Where does the oil pumped by the pumping unit go The pumping unit cannot pump oil

Range hood believes that everyone is familiar with it, and our life is closely related, usually when we cook in the kitchen, a large amount of oil smoke will be generated, oil smoke choking people are uncomfortable, you need a range hood. Many people have doubts, what we see is a lot of smoke smoked, but every time we clean the range hood, we will find a lot of oil. Because in the range hood to smoke the smoke into the hood,Part of the fumes will be discharged, and some of them will gradually liquefy as the temperature drops, and then the liquefied oil will drip into the oil cup, and when the oil cup is full, it will overflow

The oil cup needs to be cleaned regularly, if the oil cup is full of oil stains and overflows, it will cause the kitchen utensils to be dirty with oil and difficult to clean and will cause the effect of oil absorption not to be achieved.

There are also certain skills in the installation of range hoods, because if they are not installed properly, they will not have the expected effect。The height of the range hood installation also needs to be noted: a certain height is required, otherwise it is easy to hit the head, and it will be stained with oil stains and oil smell, but also to ensure that it can be smoked.

The range hood is difficult to clean, many people are worried that the range hood is difficult to clean, and a few small methods can make the range hood simple to clean and not distressed. Method 1, turn on the range hood, spray a layer of special range hood cleaner evenly, and wipe the rag with hot water. Method 2: Add hot water, soda, and dish soap to the watering can, shake well, spray it on the place that needs to be cleaned, wipe it off well, and the sewage will flow down the oil cup.

The waste oil that is usually cleaned can be collected without throwing it away, and it can be used for a lot of things。Usually, if you raise flowers and plants at home, whether the flowers and grass grow well or not, it depends on whether there is enough nutrition, usually flower fertilizer needs to be bought, and waste oil can be used as flower fertilizer, its fertilization effect is also better than the general flower fertilizer. Waste oil contains a lot of nutrients, can supplement the nutrients needed by plants, promote growth, usually there is a need for a key in the home for a long time, the lock will be difficult to open, then you can apply a little oil, it will be very easy to open.

The waste oil in the range hood can be used as "waste", and there are many small uses, as long as we observe carefully, we will find small tricks and tricks in life。I'm only talking about a part of it, if you're interested in this, you can explore it yourself.,Usually a very small thing.,It's also very valuable.,Did you understand?。

The principle of the pumping unit is to inject water into the place where there is oil, and the density of water is greater than that of oil, so the oil will rise, so the oil pumped by the pumping unit will pump the oil to the place we need through this method.

The oil pumped by the pumping unit is put into a storage box inside it, temporarily placed inside, and poured out when it is full!

In family life, when you open the lid of the range hood, you can find that there is a thick layer of oil attached to the inside of the hood, and the fan surface inside the range hood is also attached to a very thick layer of oil.

Kiss! Hello Xixu, happy to answer your <>

The solution to the problem of the pro-pumping unit can not pump the tanker is as follows: 1. It may be that the partition in the middle of the exhaust pipe is not directly placed or not opened, and there is a door in the exhaust pipe of the old range hood that can be opened. 2. There is also damage to the reversal of the wind wheel.

3. The smoke exhaust pipe is blocked. 4. The capacitor is damaged, which leads to the reversal of the motor of the range hood, so it is very likely that there will be no drop of oil in the dripping box, so the range hood does not smoke, and it must be checked one by one to check its fault. I hope my reply will help you <>

Do you have any other questions?

Summary. Hello! The reason why the pumping unit can't pump oil and the solution is because the pressure pump of your pumping unit is insufficient, which will cause it to not be pumped.

If you shake it heavily, it's blocked, so try turning it upside down a few times. If you shake it very lightly, it means that the oil drum is running out of oil, or it is leaking, so try to shake it quickly for dozens of times. If you shake it easily and can't pump oil, it is generally because the inner sealing ring is broken and leaking, and it needs to be replaced.

Or shake it quickly a dozen times and try to get it on again. If it is very heavy to shake, it may be blocked, so try to turn it upside down a few times. The engine is turned off, open the front hood of the sedan and pull out the dipstick.

Adjust the upper degree locking clamp of the sucker pipe so that the length of the end of the oil pipe extending into the engine room is equal to the length of the dipstick Insert the sucker pipe into the dipstick hole and confirm that it touches the engine oil pan. Close the pumping unit drain valve.

What to do? Hello! The reason why the pumping unit cannot pump oil and the solution is because your pumping unit is pressed well and the pump pressure is insufficient, which will lead to the failure to pump.

If you shake it heavily, it's because the sock is blocked, so try turning it upside down a few times. If you shake it very lightly, it means that the oil drum is running out of oil, or it is leaking, so try to shake it quickly for dozens of times. If you shake it easily and can't pump oil, it is generally because the inner sealing ring is broken and leaking, and it needs to be replaced.

Or shake it quickly a dozen times and try to get it on again. If it is very heavy to shake, it may be blocked, so try to turn it upside down for a few turns. The engine is turned off, open the front hood of the sedan and pull out the dipstick.

Adjust the upper degree locking clamp of the sucker pipe so that the length of the end of the oil pipe extending into the engine room is equal to the length of the dipstick Insert the sucker pipe into the dipstick hole and confirm that it touches the engine oil pan. Close the pumping unit drain valve.

Hello! The above are the reasons why the pumping unit cannot pump oil and the solutions.

The above is the full reply of the teacher2Have more questions? The teacher can continue to answer your <>

Looking forward to serving you again <>

I wish you a happy life and all the best! 4.If you are satisfied with my service, please give a thumbs up and wish you all the best again! Peace and joy <>

What is the reason why the pumping unit always runs oil?

Dear, I'm honored to have your question The information that the teacher found out to you here is: what is the reason why the pumping unit always runs oil: the reason why the pumping unit always runs oil is that the packing gland or top wire is loose, resulting in the wellhead running oil, the process is wrong or the outlet valve is not opened, and the wellhead is under pressure, causing the wellhead to run oil slowly, the oil temperature section is too low early or the outlet pipeline is not smooth, and the oil well back pressure is high, resulting in the wellhead running oil.

Suggestion: Dear [Xian Hall File Flower] Now that the epidemic is repeated, you must pay attention to the <> of the slag when you go out and pretend to be chaotic

Wear a mask when you go out, wash your hands frequently! Have a great day, <>

The above is the full reply of the teacher2Have more questions? The teacher can continue to answer your <>

Looking forward to serving you again <>

I wish you a happy life in the wild hall and all the best! 4.If you are satisfied with my service, please give a thumbs up and wish you all the best again! Peace and spine with joy <>

1.Improper installation causes: when the range hood is installed, if the elevation angle is insufficient, the oil pollution will not be able to enter the oil tank or oil tank smoothly, and even reverse flow, which will naturally lead to oil dripping or oil leakage.

This kind of oil leakage problem will occur in the early stage of use, we can remove the range hood and reinstall it to ensure that the elevation angle is high in the front and low in the back. 2.Clogged oil groove results in:

The oil groove in the range hood is used to concentrate the oil smoke, if it is not cleaned for a long time, it will be blocked, or full of oil, and it will leak out if you continue to use it. This situation will generally appear after a period of use, and it is necessary to thoroughly clean the oil tank, which can be solved, and the oil tank needs to be cleaned regularly in subsequent use.

1. When the pumping unit is up: the pumping unit pulls the sucker rod to work upward, and the motor runs under heavy load, and the current is the largest.

2. When the pumping unit goes down: the pumping unit puts down the sucker rod, the motor runs without load, and the current is minimized.

3. In order to adjust the current gap between the upper and lower pumping unit, a counterweight steel plate is installed on the pumping unit, and when the pumping rod goes down, the counterweight steel plate is raised to the highest place to generate gravitational potential energy; When the sucker rod is going up, the counterweight steel plate converts the gravitational potential energy into kinetic energy to assist in lifting the sucker rod. In this way, the current at the time of pumping is reduced, the current at no-load is increased, and the position of the counterweight steel plate is adjusted, so that the difference between the peak current of the two can be minimized.

Generally, it may be that the oil smoke enters the touch switch system and causes poor contact and makes the touch switch not very sensitive, so you can only change a touch switch. It is recommended that you ask a professional maintenance person to inspect and repair it for you.

Abstract: In the collection of oil, we will see a machine that has been "kowtowing" on the ground, which is the pumping unit, which is a kind of machinery and equipment for oil extraction. So what is the role of the pumping unit?

Isn't it interesting that the pumping unit is like a bucket in a well, and its function is to salvage the oil from under the ground and collect the oil? Next, this article will briefly introduce what Xiangla shouts is a pumping unit and what is the role of the pumping unit, let's take a look at it in the article! 1. What is a pumping unit.

The pumping unit is a kind of machinery and equipment for mining Shijinye oil, commonly known as "kowtow machine". The pumping unit is the most important lifting equipment in the rod pumping system. According to whether there is a beam or not, it can be divided into beam pumping unit and beam non-beam pumping unit.

1. The basic characteristics of the beam pumping unit are simple structure, easy to manufacture and easy to use, especially it can operate in the oilfield for a long time and is reliable. Therefore, it is still the most widely used pumping unit, although it has the disadvantages of greater acceleration, poor balancing effect, lower efficiency, large volume and bulkiness at long strokes.

2. In order to improve the motion performance of the pumping unit, improve the energy-saving effect, and reduce the weight and floor area of the whole machine, the beamless pumping units used in the oilfield field in recent years mainly include chain pumping units and steel rope pumping units.

1) Chain pumping unit.

In terms of structural principle, it is different from the beam pumping unit in that it uses a crank slider mechanism. The working principle is to be powered by the power machine, and the high-speed rotation of the power machine is changed to the low-speed rotation of the chain through the reducer, and the rotary motion is changed to the upward and lower reciprocating motion of the pumping unit shuttle by the special chain link and the spindle pin-slider mechanism, and the deep well pump is driven to work by the suspension assembly that bypasses the day wheel.

2) Steel rope pumping unit.

The appearance is similar to the chain pumping unit, and its principle and structure are different in that it directly controls the motor through the control system to drive the drum to rotate forward and backward, and drives the deep well pump to work through the suspension assembly that bypasses the drum. It has also not been widely used due to long-term reliability problems of electrical systems. Other beamless pumping units, such as hydraulic pumping units and crank connecting rod pumping units, have also been tried.

Second, what is the role of the oil ballast machine?

In fact, the pumping unit has the same function as the bucket that we usually dig at home, pumping oil up through the pumping effect of a piston rod (sucker rod), and then sending it away through a buried pipeline. The only difference is that the action of this lever is driven by a motor.

Therefore, the main role of the pumping unit in oil exploitation is to lift the bottom of the well to the surface through the pumping rod and pumping pump.