the pipe from the water separator to the bedroom has to lose part of the heat, and the temperature of the hot water in the bedroom is reduced, and the heat dissipation capacity is naturally reduced.

    For example, someone in the house of a refrigerator with a side wall that the lower part is hot and the upper part is not hot, because the high temperature and high pressure refrigerant comes out of the compressor.

    It flows through the condenser from bottom to top.

    The pipeline, as soon as it enters the condenser, it will liquefy and release heat, and when the upper part is released, there will be less heat.

    In addition, I live in a side house, the living room is in the middle, and the bedroom is on the side, and the insulation performance of the bedroom is not as good as the living room.

    If the whole house is radiators.

    The size of the radiator, the installation position, and the height of the layer will affect the temperature, and the radiator installation should be as low as possible, and the heat dissipation of the plate type is better than that of the column type, and the installation of the radiator is as close as possible to the door and window position, which can heat the cold air entering the room in advance, and the temperature balance of the room is higher.

    Due to the above two reasons, the temperature in the bedroom is a little lower than that in the living room, so it is normal. In addition, the distribution of pipes will also affect the heating effect, because I don't know how to arrange it, so I don't discuss it.

    The spacing of floor heating coils is generally between 10 cm and 20 cm, usually 15 cm and 20 cm are mixed, and the floor heating coils should be denser in places with poor thermal insulation, and the spacing of 20 cm is used in areas with better heat preservation. It is not that the denser the better, too dense will have an impact on the ground material, the indoor temperature is too high, but it will be very dry, too sparse will easily cause the temperature to rise.

    Conclusion Through the above analysis, these items are the main reasons why the temperature of the living room is higher than that of the bedroom, we can use it as a reference direction, if the temperature difference is too large, it is best to ask a professional HVAC engineer to check the reason. I hope mine can help you, if there are any deficiencies in the point of view in the article, please leave a message to correct.

  2. Anonymous users2024-02-14

    If the heated room is not hot, it is most likely due to a problem with the insulation in the bedroom. We've been in this situation before, and this approach can be done by adding insulation to enhance the warmth of the bedroom. Of course, you can also switch to floor heating, and the heating effect of floor heating is sometimes better than water heating.

  3. Anonymous users2024-02-13

    Check whether the vent is blocked, if the fire is blocked, it will not be particularly strong, and the temperature will rise slowly. If there is no water circulation, install one, the temperature will rise quickly, and the room will be sealed.

  4. Anonymous users2024-02-12

    Point 1: If the temperature in the bedroom is not high, it is best to put the heating water on it, the effect is good, point 2, if the temperature in the bedroom is not high, it is best to pay attention to the window must be tight, so that it will be very warm, and the third point should be done to clean some dirty things in the heating frequently.

  5. Anonymous users2024-02-11

    If you don't feel the temperature in the bedroom is particularly warm, it may be because the living room in the bedroom is too far apart. Then the supply of heating will be limited to a certain extent, so we will feel not so comfortable, and we will also feel that the heating temperature in the bedroom is not up to it, it is also recommended that you can let professional staff help you solve this problem. <>

    If our bedroom is not heated, and the heating is usually provided mainly according to the living room, then it may be because the distance between our living room and the bedroom is too far. There is no way to supply the heating to the bedroom, so we will feel that the temperature in the bedroom is very insufficient, and the second reason is that our heating pipes may be used for too long. If the heating pipe is used for too long, it is easy to cause the indoor temperature to drop, etc., in addition, it may also be because of the heating equipment we purchased.

    If the heating equipment is not so good, it is also likely to lead to the phenomenon of insufficient heating. <>

    First of all, we need to find a professional staff to help us check the stomach and heating, there will be a lack of temperature, and then according to the problem to prescribe the right treatment. If you buy the heating pipe too cheaply or the heating pipe is used for too long, then we have to replace the heating pipe, if it is because the distance between the living room and the bedroom is too far, we can install some heating pipes in the bedroom area.

    Now the weather is very cold, so heating is a very important thing, so it is recommended that you should solve it early. When decorating at ordinary times, the choice of heating pipes must be better chosen, otherwise, there will be some problems in the follow-up, and it will be too late to regret it.

  6. Anonymous users2024-02-10

    It may be because the floor heating is not complete enough, or there may be a problem with the floor heating in the bedroom, or it may be that the bedroom is in a state of shade, so the temperature in the bedroom will be relatively low.

  7. Anonymous users2024-02-09

    It may be because the heating pipe is blocked, you can find a property, and there is a related company to unclog the heating pipe, or it may be that the heating valve in the bedroom is not opened.

  8. Anonymous users2024-02-08

    It may be because the heating capacity is insufficient, or the bedroom is poorly sealed, so the temperature is relatively low.

  9. Anonymous users2024-02-07

    It may be that the distance between the bedroom and the living room is too far, causing the temperature heat to not reach the bedroom.

  10. Anonymous users2024-02-06

    For example, if the heating equipment is decorated at home, then the heating equipment may only be found when it is used, if it is found that the heating temperature in the living room is OK, but the heating temperature in the bedroom is not enough, this situation must have occurred in many family members, what is the specific reason, first talk to you.

    First, the first reason, it is likely that the bedroom is too far away from the living room, if it is too far apart, the heating ** to the living room, it and the bedroom distance is not enough, the temperature of the heating can not reach, so there will be a bedroom temperature is not very high, this situation has appeared in many places, mainly depends on the heating equipment, because the equipment is not very good, and then some of the equipment and the actual operation of the problem occurred, resulting in the temperature of the bedroom is not enough, This problem can only be done by refitting the heating pipes in the bedroom. <>

    Second, the second reason is that the heating pipe is used for too long and the temperature is not up, because the heating in many families has been used for many years, and then over time, the quality of the heating pipe requires these to decline, once the temperature drops the standard, and even sometimes there is no direct response, for this situation or many families have appeared, after all, anything has a life, if once it exceeds the life or is close to the life of the event, there will be some unnecessary trouble. <>

    3. This reason may be because the heating equipment you buy is too cheap, because the heating equipment is cheap, it will lead to the heating temperature, and if the temperature is not up, there will be some extreme reactions to the heating at this time, either there is a problem, or the temperature is not up, or you can't experience the body temperature, so when it is recommended to buy a heating pipe, it is best to buy a better brand of heating pipe, so that the use time is relatively long, and there will be no small problems. <>

  11. Anonymous users2024-02-05

    It may be that the heating in the bedroom is blocked, and if the heating is blocked, the temperature cannot be very high.

  12. Anonymous users2024-02-04

    It could be that the living room and bedroom are too far apart, there may be a problem with the heating pipe, or there may be an air leak.

  13. Anonymous users2024-02-03

    This situation may be caused by a blockage in the floor heating pipes in your home, as long as you find someone to clean the floor heating pipes.

  14. Anonymous users2024-02-02

    In winter, the temperature in the house is quite high, but the heating is not hot, what is going on, hello dear, I am very happy to answer for you, oh <>

    1. Gas accumulation. The indoor heating part is not hot because the radiator has gas in the area, which causes the phenomenon of "gas blockage", and it is recommended to vent the radiator. 2. Hydraulic imbalance.

    Some radiators are not hot, but the hot ones are turned off and the ones that are not hot can be heated up, a phenomenon called hydraulic imbalance of the indoor circulation system. To deal with this situation, the room system can be adjusted to turn off the hot heater first, let the non-hot heater heat up, and then slowly turn on the hot heater. 3. Blockage or unreasonable installation, unauthorized modification:

    If the above methods can not be solved, then the radiator or pipeline may be blocked or seriously installed unreasonable, at this time, it is necessary to ask professional maintenance personnel to disassemble and inspect to eliminate the blockage or reinstall the reasonable installation of the pipeline to eliminate. 1. The device of the radiator is down, that is, the radiator is installed on the top with a water retainer, and the bottom has become straight, and the hot water has gone away from the top. It is also formed because of the water retaining sheet.

    2. There is no water stopper, the water pressure is too great, the cold water and hot water barrier of Chunxiang Chong are washed off, and the cold water below cannot flow back. Such a situation is rare, just close the water inlet valve a small point, there should be no achievement without adding a water retaining sheet on it, but the heat dissipation is less than the original. 3. Even if there is too much air in the lower banquet, it is also necessary to deflate at this time.

    1. The radiator is too small. In this case, it may be that the selected radiator is too small, and the number of radiator pieces needs to be increased. Therefore, when buying a heat dissipation machine, you must actually measure it, and calculate the size of the radiator according to comprehensive factors such as orientation, surrounding environment, and pressure.

    2. The home decoration is serious, and the radiator covers a large area. The interior decoration is severe or covered by curtains and other items, which affects the heat dissipation, which in turn affects the indoor temperature. Therefore, for home decoration, try to pack less radiators and leave a certain amount of space for heat dissipation for radiators.

    Hope the above helps you<>

  15. Anonymous users2024-02-01

    After the heating period of the central heating every year, all the water in the pipeline system will be pumped back, and the water will be re-added before the heating is re-heated, so there will be air at the end of the equipment (the radiator group at home), and the exhaust valve needs to be unscrewed to exhaust when the heating is not hot.

  16. Anonymous users2024-01-31

    <> "During the use of the heater, sometimes it will not be hot. So, what to do if you have a bedroom where the heating isn't hot? What is the reason why the heating in my home is not hot? Let's find out.

    There is a bedroom heating that is not hot.

    In this case, we can first check the radiator or pipe in the sleeper room to see if there is a blockage problem and what causes the blockage. If it's a limescale problem, just clean it up. If there is a blockage caused by air in the pipe, then it is necessary to open the air release valve to deflate, and wait until the air inside is drained.

    However, if it is caused by a damaged valve in the distribution manifold, you need to contact the heating department and ask them to arrange for someone to come and replace it.

    Home heating is not balanced state heat causes.

    1. The heating system is blocked.

    The heating system is one of the common reasons for the heating is not hot, for this situation, we can first touch the pipe connected with the corridor with our hands, if it is not hot, it may be a blockage problem, and the main causes of blockage are the bridge cover.

    First, due to the lack of maintenance and maintenance of the heating system for many years, a large amount of scale and sediment are accumulated in the pipe, which causes the pipeline to be blocked and needs to be cleaned. There is also a kind of residence on the top floor, and the pipeline valve is closed, which can only be solved by contacting the property.

    2. The radiator is not hot.

    For central heating, it takes about a week for it to heat up as a whole, and if it does not heat up within this time, then you need to contact the heating company to deal with it. However, the heat cycle of some pipes in the early stage of heating will be relatively slow, especially for the community that is still in the pressure testing stage. Therefore, if your radiator does not heat up in time during the heating period, then don't worry, and the pipe temperature will return to normal when it reaches the specified temperature.

  17. Anonymous users2024-01-30

    <> can be used to release the first gas of the shed, discharge water and add water, clean up the blockage, adjust the control valve and other methods. First of all, the method of deflation can be employed. The radiator should be deflated regularly, so that the air in the air can circulate, and it is easy for the hot gas of the heating to circulate.

    Secondly, you can put water or add water, the radiator is not hot, it may be due to the lack of water in the number of chain dates, and it is necessary to discharge part of the water and rock yard and then add new water. Again it can be washed. Inside may be due to blockage, and then the gas flow is not smooth.

    In addition, the control valve can be adjusted to balance the heat of the radiator.

  18. Anonymous users2024-01-29

    For winter, heating is very important, after installing heating, the corners of the home will be very hot, so that you don't have to worry about feeling cold when you wear thin clothes at home. Radiators carry heat to each room because of the circulation of water, and if only one bedroom is not hot, then there is a problem with some part of the radiator system. So what's the solution?

    If one room is hot and the other is not, it's definitely not a problem with the whole system. You can see if the radiators or pipes in a room that is not hot are clogged with limescale, causing the hot water to not circulate properly. The heat transfer efficiency of limescale is very poor, and the thickness of the scale can affect the heat transfer.

    The way to clean is to close the other valves on the water separator and then clean the pipes in the room, preferably by a professional cleaning professional.

    Then there will be air blockages inside the pipes and radiators, which is also the main reason for heating some rooms. When there is a lot of air in the ducts, an air blockage can form inside, making the water in the radiator flow poorly. This will happen over time.

    If it is a careful underfloor heating, it may be that the valve of the manifold is broken, and there are internal valves for loop control on the supply and return pipes. If the circuit control valve is damaged, note that the valve is open. When it is in a closed or semi-closed state, it will cause the floor coil of this floor heating circuit to not heat up.

    In this case, you can usually turn down the valve of the hotter radiator and let the silver clear water transfer to the other radiator. You can also take a look at the water separator, which is usually installed under the wall and is a pair of switches, it may be that the water separator valve in the tube bedroom is not open, or it is not opened properly. If the separator is normal, it may be that the filter of the heating valve between the pipes in the corridor is not clean, and you can find the property to solve it; Or there is gas in the radiator with a wide beat, which can be exhausted with an exhaust valve.

    Then there is the aforementioned radiator valve that turns down the heat a bit. If it still doesn't work, it could be due to other issues, such as the radiator being blocked during the decoration process, the water inlet and outlet being installed backwards, etc. These issues need to be handled by someone else.

    1.Before entering the house, the heating is usually controlled by valves. The heating is not hot. The first thing to check is if the valve is open. Before use, the user must open the manual valve in advance.

    2.The radiator in the living room is hot, while the radiator in the bedroom is cold. This could be the case that the heating circuit in the home is blocked.

    3.If a dwelling's water separator is half-hot and half-cold to the touch, it must be considered whether it is "air blockage". This situation is the easiest to solve.

    Each radiator has a spiral-shaped exhaust valve at the end. You just need to unscrew the exhaust valve and expel the air until there is a steady flow of water out.

    4.If the underfloor heating in your home was hot before it happened frequently and it got hot in a short period of time, and you often hear the hum of the heating pipes, it is possible that your neighbor is using a circulating pump. In this case, residents can promptly report their complaints to the heating company after coordination fails.

Related questions
10 answers2024-08-03

In the process of home decoration, the selection of doors and windows is very important, it brings security to our home life, there are many window decoration materials on the market, so which material is better for windows? Next, let's take a look at what kind of materials are good for window decoration and the precautions for installing doors and windows! >>>More

9 answers2024-08-03

The operation process of wall decoration is more complicated, there are several kinds of raw materials, and the actual effect is different for different types. If you ask what is more difficult to manipulate in interior decoration, I believe that many friends will vote for the wall and want to install a simple white wall, but who would have thought that this is assembled as a cheap house for rent, and can't help but feel that it is really difficult to assemble the wall! In fact, no matter how you decorate the design, everyone wants to decorate the most beautiful wall with the least estimate, <> >>>More

18 answers2024-08-03

1. It is best not to move in after the decoration of the new house, because the first year after the home decoration, especially the first half of the year, is the strong release period of harmful gases such as formaldehyde and benzene. >>>More

19 answers2024-08-03

Fuse. It is mainly used for short-circuit protection, thermal relay. >>>More

18 answers2024-08-03

Generally, we don't need to brush the primer when we paste the wall covering, but before pasting the wall covering, we must ensure that the wall surface is relatively flat, and if there is an uneven place, it is definitely not possible to paste the wall covering, so it is best to scrape the wall again.