I ve been wearing film on my car for two days, and it s raining today, can I drive?

The film should not only choose regular products, but also pay attention to the construction process of the car film. Because the effect of the film depends largely on the application process.

1. In order to avoid dust and impurities affecting the effect of the film, the body glass should be cleaned first before the car film.

2. The parts that may be damaged during the car film should be covered in advance to prevent scratching the car paint, interior and other parts; Accessories that may affect construction also need to be disassembled in advance.

3. After the overall treatment of the car body, it is necessary to start cutting the car film, and the car film should be preliminarily cut according to the size of the glass.

4. Paste the roughly cut car film on the car glass, and then the front and rear gears need to bake the film according to the amplitude of the car glass, and the effect is to make the amplitude of the car film close to the glass, so that the car film will be flat and free of water marks.

5. After baking, the film will be very obediently attached to the glass, and then it is necessary to make further corrections, that is, according to the shape of the glass, the corresponding shape will be finely cut.

6. The glass film is pasted inside, so the key step is to put on the film, and the requirement of the upper mold is to clean the inside of the glass, which is fast and accurate, and pushes out the moisture as soon as possible.

7. After all the work is done, the last need to do an inspection work, after the whole vehicle is pasted, the situation of each window should be checked, especially the corners, and the blistering phenomenon should be dealt with immediately.

Reminder: After the film, it is required that the window cannot be opened for 2-5 days, the rear gear cannot use the defogging function, and the front windshield cannot use the air conditioner to blow the air; Do not use toothed objects to scratch the glass; After the construction is completed, the warranty application form must be filled in, so that the after-sales service in the future can be guaranteed; After 3 days of car film, it is best to go back to the store for a re-inspection, and if there is any quality problem, it should be repaired in time.

Yes. The membrane is attached to the inside. Just can't drop the window.

Yes, it can be opened.

If you try to avoid washing the car and getting wet in the rain within three days after the film is applied, so as not to cause the car film to fall off due to the moisture not drying.

After attaching, you can wipe the film surface with a damp towel, sponge or soft cloth. In addition, some time after applying the film, you will notice that there is a foggy water vapor inside. This is a normal phenomenon in the process of drying the solar film, and it will slowly disappear after a while.

If the film is accidentally loosened under the influence of water, it is necessary to return to a professional film shop and have it re-fixed by a professional to ensure the effect and durability. If there is a stain on the surface of the film, never wipe it with a chemical solvent, you can use a rubber wiper to clean it.

Precautions: 1. The site with solar film must keep the environment clean, try not to use electric fans, and do not construct on the roadside.

2. The window glass must be absolutely clean, and it must be cleaned repeatedly, if there are dust particles remaining on the glass, it will seriously affect the adhesion and clarity of the solar film.

3. The solar film is only attached to the inside of the glass.

4. Predetermined type of surface.

It is not difficult to attach the solar film to the flat side window glass, but it is technically demanding to attach it to the curved front and rear windshields, and it is generally necessary to use the outer side of the front and rear windshields as a model to heat the solar film.

The predetermined method is to spread the protective film of the solar film outwards on the outside of the curved glass, sprinkle water between the solar film and the glass, use a temperature-adjustable hair dryer to heat the solar film, and squeeze the bubbles and water on the glass with a plastic scraper while heating, so that the solar film is deformed until it is completely consistent with the curved surface of the glass. Special attention should be paid to the fact that the heating should be uniform and not too concentrated, otherwise the temperature is too high and may cause the glass to crack.

5. Film process.

Spray water on the inside of the clean glass, then peel off the protective film of the solar film, and spray water on the glued surface, then the sun film can be attached to the glass, and then squeezed with a plastic scraper to remove air bubbles and excess water in the solar film. For curved glass, if the individual parts do not match, it can also be heated with a hair dryer to deform it and achieve a complete fit. When the film dries, it adheres firmly to the glass.

It is possible to photograph a new car on a rainy day. Since there is less dust in the gas on rainy days, the impact of dust during the film application process can be greatly reduced. The laminating workshop is generally closed, and no one else is allowed to enter during construction.

More sophisticated dealers are also equipped with watering equipment, that is, installing a watering system at the door of the workshop to prevent dust from flying in outside the door and provide a better working environment for car film.

Before pasting, the store will clean the glass of your car, which is the basis for the quality of the paste. There are generally three steps in cleaning glass: glass flaw detection, removal of colloidal particles, and cleaning of glass dust.

When cleaning, take care to prevent water from entering the car audio or electronic control system. When cleaning the windshield before applying the film, be sure to be careful with the protection of the heating wire. Finally, you can ask the store to hang the front and rear windshields without operation, otherwise it will lose its explosion-proof performance and affect the aesthetics.

When sticking the film, spray water on the inside of the clean glass first, then tear off the protective film of the car film, spray water on the surface of the coating film, so that the car film can be attached to the glass, and then extrude it with a plastic scraper to remove the bubbles and excess water in the car film. For curved glass, if some parts do not match, it can also be heated with a hair dryer to deform it and achieve a perfect match. After the solar film dries, it can be firmly attached to the glass.

It is also possible to apply a film to a new car on rainy days. Because there is relatively little dust in the air on rainy days, it can greatly reduce the harm of wind and sand in the whole process of filming. The film workshop is generally fully enclosed, and in the case of engineering construction, it politely refuses to enter the miscellaneous personnel.

The first business to pay attention to a little bit also has a shower machine and equipment, that is, to install a sprinkler system software at the door of the workshop to prevent the dust at the door from flying in, and to give a faster office environment for the vehicle film.

Before the film, the merchant will carry out the cleaning work of your vehicle glass, and the cleaning of the glass is the premise of the quality of the installation. Generally, there are three processes for cleaning glass: glass flaw detection, removal of sealing glue and glass ash removal and cleaning.

Be careful not to add water to the vehicle's loudspeakers or electronic control system during cleaning. When cleaning the windshield before the film, try to be careful about the maintenance of the ECG heating pipe. In the end, you can stipulate that when the merchant pastes the front and rear windshields, they do not need to use the knife, but must paste the whole thing, otherwise they will lose their explosion-proof type and affect the aesthetics.

When sticking the film, it is necessary to spray water on the inside of the clean glass, then tear off the protective film of the car film, and spray clean water on the surface of the dispensing, so that the car film can be pasted on the glass, and then use a plastic scraper to carry out squeezing to remove the small bubbles and excessive water in the car film. For inclined glass, if some positions do not match, it can also be heated with a hair dryer to deform it and fully match. After the automotive solar film dries, it can adhere firmly to the glass.